Parts for Lg LW8016ER/00: Air Conditioner Parts

This clamp secures a line or connection inside your appliance, maintaining a tight fit under vibration. Replacing a fatigued clamp helps prevent leaks or disconnections and keeps components anchored so the system operates reliably.

• Holds a line/fitting firmly to keep the joint sealed and secure
• Helps prevent leaks or disconnections at hose/tube connections
• Resists vibration that can loosen fittings during operation
• Replace if bent, weakened, or corroded, or if the connection repeatedly loosens

• Disconnect power and, if applicable, shut off water supply before service
• Note clamp orientation and routing; seat the clamp just behind the fitting bead/stop
• Use the correct tool for your clamp style to compress or tighten evenly
• After reassembly, restore utilities and test for leaks or movement

A replacement frame assembly that restores the appliance's front trim and helps keep the control area and door edges protected and aligned. Use this genuine-style part to replace cracked, bent, or cosmetically damaged front trim. What it does:

• Replaces the visible front trim or bezel that surrounds the control/door area
• Restores a flush, finished appearance and helps prevent debris from entering internal components
• Helps ensure proper alignment of the door/control opening when the existing frame is warped or damaged
• Commonly used when the trim is cracked, dented, loose, or shows cosmetic damage

• Always disconnect power before starting any repair to avoid shock or injury
• Remove any trim screws or clips holding the existing frame; retain fasteners unless a replacement set is specified
• Handle the replacement carefully to avoid scratching the finish; align tabs/clips before securing

This replacement power cord assembly restores the appliance's main electrical connection so it can safely receive power and operate. Use it to replace a frayed, damaged, or non-working line cord and regain reliable power delivery. What it does:

• Provides the main electrical connection between the appliance and your home power outlet
• Replaces damaged or worn cords that can cause intermittent power or prevent the unit from turning on
• Helps eliminate issues caused by frayed wiring, exposed conductors, or a loose inlet connection
• Supports safe operation when installed with proper grounding and strain relief

• Always disconnect power at the breaker or unplug the appliance before starting any work
• Verify the cord matches the appliance inlet and routing; secure strain relief and clamps per service instructions
• Tighten all terminal connections and inspect for proper grounding before restoring power

Restore full remote control function with this replacement remote controller assembly. Replaces a damaged or unresponsive remote PCB and button cluster so the unit responds reliably to power, volume, input and menu commands. What it does:

• Replaces the internal circuit board and button interface that transmit IR/remote signals.
• Fixes symptoms like unresponsive or intermittent buttons, no power or no signal from the remote.
• Restores control of common functions such as power, volume, input selection and menu navigation.
• Useful when buttons are stuck, the remote was dropped, or the internal electronics are damaged.

• Remove batteries and disconnect power from the appliance before replacing the assembly.
• Handle the PCB by its edges to avoid damage from static or oils; keep small screws and clips organized.
• Reassemble the remote housing carefully to avoid pinching ribbons or misaligning buttons.

The Display PCB Assembly is an OEM part for LG microwaves. Located behind the control panel, it houses the critical electronic components that power the display screen and control functions. The PCB assembly is designed to interface the control inputs and outputs with the microwave's operational systems.   

Causes of a failing PCB can include moisture damage, component failure due to power surges, or cracks/breaks from accidental impact over time.

Symptoms of a bad Display PCB Assembly include:

• Black or non-responsive touchscreen  
• Inability to power on or select cooking presets
• Erratic control behaviors such as random button presses
• Recurring electronic or operational error codes

This OEM LG replacement part is also compatible with Sears/Kenmore microwave models. 

This is the main electronic control board for the appliance. It manages and coordinates power to key components, helping the unit run correctly and respond to user settings.

• Regulates and distributes power to compressors, fans, valves, and other loads
• Interprets sensor and user input to control cooling and defrost cycles
• A failed board can cause no power, no cooling, unresponsive controls, or intermittent operation
• Resolve issues like lights/fans not running or error codes related to control faults

• Disconnect power before servicing; capacitor discharge may be required
• Handle the board by edges and avoid touching components to prevent ESD damage
• Photograph/wire-note all connections before removal; move connectors over one by one
• Mount securely and verify all harnesses are fully seated before restoring power

This vent damper assembly keeps outside air and pests from entering the appliance while allowing exhaust to exit freely. It restores proper airflow and helps prevent cold drafts or backflow when the appliance is off. What it does

• Serves as the one-way flap for the external vent, opening during exhaust and closing afterward.
• Stops outside air and pests from entering the ducting when the appliance is idle.
• Helps reduce backdrafts that can affect drying or venting performance.
• Can reduce stray airflow and cold drafts into the laundry area.

• One vent damper assembly.

• Always disconnect power (and gas supply for gas appliances) before servicing.
• Access typically from the rear vent outlet or through the exterior vent hood; basic hand tools required.
• Ensure correct orientation so the flap opens outward with exhaust airflow.
• Inspect surrounding seal and ductwork; replace any damaged screws or gaskets during reassembly.

The Axial Fan is an OEM part for LG air conditioners. It is designed to circulate air across the evaporator and condenser coils, ensuring efficient heat exchange and cooling performance. This fan is crucial for maintaining the airflow needed to keep your air conditioner functioning optimally.

Causes of a bad axial fan can include wear and tear over time, debris buildup on the fan blades, or motor failure. Such issues can impede the fan's ability to rotate properly, reducing the efficiency of your air conditioning unit.

Symptoms of a bad axial fan include:

• Reduced cooling performance
• Unusual noises during operation
• The air conditioner cycling on and off frequently
• Increased energy consumption due to inefficient cooling

This OEM LG part is also compatible with Sears/Kenmore.

This multi harness is a factory-style wiring harness that connects multiple electrical components to deliver power and control signals, restoring reliable electrical communication for the appliance. What it does:

• Routes power and signal connections between control boards, sensors, switches and motors
• Replaces damaged or broken wiring that can cause intermittent or no power to components
• Common symptoms: appliance won't start, controls unresponsive, intermittent operation, or error codes related to communication
• Restores proper electrical connections when original harness shows wear, frayed wires, or connector damage

• Disconnect power to the appliance before starting any work
• Handle connectors gently; match connector shapes and colors for correct installation
• Route harness along original wire channels and secure with clips or ties—avoid sharp edges and heat sources

This multi-wire harness connects the control and several components inside your appliance, carrying power and signals through factory-molded connectors. Replace a damaged harness to restore reliable electrical connections and eliminate intermittent or dead component behavior. What it does:

• Distributes power and control signals between the appliance's control and multiple components via keyed connectors
• Restores secure connections when original wires or plugs are burned, loose, or damaged
• Maintains proper routing and strain relief to help prevent chafing, shorts, and intermittent faults
• Symptoms include intermittent operation, a component not running, failure to start, error codes, or visible heat damage/burnt odor from the wiring

• 1 multi-wire harness assembly

• Disconnect power to the appliance before servicing; turn off water or gas if applicable
• Photograph routing and connector locations before removal; transfer any clips/ties/retainers from the old harness
• Seat connectors fully; do not pull on wires—work by the connector bodies and match keyed plugs carefully
• Route away from sharp edges, moving parts, and hot surfaces; secure with all original clips and tie-downs