Parts for Kenmore 796.81073310 (79681073310, 796 81073310): Cabinet And Door Assembly Parts

This hinge bracket is a direct-fit replacement that secures a refrigerator door hinge to the cabinet, restoring proper door alignment and stable operation for safe, reliable use. What it does:

• Secures the door hinge to the cabinet and provides a mounting point for the hinge pin
• Supports the door weight to help maintain correct alignment and door seal
• Helps prevent door sag, uneven gaps, and rubbing during opening/closing
• Can reduce hinge noise or binding caused by a worn or damaged bracket

• Disconnect power and empty or support the door before starting; doors can be heavy and may shift during repair
• Keep original fasteners unless replacement hardware is specified by the manufacturer
• Tighten mounting screws evenly and check door alignment and gasket seal after installation
• Replace worn hinge pin or related parts at the same time for best results

This is a taptite screw used to fasten components to sheet metal or plastic in your appliance. It forms its own threads as it's driven, helping secure panels, brackets, or covers that have lost or stripped fasteners.

• Provides secure fastening in pre-formed or unthreaded holes
• Helps fix loose, rattling, or misaligned panels and covers
• Commonly used for mounting small brackets and internal trim
• Useful when an original screw is missing or stripped

• Unplug the appliance or shut off power and any water supply before service
• Keep track of screw length and location; replace like-for-like
• Start by hand to avoid cross-threading; do not overtighten
• If the original hole is damaged, assess for safe re-use or repair

The Locker Assembly is an OEM component specifically designed for LG electric dryers. Found behind the dryer door, this assembly houses door-locking mechanics. 

Causes of a bad locker can include wear and tear over time, damage due to impact, or unintentional stress on components.

Symptoms of a faulty locker assembly include:

• The dryer door not latching securely in the closed position  
• Gaps or air leaks are visible around the door seal when running
• The door is unable to stay shut on its weight  
• Loud clicking or grinding noises from the door area

This OEM LG part is also compatible with some Kenmore models.

This taptite screw fastens panels and internal components in your appliance. It forms its own threads as it's driven to create a secure hold, restoring proper fit and reducing rattles caused by loose or missing fasteners.

• Forms threads in the mating material for a tight, secure fit
• Secures covers, brackets, and assemblies during repair or reassembly
• Replace when the original screw is missing, rusted, stripped, or won't tighten
• Helps address loose or rattling panels and misaligned parts

• Disconnect power before servicing
• Start the screw by hand to avoid cross-threading; use the correct driver
• Do not overtighten; if the receiving hole is damaged, repair or replace the mating component
• Reuse any original washers/spacers in the same order if present

This safety interlock assembly secures the washer door and signals the control when it's safe to run a cycle. Replacing a faulty unit helps restore proper locking and start functions to prevent interruptions and error codes.

• Locks the washer door and confirms it is closed to allow the cycle to start
• Sends door-closed/locked status to the control throughout the cycle
• Helps prevent the door from opening during spin or when water is present
• Common symptoms: won't start, won't lock/unlock, door error (dE) messages, cycle stops mid-wash

• Disconnect power before servicing; wear cut-resistant gloves
• Access the lock at the door opening; remove the mounting screws and disconnect the harness
• Transfer connectors to the new assembly, align, and secure without overtightening
• Ensure the door strike aligns smoothly with the new lock before testing

This snap-in hole cap covers and seals an unused opening on the appliance cabinet or control panel to restore a finished look and help keep out moisture and debris. Simple cosmetic repair that prevents dirt buildup and accidental contact with interior components. What it does:

• Covers an exposed hole or access opening for a neat, finished appearance
• Helps keep out dust, crumbs and light moisture from entering the cabinet
• Reduces risk of accidental contact with interior parts through an open hole
• Restores factory look after removing a screw, plug, or accessory

• One snap-in hole cap

• Snap into the hole from the exterior until fully seated; minimal force required
• Use a plastic trim tool or small flat blade carefully if needed to pry out old cap
• Disconnect power or follow appliance-specific safety precautions before accessing internal areas
• Replace if cracked or deformed

Locker hook secures the appliance door or access panel so it stays closed during operation. Replacing a worn or broken hook restores reliable latching and prevents the door from popping open or causing noise. What it does:

• Engages with the catch or striker to hold the door/panel closed during cycles.
• Restores proper door latching and alignment for normal operation.
• Common symptoms: door won't stay closed, rattling or intermittent latching, or door popping open.
• Small replacement part used in the latch area of the cabinet or door assembly.

