Bracket & Flange

The Microwave Lever is an OEM part for GE built-in and over-the-range microwaves. This metal lever links to the door handle and activates the door switch when the handle is pulled open.

Causes of a bad lever can include wear from daily use over many years. Repeated opening and closing of the microwave door puts stress on the lever and surrounding components. 

Symptoms of a bad lever include:

• Power not disabling when door opened  
• Loose or improper connection to door handle
• Door not shutting or latching completely
• Delayed microwave engagement or shut-off

This GE part is also compatible with Hotpoint, RCA, and select Kenmore models.

This latch hook secures the refrigerator/freezer door, helping keep it closed for proper cooling and efficient operation. Replace a worn or broken latch hook to restore a tight door seal and reliable door closure. What it does:

• Engages with the strike or catch to hold the door closed
• Prevents unintended door opening that can cause temperature loss
• Restores smooth latching action when the original hook is damaged or bent
• Simple mechanical part—no electronics or wiring

• One latch hook

• Disconnect power to the appliance before beginning any repair
• Remove the inner door panel or access trim as needed to reach the latch area
• Use appropriate screwdrivers; keep fasteners organized for reassembly
• Test the door closure after installation to ensure proper alignment and seal

Rod retainer clip secures a support rod or shaft to keep moving parts aligned and stable during operation. Replacing a worn or broken clip prevents rattling, binding, or components falling out and helps restore proper mechanical function. What it does:

• Holds a support rod or shaft in place to maintain alignment of moving components.
• Prevents rods from sliding out or shifting, which can cause rattling, binding, or misalignment.
• Replace if the clip is bent, cracked, corroded, or no longer grips the rod securely.
• Common symptom: loose or misaligned parts, unusual noises, or components that detach during use.

• Disconnect power (unplug or shut off breaker) before servicing the appliance.
• Access may require removing panels, covers, or nearby components—follow the OEM service manual.
• Remove the old clip and carefully press or snap the replacement into place; avoid over-bending the clip.

Replacement Stackit2 3.0 module (TAW) designed to restore the intended fit and function of the Stackit2 assembly in compatible appliances. Offers a like-for-like replacement to address wear, damage, or missing pieces. What it does

• Replaces a worn, cracked, or missing Stackit2 3.0 module to restore proper assembly fit.
• Helps eliminate rattling, misalignment, or instability caused by a damaged module.
• Restores the original mounting/stacking interface so the appliance components seat correctly.
• Useful when visual damage or loss is present at the Stackit2 connection point.

• One Stackit2 3.0 module (TAW) as pictured.

• Disconnect power to the appliance before attempting any repair.
• Inspect surrounding components for additional damage before installing the replacement.
• Install in the original orientation; secure any fasteners removed during disassembly.

This is a replacement left/right mounting bracket used to secure interior panels or trim and restore proper alignment and fit. It provides a simple fix for loose panels and misalignment without replacing larger assemblies. What it does:

• Secures an interior panel, trim piece, or rail to the appliance cabinet
• Restores proper alignment to reduce rubbing or binding of doors or panels
• Prevents rattling or movement caused by worn or broken brackets
• Helps maintain correct spacing for connected components

• Basic hand tools typically required; refer to your appliance's service manual for the exact procedure
• Disconnect power (and gas if applicable) before beginning any repair to avoid shock or injury
• Keep removed fasteners and parts organized for reassembly; replace any damaged screws

This freezer drawer bracket secures and supports the freezer drawer, keeping it aligned and stable for smooth operation. It replaces a worn or broken bracket to stop drawer sagging and misalignment. What it does:

• Holds the freezer drawer in place and supports the drawer track
• Restores proper drawer alignment for smooth opening and closing
• Helps eliminate drawer sag, catching, or uneven movement
• Works with factory mounting points to maintain intended fit

• Disconnect power before starting and remove food from the drawer area
• Remove the drawer and any trim panels to access the bracket mounting screws
• Reuse original fasteners unless specified otherwise; align bracket before tightening

This metal mounting bracket secures internal components to the appliance frame, restoring proper alignment and reducing movement. Replace a worn or damaged bracket to stop rattling and maintain stable operation. What it does:

• Provides structural support to hold panels, controls, or assemblies in place
• Prevents excess vibration and noise caused by loose parts
• Keeps components aligned for reliable mechanical operation
• Helps maintain safe clearances between moving parts

• Turn off power and unplug the appliance before beginning work
• Use appropriate hand tools; retain any original fasteners unless replacements are specified
• Inspect adjacent parts and mounting points for damage; replace if worn

This evaporator cover mounting bracket secures the evaporator cover inside the freezer compartment to keep cooling airflow and components in place. Durable metal construction replaces a broken or bent bracket to restore proper cover alignment. What it does:

