Parts for Briggs & Stratton 126T02-0133-E2: Air Cleaner, Exhaust System Parts

The breather tube is responsible for filtering out exhaust gases from the crankcase. It has special fibers in the tube to remove contaminants as it moves the exhaust gases through the ventilation valve and out into the air. The tube also helps ensure that the engine air stays cool for optimal performance. This rubber tube can become dry and cracked over time, or it could be damaged due to an incident or impact. In any case, the tube should be fully replaced when it is not functional to ensure optimal performance at all times. This genuine OEM breather tube is manufactured to exact standards and made by Briggs and Stratton. It is compatible with select engines on more than 150 lawn mowers and generators from Toro, Briggs & Stratton, and Lawn Boy. This replacement tube is made of high-quality materials and sold as an individual part. No hardware or other parts are included with the purchase. This part should only be replaced once the engine is cool and all work should be done in a well-ventilated area. A screwdriver and socket set will be required to replace this part.

This air cleaner gasket keeps air from leaking out. It seals the carburetor's top and air cleaner base together, preventing debris that may enter underneath the cleaner and completely bypass the filter. The carburetor needs clean air to make the combustible mixture for the engine. When tiny particles enter, carburetor and engine performance issues arise like rough starting and flooding. An air cleaner gasket replacement is easy. Disconnect the spark plug wire first. Then, remove the air cleaner door and remove the carburetor cover using a nut driver or a screwdriver. Unscrew the fasteners holding the air cleaner housing and then pull the housing towards you. Use a flat screwdriver to dislodge the gasket at the back. Align the new replacement into the housing and reassemble the components. This air cleaner is a genuine component of Midwest Engine. This brand-new OEM air cleaner will work with lawnmowers, engines, pressure washers, wood chippers, and generators made by Toro, Lawn-Boy, Craftsman, Simplicity, and Briggs & Stratton. This part is sold individually. Bolts and screws for the air cleaner housing are sold separately.

This replacement thermostat is made from metal and composite components. The thermostat is responsible for reading the temperature of the engine and regulates the opening and closing of the choke. The thermostat could wear out and no longer work properly. This would require a replacement to ensure that the choke is properly managed, so the engine runs correctly and receives cooling when needed. If the thermostat is not working properly, the engine could run too hot and overheat. This is a genuine OEM replacement part that is sold individually. The thermostat can be used on several different makes and models of Lawn Mower and wood chipper. It can also be used on other types of small engines. The replacement thermostat is compatible with models from Briggs & Stratton, Toro, Cub Cadet, Lawn-Boy, and Simplicity. Buyers will always want to ensure they are buying the correct thermostat for their make and model.

This screw is designed to be used on all sorts of lawn and garden equipment. The metal screw is durable and attaches to the muff guard bracket to keep it in place and stable while the equipment is being used. This screw can become damaged through overuse or wear and tear. It can also break or become stripped, which will require it to be replaced.Visually inspecting the area with the muff guard bracket is connected to the rest of the equipment will give information about whether the screw is broken or damaged. The screws can also be cleaned to be more visible so small problems are easier to pick up on. Sometimes the screws can become loose, which is another situation where a replacement is needed. Simply use a screwdriver to take out the old screw and replace it with a new one.This screw is a genuine OEM replacement part that is directly sourced from the manufacturer. It comes as an individual part. The screw can be used on snowblowers, lawnmowers, lawn tractors, tillers, pressure washers, leaf blowers, edgers, generators, wood chippers, and log splitters made by MasterCut, Simplicity, MTD, Snapper, Lawn-Boy, Wheel Horse, Cub Cadet, Toro, Craftsman, and Briggs & Stratton.

This standard engine screw is responsible for securing various components and has multiple applications or locations, depending on the type and model of the lawn and garden equipment. It needs to be in good condition to continue to work effectively. Over time, however, hardware can come loose, be lost, break, or be otherwise worn or damaged, which would require a replacement. This screw can provide a solution for a number of applications on various engines. This genuine OEM replacement screw is manufactured to exact standards by Briggs & Stratton. It is compatible with hundreds of engines in lawn mowers and generators. Check the owner's manual for part location, as well as appropriate replacement procedure. This screw is made from durable metal and sold as an individual unit. Those who need more than one screw will have to order multiple quantities. This hardware should always be installed properly according to the manufacturer's recommendations and is a specialty screw that has specific uses. Not using the OEM screw replacement could cause operational issues or void any warranties that are in place.

This is replacement air cleaner screw is compatible with a range of different types of lawn and garden equipment that have air cleaners. The screw is used to ensure the air cleaner is properly fastened to the machine. Without the screw, the air cleaner would not stay in place. The air cleaner screw could suffer damage in a range of ways. It might simply be from wear and tear or corrosion from the elements. In addition, it could have been damaged or the threads could have become stripped. If the threads are damaged, it will not hold properly. The air cleaner screw could have been lost, as well. In any of these instances, the owner will want to replace the screw. This is a genuine OEM replacement air cleaner screw that is sold individually. The screw can be used with pressure washers, wood chippers, chainsaws, leaf blowers, lawn mowers, and other small engines with an air cleaner. Compatible brands include Craftsman, Briggs & Stratton, Toro, Cub Cadet, Homelite, Murray, Simplicity, Lawn-Boy, and MTD.

This filter is used for lawn and garden equipment. A dirty or clogged filter could cause the engine to run poorly.

