Parts for Frigidaire GCFG3060BDA: Body Parts

This mounting bracket secures internal components to the cabinet or chassis, restoring proper alignment and support in affected appliances. It's a direct-fit replacement designed to match the original part's shape and mounting points. What it does:

• Provides a stable mounting point to hold panels, rails, or assemblies in place
• Restores proper alignment to prevent rattling, sagging, or misaligned doors/panels
• Replaces worn, bent, or broken brackets that can compromise component support
• Compatible with the OEM mounting locations and fastener pattern for correct fit

• Remove power to the appliance before beginning any repair
• Use appropriate hand tools; avoid overtightening fasteners to prevent stripping
• Keep original fasteners and hardware; replace any damaged fasteners as needed

This replacement cover protects internal components and restores your appliance's finished appearance. It fits the factory location to keep parts shielded from debris and accidental contact. What it does

• Replaces a cracked, broken or missing cover to stop exposed components and reduce risk of damage
• Helps prevent debris and moisture from entering internal areas that can cause malfunctions
• Eliminates rattles or vibration caused by a loose or damaged housing piece
• Restores a clean, finished look to the appliance exterior

• Disconnect power to the appliance before starting any repair
• Basic hand tools such as a screwdriver may be required; keep fasteners from the original part for reuse if in good condition
• Handle part carefully to avoid scratching the finished surface during installation

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

This flat wire oven rack sits on the interior supports to hold cookware at the correct height. Replace a bent, rusted, or missing rack to restore a stable, level surface for safe, even baking and roasting.

• Provides a level platform for pans, bakeware, and dishes inside the oven cavity
• Enables accurate shelf positioning to follow recipe and cooking instructions
• Replace if the rack is warped, rusted, has broken welds, or no longer sits level
• Symptom clues: cookware wobbles, tips, or cannot be positioned properly on the supports

• Disconnect power and allow the appliance to cool completely before handling interior parts
• Wear gloves; wire ends and edges can be sharp
• Match the rack orientation to the support ledges and seat it fully on both sides
• Confirm the rack is level and securely seated before loading cookware

This replacement switch restores reliable control of a selected function by opening or closing an electrical circuit inside your appliance. When the original switch wears out, buttons may stop responding or features may not activate consistently.

• Opens/closes an electrical circuit when the button/actuator is engaged
• Routes power or sends a signal to the control or component
• Common symptoms: no response when pressed, intermittent operation, or function won't start
• May show signs of heat damage, loose terminals, or inconsistent "click" feel

• Disconnect power at the breaker before servicing
• Photograph or label wire positions to ensure correct transfer to the new switch
• Move wires one at a time; fully seat connectors on the correct terminals
• Reassemble, restore power, and test the function activated by the switch

This lamp assembly replaces a refrigerator interior light to restore safe, visible illumination for food storage areas. It provides a direct-fit housing and socket that mounts where the original interior lamp was installed. What it does:

• Houses and secures the refrigerator interior light so the compartment stays illuminated.
• Provides the electrical connection and socket for the interior lamp bulb.
• Common fix for lights that flicker, fail to turn on, or have a loose or damaged housing.
• Helps restore normal visibility for loading, unloading, and inspecting contents.

• Disconnect power to the appliance before starting any work to avoid shock.
• Handle the lens and bulb carefully to avoid breakage; replace the bulb if damaged.
• Use basic hand tools; avoid forcing fasteners—align tabs and clips to seat the assembly.

This shield is a small protective mounting plate that helps protect internal components from heat, debris and abrasion. It restores proper component clearance and prevents contact-related wear for safer, quieter operation. What it does:

• Covers and protects nearby components from heat and debris buildup
• Maintains correct spacing to prevent rubbing, chafing or noise
• Helps prevent damage that can lead to intermittent operation or visible wear
• Fits into the appliance's body where the original shield mounts

• One replacement shield

• Disconnect power before starting any repair to avoid shock or injury
• Remove the outer panel(s) as needed to access the mounting area; retain original fasteners
• Inspect adjacent parts for wear while installing the new shield

This oven temperature sensor probe monitors the interior temperature and sends readings to the range control for accurate cooking. Replacing a faulty sensor restores correct temperature regulation and more consistent bake/roast results. What it does:

• Senses oven cavity temperature and reports it to the control board
• Helps the oven reach and maintain set cooking temperatures
• Common symptom: oven not heating, running too hot or too cold, or uneven baking
• Works with the range/oven's electronic control to regulate heating cycles

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the oven back panel or interior access panel; handle panels and fasteners carefully
• Do not bend the sensor sharply or damage the probe tip or wiring
• Ensure the sensor connector is fully seated and secured before restoring power; verify operation with a test heat cycle

This power cord supplies electrical power to the appliance, restoring a safe, factory-style connection between the outlet and the unit. Use it to replace a damaged or worn lead to regain reliable power. What it does:

• Replaces a worn, frayed or damaged power lead to stop intermittent power or visible cord damage
• Restores a secure electrical connection when the original cord is cut, melted or has exposed wires
• Helps eliminate power-related failures caused by broken conductors or loose cord terminals
• Works as the external mains connection between the appliance and household power

• One power cord

• Always unplug the appliance or switch off house power at the breaker before replacing the cord
• Verify the cord's terminal type and wire count match your appliance before installation
• Tighten terminal connections to the manufacturer's specified torque and secure strain relief where provided

Note: ONE screw only, order as needed.