• Holds the evaporator cover in position for correct airflow and protection of the evaporator coil
• Helps stop rattling or loose cover movement that can cause noise
• Restores a secure mounting point after impact or corrosion damage
• Works with the evaporator cover assembly to maintain consistent cooling performance

• High-level replacement: remove the evaporator cover to access mounting points; fasten bracket with existing screws
• Use basic hand tools; keep screws and clips organized for reassembly
• Disconnect power to the appliance before starting any repair to avoid electrical hazard

This flange strainer fits into the dishwasher sump to keep debris out of the pump assembly, helping prevent clogs and protecting the drain system. It restores proper filtering for dependable wash and drain performance. What it does:

• Screens food particles and grit before they reach the pump impeller
• Helps reduce clog-related wash failures and odors
• Prevents solids from damaging the sump and pump components
• Maintains normal draining and circulation when intact

• Disconnect power to the appliance before servicing
• Access the sump by removing the dishwasher tub access panel or lower dish rack as required by your model
• Inspect surrounding gaskets and seals; replace any damaged seals to prevent leaks
• Test for leaks and proper draining after reassembly

The Refrigerator Lower Hinge Bracket is an essential component for maintaining the proper alignment and functionality of your Samsung refrigerator door. This genuine OEM part ensures a perfect fit, matching the original specifications of your appliance. Crafted with durability in mind, the lower hinge bracket provides robust support, allowing your refrigerator door to open and close smoothly without any wobbling or misalignment. Installing this bracket helps prevent further damage to your refrigerator, enhancing its longevity and performance. The Refrigerator Lower Hinge Bracket is specifically designed for a range of Samsung refrigerator models, ensuring compatibility and easy installation. By choosing this genuine OEM part, you can be confident in the quality and reliability of your repair, restoring your refrigerator to optimal working condition. Whether youGÇÖre replacing a broken hinge or upgrading your appliance, this lower hinge bracket offers a dependable solution to keep your kitchen running efficiently.

This top-front bracket secures the appliance's top or front panel in place to keep panels aligned and stable. Replacing a damaged bracket restores proper panel fit and reduces rattling or loose trim. What it does:

• Mounts and supports the top/front panel to the appliance frame
• Prevents panel movement that can cause noise or misalignment
• Helps maintain correct door or control-panel fit where applicable
• Used when bracket is bent, cracked, or missing mounting holes

• One top-front bracket

• Disconnect power (and water, if applicable) before starting any repair
• Remove necessary trim or panels to access the bracket; retain original fasteners unless new hardware is supplied
• Align bracket and reinstall screws securely; avoid overtightening to prevent strip-out
• If other mounting hardware is damaged, replace it to ensure a secure fit

This bracket assembly secures a switch and thermal fuse used to control power and protect the appliance from overheating. It replaces a worn or failed mounting assembly to restore proper electrical safety and switch function. What it does:

• Holds the switch and thermal fuse in the correct position for reliable operation
• Allows the switch to detect door/cover position or user inputs (safe, common symptom: appliance won't start or respond)
• Provides thermal-fuse protection when overheating or overcurrent interrupts normal operation (safe symptom: appliance stops mid-cycle)
• Restores secure electrical connections when the original bracket is cracked or terminals are loose

• Always disconnect power (unplug or shut off breaker) before starting work
• Basic hand tools required; follow the appliance's service manual for exact steps
• Inspect wiring and connectors for heat damage; replace if compromised

This mounting bracket is a replacement support bracket that secures appliance panels and components, restoring proper alignment and stability so doors, panels, or internal assemblies fit and operate correctly. What it does

• Provides stable support for cabinet panels or internal components to prevent sagging or misalignment
• Restores correct panel or door alignment that can reduce rubbing, catching, or vibration noise
• Replaces cracked, bent, or missing brackets that can cause loose panels or uneven gaps
• Works where a small stamped/formed metal bracket is used to attach or support assemblies

• Disconnect power (and water, if applicable) before starting any repair
• Use basic hand tools; bracket typically fastens with screws or bolts — keep original fasteners if reusable
• Support panels while removing/installing the bracket to avoid dropped parts or pinched wiring

This door lever is the user-access handle component that lets the appliance door open and latch reliably. It replaces a damaged or broken lever to restore normal door operation and safe access. What it does:

• Provides the handle/lever action needed to open and close the appliance door
• Restores a secure latch action when the original lever is cracked, worn, or broken
• Stops sticking or slipping that can prevent the door from opening smoothly
• Helps prevent further damage to the door assembly by replacing a compromised lever

• Disconnect power to the appliance before beginning any work to avoid shock or injury
• Basic hand tools typically required; access may require removing the door or inner panel
• Inspect surrounding trim and mounting points for damage; replace additional parts if worn