Parts for Frigidaire FEF450WCDA: 03 - Body Parts

Screw that adjusts and secures the leveling leg to your range base or bracket. Replace if stripped, bent, or missing to restore stable footing and level your appliance.

Chrome oven rack measures approximately 23" wide by 15" deep. Replaces missing, worn, or damaged racks in your oven. Direct fit for multiple models.

Color: chrome. Measures about 10 inches wide by 17 inches deep.

Oven light not working or saw a flash near the bulb? This light socket houses the oven bulb and is a straightforward DIY fix in under 30 minutes.

Illuminates your oven interior so you can monitor cooking without opening the door. Replace when burned out or dimming. Verify fit with your model number.

Replace your oven's light lens cover if cracked, broken, or missing. Protects the bulb and restores interior visibility. Confirm fit with your model.

This lower oven heat shield is a factory-style replacement panel that protects internal components from direct bake-broil heat and helps direct oven airflow for consistent cooking. Restores heat protection and prevents heat-related damage to nearby parts. What it does:

• Shields wiring, insulation and under-oven components from direct heat and hot spots
• Helps control internal oven heat flow for more even cooking
• Reduces risk of scorched or warped parts caused by excessive localized heat
• Common symptom: visible heat damage, burnt insulation, or a missing/warped shield

• Disconnect power (and gas supply if applicable) and allow the oven to fully cool before beginning work
• Handle carefully; edges may be sharp—wear gloves and eye protection
• Basic hand tools usually required; follow for exact fastener locations
• If corrosion or adjacent component damage is present, inspect and replace affected parts as needed

Nylon guide that supports the front of your range oven drawer as it slides in and out. Replace if cracked, broken, or worn causing drawer misalignment.

Insulates and cushions the oven cabinet interior. Replace if cracked, damaged, or missing to restore thermal separation and reduce condensation.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

Range won't power on or tripped breaker? Burnt or loose terminal block connections are often the cause. This kit restores safe power delivery. DIY-friendly.

Broiler not heating or turning red? This broil element restores high-heat broiling. DIY-friendly repair, typically takes 10-15 minutes with basic tools.

Oven won't heat or bakes unevenly? Replace the lower bake element to restore consistent heating. This DIY fix takes about 30 minutes with basic tools.

If your oven won't heat or bakes unevenly, the bake element may be burned out. This is a simple 5-10 minute repair—just two screws and wire connectors.

Adapter assembly for oven vent system. Installs in back wall to align vent components. Replace if cracked, broken, or missing to restore proper fit.

Rubber or plastic bushing that cushions and supports the oven door. Replace if cracked, worn, missing, or causing door misalignment or rattling.

Replace your oven's broken or missing rack spring. This small metal spring helps support and stabilize oven racks during sliding and positioning.

Rear wiring cover panel for your range. Shields electrical wiring connections at the back of the unit. Replace if cracked, broken, or missing.

This strike plate fits the door latch assembly to provide a secure contact point for the latch so the appliance door closes and stays latched. It restores proper door alignment and reliable closing action. What it does:

• Provides a durable contact surface for the door latch to engage
• Helps the door close fully and remain securely latched
• Reduces rattling or misalignment caused by a worn or damaged strike
• Can prevent door-open errors or improper sealing related to latch engagement

• Disconnect power to the appliance before starting any repair
• Remove the access panel or door trim to reach the strike; keep fasteners organized
• Align the strike plate with the latch before tightening screws to ensure smooth engagement

Fix a gas range with no ignition spark or clicking sounds. This transformer powers the ignition system. Common repair, typically takes 30-45 minutes.

This door retainer secures the door trim and inner door components to keep the appliance door aligned and stable. It restores proper door fit and prevents loose or rattling trim for safer, quieter operation. What it does

• Holds door trim/inner panel in place so the door closes and seals correctly
• Stops loose or vibrating trim that can cause noise or uneven gaps
• Helps maintain proper alignment to reduce strain on hinges and latches
• Common symptom: loose, misaligned, or rattling door trim

• One door retainer

• Disconnect power (or unplug) before starting any repair
• Remove door trim or inner panel per service instructions to access retainer
• Install the retainer in the same orientation; secure with the original fasteners