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

The Terminal Block Kit is an OEM replacement part for Frigidaire stoves. It includes all the necessary terminals needed to ensure connections are securely made in the stove's electrical system. As a distribution point, the terminal block facilitates connections between internal stove components and external power.  

Causes of a faulty terminal block can include worn terminals that no longer grip wires firmly, or compromised insulation that allows shorts over time. Without proper connections, stove functions may be disrupted.

Symptoms of a bad terminal block include:

• Intermittent or complete burner/oven failures  
• Buzzing or humming electrical noises
• Tripped circuit breakers or blown fuses
• Visible damage or corrosion on terminal connections

It is compatible with Electrolux, Gibson, Kelvinator, and Kenmore branded models as well.

This replacement evaporator fan blade helps circulate cold air inside the freezer or refrigerator compartment to maintain even temperatures and proper cooling performance. A direct-fit replacement when the existing blade is cracked, warped, or missing. What it does:

• Moves air across the evaporator to promote even cooling and frost prevention
• Restores proper airflow when a damaged blade causes noise or reduced cooling
• Helps reduce hot or warm spots inside the compartment
• Quiet, balanced operation when installed correctly

• One replacement evaporator fan blade

• Disconnect power to the appliance before starting any repair
• Typically accessed by removing interior panels in the freezer/refrigerator compartment
• Inspect the fan motor shaft and mounting for damage before installing the new blade

This is a replacement mounting nut used to secure components on compatible Frigidaire appliances. It provides a simple, reliable fastener to replace a missing, damaged, or corroded nut and restore proper part retention. What it does

• Secures panels, brackets, or hardware so parts stay in position during use
• Replaces stripped, rusted, or missing nuts that cause rattling or loose components
• Helps restore proper alignment and safe operation of the affected assembly
• Small fastener used wherever the OEM diagram specifies part 561231207

• One mounting nut (part number 561231207)

• Disconnect power or unplug the appliance before starting any repair
• Use the correct-size wrench or socket to avoid rounding the nut
• Tighten snugly but do not overtighten to prevent thread damage
• If the original nut was corroded, inspect mating threads and replace the bolt/stud if needed

This anti-tip kit secures a freestanding range or slide-in oven to help prevent the appliance from tipping forward, improving safety during normal use. Installs at the appliance base to anchor the unit to the floor or wall. What it does:

• Anchors the range to the floor or wall to reduce the risk of tip-over when the oven door or storage drawer is opened.
• Stops the appliance from rocking or shifting during normal use or when heavy cookware is placed on the open door.
• Provides a simple mechanical safety anchor recommended after installation, floor changes, or appliance relocation.

• Anti-tip bracket and mounting hardware.

• Follow the OEM installation instructions exactly; mount to the floor or wall surface specified by the manufacturer.
• Use proper anchors for your floor or wall type (masonry anchors or wood screws as appropriate); if the provided fasteners are not suitable, obtain the correct anchors.
• Disconnect power and move the appliance per OEM guidance before attaching the bracket.

This hex flange nut secures components where a broader bearing surface is needed to resist loosening and distribute load. It fits 10-32 threaded studs and is used on fastened assemblies in appliances. What it does:

• Provides a secure threaded connection for 10-32 screws and studs
• Flange spreads clamping force to reduce panel or bracket damage
• Hex shape allows tightening with a wrench for a reliable hold
• Commonly replaces worn or missing nuts that cause loose panels or rattling

• One hex flange nut

• Use the correct 10-32 screw or stud and hand-start threads to avoid cross-threading
• Tighten with an appropriately sized wrench; do not overtighten to prevent thread or part damage
• Disconnect power and follow appliance safety instructions before servicing
• Replace only like-for-like; confirm size and thread match your application

This factory screw secures components in your appliance, restoring a tight, rattle-free fit. Replace missing or damaged hardware to keep panels, brackets, and trim properly fastened and aligned for safe, reliable operation.

• Secures panels, brackets, trim, or internal components to the chassis
• Replaces lost, rusty, stripped, or cross-threaded screws
• Helps eliminate looseness, gaps, and vibration/rattling
• Common signs: loose/misaligned panels or trim, rattling noises, missing or rounded screw heads

• Disconnect power (and shut off gas if applicable); allow the unit to cool completely
• Match to the original location and replace one at a time to maintain alignment
• Hand-start to prevent cross-threading; tighten snugly—do not overtighten
• Use light torque when threading into plastic or thin sheet metal