This genuine Midwest Engine air filter cleaner can be used as a replacement part for the small engine of power washers. The purpose of an air filter cleaner for a power washer is to prevent the accumulation of debris, dirt, pebbles, and other such external materials that could be sucked into the engine through the air filter and cause damage to the internal components of the appliance.Air filter cleaners might have to be replaced several times within the regular lifespan of a power washer as a part of routine maintenance. If the air filter cleaner is damaged by the intake of dirt and debris or is otherwise punctured, pierced, ripped, torn, or eroded over time, the air filter cleaner should be removed immediately and replaced with this genuine OEM replacement part before using the small engine appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This air filter cleaner is compatible with the following brands: Midwest Engine, Briggs & Stratton, and Troy-Bilt.

This is a foam pre-filter that is used to help prevent dust, pollen, and other debris from clogging the air filters of small engines. One of the most common problems faced by small engines is an inadequate air supply caused by air filters that have become mired with airborne debris. Cleaning or replacing filters can become a tiresome and expensive proposition. If filters are not adequately cared for, they perform poorly, waste gasoline, pollute the air, and cause internal engine damage. A good way to help an air filter do its job is by adding a foam pre-filter in the air filter compartment. Pre-filters are exposed to all the things that clog air intakes, so periodically, they also must be replaced. Foam pre-filters are designed to fit snugly inside the housing of the air filter of virtually all small engine housings. To install a pre-filter, remove the air filter housing by taking off the one screw holding it in place. Remove the air filter from the housing and place the pre-filter inside against the exterior wall of the housing with the arrows pointing up. Reinstall the air filter. The paper of the filter should fit perfectly against the labeled side of the pre-filter. Now simply reattach the air filter housing. Genuine Midwest Engine makes this OEM replacement part, and it is sold separately.

This screw is designed to be used on all sorts of lawn and garden equipment. The metal screw is durable and attaches to the muff guard bracket to keep it in place and stable while the equipment is being used. This screw can become damaged through overuse or wear and tear. It can also break or become stripped, which will require it to be replaced.Visually inspecting the area with the muff guard bracket is connected to the rest of the equipment will give information about whether the screw is broken or damaged. The screws can also be cleaned to be more visible so small problems are easier to pick up on. Sometimes the screws can become loose, which is another situation where a replacement is needed. Simply use a screwdriver to take out the old screw and replace it with a new one.This screw is a genuine OEM replacement part that is directly sourced from the manufacturer. It comes as an individual part. The screw can be used on snowblowers, lawnmowers, lawn tractors, tillers, pressure washers, leaf blowers, edgers, generators, wood chippers, and log splitters made by MasterCut, Simplicity, MTD, Snapper, Lawn-Boy, Wheel Horse, Cub Cadet, Toro, Craftsman, and Briggs & Stratton.

This exhaust gasket is a genuine Midwest Engine replacement part for appliances operated by small engines, such as chipper shredders, snowblowers, leaf blowers, and lawn mowers. An exhaust gasket's purpose in the engine is to create a sealed layer between the carburetor and the exhaust tube to keep dirt and debris out of the infrastructure of the engine. A malfunctioning or broken exhaust gasket could compromise the seal between the carburetor and the exhaust tube, meaning that dirt and debris could get into the engine and cause damage. An exhaust gasket could be subject to damage from overuse and is generally known to require replacement over time from general wear and tear. If the exhaust gasket seal is compromised, it should be replaced immediately. Evidence of dirt and debris compromising an engine could take the form of oil leaking from the carburetor, black smoke pluming from the exhaust tube, and lower engine pressure than usual. This exhaust gasket is compatible with the following brands: Briggs and Stratton, Cub Cadet, and Toro. This part sold individually.

This is a genuine OEM replacement air cleaner primer base for select Briggs & Stratton engines. The air cleaner base is installed on the engine to secure the air filter, which cleans debris from the air as it goes into the engine. Along with the cover, the air cleaner base provides a secure location and protection from the elements. Over time or during the course of other repairs, the base may become cracked or damaged, which could affect the operation of the air filter and the engine performance overall. This needs replaced as soon as possible to prevent further damage. This OEM air cleaner base is compatible with select engines manufactured by Briggs & Stratton, including those found on generators and lawn mowers. There are more than 150 machines that use this part from Toro, Simplicity, and Briggs & Stratton. This air cleaner primer base assembly includes the primer bulb and is sold as an individual unit. Allow the engine to cool completely and wear gloves when doing engine repairs.

This OEM air cleaner cover from Briggs & Stratton fits over the air cleaner and filter system, protecting the filters from excess dirt, debris, and other potential damage. This cover is also designed to help hold the air filter in place. The plastic housing is durable, but it can be subject to damage over time. This replacement is a snap-on cover, so no tools are required. Be sure to wear gloves when performing any kind of work on lawn and garden equipment. This air cleaner cover is designed to work with multiple types of lawn and garden equipment from Briggs & Stratton, Lawn-Boy, and Toro. It works with various engines on generators and lawnmowers, including hundreds of different specific models. It is sold individually and does not include the actual air filter or the bottom part of the housing.

The primer is used to help circulate fuel to the carburetor, which ensures that the engine starts quickly. Primers can start to wear out over time, which can cause the engine to leak gas or the engine not to start at all. In those cases, it is time to look at the carburetor primer to see if it is properly in place and that it is still in good shape. If there is an issue, it is time to replace it. This genuine OEM replacement carburetor primer part is high-quality and is made to work with lawn mowers and small engines from a range of different brands. These brands include the likes of Craftsman, Briggs & Stratton, Toro, Cub Cadet, Lawn-Boy, and Simplicity.