Parts for Thermador MCM255: 04 - Oven Body Parts

This bolt is a direct replacement fastening screw used to secure components and panels in compatible Bosch appliances. It restores secure mounting and reduces movement that can cause noise or part misalignment. What it does:

• Secures panels, brackets, or components to the appliance frame
• Prevents rattling and vibration from loose fittings
• Restores correct alignment of attached parts
• Maintains safe, secure connections during normal appliance operation

• One replacement bolt

• Disconnect power and water (if applicable) before servicing
• Use the correct driver or wrench to avoid stripping the head
• Tighten until snug—do not overtighten to prevent thread or part damage

This mounting bracket secures a dishwasher component to the cabinet or chassis, restoring proper panel alignment and reducing movement. It's a simple replacement for a bent, broken, or missing bracket to improve fit and quiet operation. What it does:

• Provides a secure mounting point for door/panel or internal components
• Keeps panels and trim aligned to prevent gaps and rubbing
• Reduces rattling or movement caused by a loose or damaged bracket
• Restores stable attachment after impact or corrosion-related failure

• Disconnect power and turn off the water supply before starting work
• Basic hand tools (screwdriver, nut driver) are typically required
• Support the panel or component while removing and installing the bracket to prevent dropping
• If fasteners are corroded or damaged, replace them with like-for-like hardware

This part has been discontinued by the manufacturer and is no longer available.

This part is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This Bake Element is an OEM part for Bosch Ovens. It's responsible for providing heat in the oven cavity for baking and cooking purposes. With prolonged use, the bake element can wear out or malfunction.

Frequent use at high temperatures can cause the bake element to deteriorate over time. Physical damage or overheating may also contribute to its failure.

Symptoms of a Bad Bake Element:

• Uneven cooking or baking
• Inconsistent oven temperatures
• Oven takes longer to preheat

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This latch assembly secures the dishwasher door during operation so the cycle can start and run safely. It replaces a worn or broken door latch to restore proper door closure and reliable cycle starts. What it does

• Secures the door closed so electronic controls detect a closed door and the wash cycle can begin.
• Prevents the door from popping open during a cycle, reducing leaks and interruptions.
• Commonly used when the door won't latch, the appliance won't start, or the door latch feels loose or broken.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Access may require removing the inner door panel and exterior trim; keep fasteners organized.
• Inspect door strike and surrounding trim for damage; replace any broken parts to ensure proper fit.
• After install, test door closure and run a short cycle to confirm proper operation and no leaks.

This wire oven rack slides into the oven's side supports to hold cookware at the correct height. Replace a bent, rusted, or missing rack to restore safe, level support and smooth sliding for baking, roasting, and broiling. What it does:

• Provides a stable, level surface for pans and dishes on the oven's side rails
• Lets you position food at multiple heights for proper cooking and airflow
• Slides in and out for easy loading and unloading when properly seated
• Common replacement reasons: bent/warped wires, flaking finish or rust, rough sliding, or poor fit

• 1 oven rack

• Allow the oven to cool completely; wear gloves to avoid sharp edges
• Pull the old rack straight out; clear debris from the side rails
• Align the new rack with the side supports and slide it in; ensure stops face the back if present
• Ensure the rack is evenly seated on both rails before placing cookware

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This door switch detects when the door is fully closed and latched. Replacing a worn or stuck switch restores safe, consistent start/stop behavior and ensures the unit only runs with the door securely shut. What it does:

• Senses door position and signals the control to enable/disable operation
• Prevents the appliance from running with the door open
• Resolves issues such as: won't start despite power, stops when the door is jostled, "close door" message, or needing to press on the door to run
• Helps restore reliable cycle start and proper safety interlock function

• 1 door switch

• Disconnect power at the breaker before servicing
• Access the switch behind the door panel or latch area; note wire locations or take a photo
• Move wire connectors to the new switch one at a time; ensure terminals are fully seated
• Reassemble and test door closure and operation before returning to service

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This is a replacement mounting screw used to secure components and panels in compatible Bosch appliances. It provides a simple way to restore proper fit and prevent loose parts or rattling. What it does:

• Fastens panels, brackets, or small components to appliance frames
• Restores secure mounting when original screw is missing or damaged
• Helps stop vibration-related noise from loose parts
• Matches OEM fit and thread for reliable fastening when the correct screw is specified

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage or cracking nearby plastic
• Turn off and unplug the appliance or disconnect power before accessing internal components