Parts for Whirlpool GLS3665RS03: 02 - Burner Box, Gas Valves And Switches Parts

The Spark Module is an OEM prat for Whirlpool brand gas ranges. Within the gas control, it functions to generate high-voltage sparks igniting the standing pilot lights and burner flames. 

Causes of failure include normal wear of internal electronics from extensive temperature cycling. Contamination or damage over time also disrupts proper sparking.

Symptoms of a faulty module include: 

• Standing pilots failing to remain lit between use  
• Burners not igniting when the control knob is turned 
• Inconsistent burner output or shutdowns during cooktop usage

This Whirlpool replacement ensures temperature adjustments and cooking functions operate reliably. Compatible replacements are suitable for Whirlpool, Maytag, KitchenAid, and some Kenmore appliances as well. 
 

This burner valve controls gas flow to a single cooktop burner, restoring safe, adjustable flame control for gas ranges and cooktops. Replace a faulty valve to help eliminate weak flames, no ignition, or difficulty regulating heat. What it does:

• Regulates gas flow to one surface burner so flame size responds to the control knob.
• Commonly replaces valves that leak, stick, or fail to open/close fully.
• Addresses symptoms such as a burner that won't light, low or uneven flame, or inability to adjust heat.
• Works as the valve assembly located behind the control knob for the affected burner.

• One burner valve

• Turn off the gas supply and power to the appliance before starting work.
• Replace only with the exact part number.
• Inspect fittings and use approved gas-tight connections; check for leaks after reassembly.

This burner valve controls the flow of gas to a range or cooktop burner so the appliance lights and maintains a steady flame. Replacing a worn valve restores consistent burner operation and reliable heat control. What it does:

• Regulates gas flow to a single burner for normal ignition and flame adjustment
• Helps maintain an even, steady flame during cooking
• Commonly replaces valves that cause a burner to fail to light or to burn low/unevenly
• Addresses intermittent ignition or difficulty holding a flame

• Turn off gas supply and electrical power before attempting service
• Verify the replacement matches the original valve and install per factory instructions
• Tighten gas fittings to the correct torque and test for leaks using a soap solution (do not use an open flame)

This regulator controls and stabilizes gas pressure to the burner assembly so the appliance heats evenly and operates safely. Designed as a direct-replacement service part to restore proper gas flow and oven/burner performance. What it does:

• Regulates incoming gas pressure to the appliance's burner manifold for consistent flame and cooking temperature.
• Helps stop symptoms like uneven heating, burners that won't light steadily, or fluctuating flame height.
• Works with the range/oven's gas valve system to maintain safe, steady fuel delivery.
• Replaces a worn or faulty regulator to restore proper appliance operation.

• One regulator (single unit as shown)

• Disconnect gas supply and power before servicing.
• Handle fittings and gaskets carefully to avoid leaks.
• After installation, perform a leak test and check burner operation per manufacturer instructions.
• No special tools beyond standard hand tools and a gas-line wrench are typically required.

This wire harness routes power and signals between the appliance control and components so the unit can operate reliably. It replaces damaged or worn wiring to restore proper electrical connections and safe operation. What it does:

• Connects control board, switches, motors and sensors to distribute power and signals
• Restores lost or intermittent electrical connections that can cause no-start or erratic operation
• Replaces frayed, burned or corroded wiring that can cause shorts or component failures
• Maintains factory routing and connector fit for secure, vibration-resistant connections

• Disconnect all power (and gas if applicable) before starting any repair
• Compare connectors and wire routing to the original; install in the same path to avoid heat or pinch points
• Use proper strain relief and secure mounting points; do not splice unless specified by the manufacturer

This switch seal is a replacement gasket that helps keep moisture and debris away from the appliance's door/control switch, protecting the switch assembly and helping restore reliable door detection and operation. What it does:

• Seals the area around the door/control switch to block water, lint, and grime.
• Helps prevent intermittent trips or failures caused by moisture or foreign material contacting the switch.
• Promotes consistent switch actuation and can extend the service life of the switch assembly.
• Useful when the existing seal is cracked, torn, flattened, or missing.

• Disconnect power before servicing to avoid electrical shock.
• Access typically requires removing the door trim or control panel—follow your model's service instructions.
• Inspect the switch and surrounding area for damage or corrosion and clean before installing the new seal.