Parts for Maytag MLG19PNDWW: 10 - Cabinet-Rear (Washer) Parts

Color: White This part has been discontinued and is no longer available.

Specs: 10 - 16 x .375

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

Screw: 8-16 x 3/8 inch.

Specs: 10 - 16 x .375

This drain hose carries used water away from your appliance during the drain cycle. Replacing a worn or damaged hose helps stop leaks and restores proper draining performance.

• Routes wastewater from the appliance's drain system to the household drain
• Replaces hoses that are cracked, brittle, clogged, or kinked and leaking
• Can help when cycles end with standing water or slow/failed draining
• Helps reduce odors and backflow when installed and routed correctly

• Disconnect power and water supply; allow the appliance to cool before servicing
• Move the unit for access; keep towels or a pan handy to catch residual water
• Transfer and tighten existing clamps/fittings to the new hose; route without kinks and secure per your model's instructions
• Run a short test cycle and check all connections for leaks

Screw: 8-16 x 3/8 inch.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

This small strainer sits inside the washer's water inlet valve and screens out sand, rust, and sediment from the supply lines. Replacing a clogged or missing screen restores normal fill flow and helps protect the valve.

• Filters debris from incoming hot and cold water before it reaches the valve and tub
• Helps maintain consistent water flow during the fill cycle
• A clogged or damaged screen can cause slow fill, very long fill times, or no fill
• Common causes for replacement include mineral buildup or rust/sediment from supply lines

• Unplug the washer and turn off both water supplies
• Place a towel or shallow pan, relieve hose pressure, and disconnect the fill hoses from the inlet valve
• Carefully pull out the old screen (needle-nose pliers work well); press the new screen fully and evenly into the valve port
• Reconnect hoses, restore water and power, and check for leaks
• Tip: Many washers have separate hot and cold inlets—inspect both screens and replace as needed

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

Specs: 10 - 16 x .375

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.