Parts for Hot Point RGB518PCD2CT: Body Parts

If your range igniter won't spark, this battery holder restores reliable power to the control board. Secures batteries with stable contacts. Easy DIY fix.

Replace your worn, bent, or warped oven rack. Provides a stable surface for baking sheets and pans inside your range oven. Fits standard ovens.

Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

Replaces cracked, rusted, or corroded oven bottom pan and heat deflector. Installs in the base of your range oven cavity. Simple 2-screw removal.

8-18 x 1/2 inch screw for gas range assembly. Replace when missing, stripped, or corroded during oven repairs or maintenance work.

Speed nut for electric and gas ranges. Secures panels and components inside your range. Replace if stripped, missing, or no longer holding parts firmly.

Secures the thermostat sensing bulb to the oven cavity wall for accurate temperature control. Replace if missing or damaged to prevent sagging bulb.

Safety bracket that anchors your range to the floor or wall, preventing tip-over. Replace if missing, damaged, or cracked to secure the appliance.

This is the right side hinge guard. For left side use WB34K4.

This is the left side hinge guard. For right side use WB34K3.

Right-side guide support secures sliding drawer or shelf rails on your range. Replace if cracked, broken, or worn to restore smooth tracking and alignment.

Replaces cracked or damaged lower oven floor panel. Restores heat protection and support for cookware. Needed when panel is warped, sagging, or broken.

This support base secures the oven cavity and provides a stable foundation for the lower oven assembly, helping keep internal components aligned and preventing shifts during use. It restores correct support and fit for safe operation. What it does:

• Holds and stabilizes the oven cavity and lower components to prevent sagging or misalignment
• Restores proper clearance and support for the oven floor and related parts
• Helps eliminate noises or movement caused by a loose or damaged support
• Supports safe, even operation by maintaining correct internal positioning

• One support base

• Designed to replace the factory support base;
• Basic hand tools typically required;
• Disconnect power and gas (if applicable) before performing service

This support base provides a stable mounting surface for the appliance's cooktop/range components, restoring proper alignment and reducing movement. It helps keep parts seated securely for safe, even operation. What it does:

• Provides structural support and stabilization for the cooktop/range assembly
• Keeps components aligned to prevent gaps, rubbing, or uneven surfaces
• Reduces rattling, vibration and movement during use
• Helps maintain proper clearance for adjacent components

• One support base

• Disconnect electrical power (and gas, if applicable) before starting work
• Follow OEM service manual for disassembly and reassembly steps
• Use proper tools and avoid over-tightening fasteners to prevent damage
• If the cooktop or appliance has glass components, handle with care and use protective gloves

Replacement leveling leg for ranges. Installs at base corners to stabilize and level your range on uneven floors. Needed when leg is broken or missing.

Replace your gas range's damaged or worn oven top panel. This structural cover installs over the oven cavity, restoring your range's appearance.

This right oven side panel is a direct-replacement interior panel that restores proper fit and protection inside the oven cavity. It helps maintain correct airflow and keeps internal components covered for safe, reliable use. What it does:

• Replaces a dented, warped or rusted right-side oven interior panel
• Protects internal wiring, sensors and insulation from heat and debris
• Helps maintain even cooking by preserving the oven cavity shape
• Improves appearance by covering damaged or discolored metal

• Disconnect power to the range before starting any repair.
• Basic hand tools typically required; removal of oven racks and inner panels may be needed.
• Handle edges carefully — metal parts can be sharp.

Metal angle support bracket that secures interior panels, shelves, or trim inside your range. Replace if cracked, bent, or missing to maintain proper alignment.

Cushions your range oven door perimeter to prevent metal contact and reduce heat loss. Replace when worn, compressed, or door closes harshly. Confirm fit.

Insulation wrap that installs around the oven cavity to reduce heat loss and dampen sound. Replace if worn, torn, compressed, or missing.

This rubber bumper cushions and protects appliance components from impact, vibration and rubbing, helping reduce noise and wear. It restores proper spacing where a worn or missing pad lets parts contact or vibrate. What it does:

• Acts as a soft stop to prevent panels, doors or components from striking each other
• Dampens vibration and reduces rattling or buzzing during operation
• Keeps moving parts aligned by maintaining proper clearance
• Helps prevent cosmetic damage from rubbing or repeated contact

• Locate the damaged or missing bumper and remove any debris before installing
• Press or seat the bumper into the mating hole or surface until fully engaged
• Use common hand tools if needed; avoid sharp tools that can tear the bumper
• Disconnect power or follow appliance-specific safety steps before working near electrical components

Oven door won't close properly or seal tight? This hinge receiver bracket anchors the door hinge arm to the frame, ensuring proper alignment and seal.

Mounting screw that secures the hinge assembly on electric and gas ranges. Replace this fastener if the original is stripped, missing, or damaged.