• Always disconnect power (and water if applicable) before servicing the appliance.
• Access the latch area by opening or removing the door/access panel per the service manual.
• Remove and save any fasteners or clips; install the new hook in the same orientation and secure all fasteners.

This outer door frame replaces the visible trim on the front of the microwave door to restore appearance and proper door alignment. It provides a finished look and helps protect the inner door assembly from damage. What it does:

• Replaces damaged, dented, or scratched outer trim for a clean, factory appearance
• Helps secure the door assembly and maintain proper door fit and seal
• Reduces light gaps and vibration caused by warped or loose outer frame
• Matches factory fit and mounting points for straightforward replacement

• One outer door frame as shown

• Use basic hand tools; support the door while removing and reinstalling to avoid dropping
• Disconnect power to the appliance before starting work
• Keep original screws and clips; replace any damaged fasteners with equivalent OEM parts
• If the inner door or latch is damaged, inspect those components and replace as needed

This replacement gasket restores a reliable seal between mating parts in your appliance. A fresh seal helps keep air, moisture, and heat where designed, supporting proper performance while reducing leaks, drafts, and rubbing noises from a worn or deformed gasket. What it does:

• Forms a tight, resilient barrier between two surfaces to prevent unwanted air or water escape
• Helps maintain proper airflow, temperature, and/or water containment as designed
• Common signs of failure: visible tears, flattening, fraying, gaps, moisture where it shouldn't be, or unusual scraping/rubbing noises
• Replace if the seal no longer sits evenly, stays in place, or shows noticeable wear

• 1 gasket

• Disconnect power; shut off water or gas supply if applicable. Allow hot components to cool.
• Wear cut-resistant gloves; internal panels and edges can be sharp.
• Access the sealing area per your model's service procedure; remove the old gasket and clean the mating surfaces.
• Seat the new gasket evenly all the way around, then reassemble and check for uniform contact.

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

This safety cover is an internal protective shield used inside the dryer to guard components and help maintain proper airflow. Replacing a cracked or missing cover helps keep wiring and moving parts enclosed for safer operation. What it does:

• Shields internal wiring and components from accidental contact
• Helps channel air and lint flow as designed
• Replaces a damaged, heat-warped, or missing cover
• Helps resolve rattling/vibration noises and visible gaps where the cover mounts

• Includes 1 safety cover

• Unplug the dryer; for gas models, shut off gas and allow the unit to cool
• Access the cover location per your model's service manual; remove panels as needed
• Position the cover correctly and secure using existing hardware/clips
• Do not operate the dryer with the cover removed or loose

This factory kit reconfigures your dryer's exhaust to exit from the side or bottom instead of the rear. It's ideal for tight installations or when the wall vent location requires an alternate exhaust path. What it does:

• Redirects the exhaust outlet to the left, right, or bottom on compatible models (orientation varies by model)
• Enables installation in closets or shallow spaces where rear venting isn't practical
• Replaces missing or damaged side/bottom vent hardware
• Helps maintain a proper metal exhaust path when relocating the dryer

• One side vent kit

• Disconnect electrical power and shut off gas supply (if applicable) before starting
• Follow the model-specific instructions supplied with the kit or in your dryer's installation manual
• Use rigid or semi-rigid metal ducting only; avoid plastic or vinyl
• After assembly, check for secure connections, no kinks, and unobstructed airflow

The Rack is an OEM part for LG dryers. This drying rack attaches securely inside the drum and remains stationary during cycles, allowing delicate items like shoes, sweaters, and hand wash clothes to air dry without tumbling or agitation.

Causes of a bad drying rack can include broken or missing retaining clips, damage to the rack surface that inhibits proper drying, or worn mounting points that cause looseness during operation.

Symptoms of a bad drying rack include:

• Items falling off or sliding around inside the dryer drum
• The rack detaching or becoming dislodged during drying cycles
• An inability to securely hold delicate fabrics and apparel without movement

This LG part is also compatible with some Kenmore models.

This parts assembly is the factory replacement service assembly that houses and connects the appliance's internal components, restoring proper electrical and mechanical function when a worn or damaged assembly causes failures. What it does

• Replaces a damaged or worn internal assembly that can cause control failures or intermittent operation
• Restores secure electrical and mechanical connections between internal components
• Helps resolve symptoms like no power to controls, erratic operation, or components not responding
• Matches OEM fit and form to maintain original performance

• Intended for technicians or experienced DIYers; disconnect power before starting any repair
• Handle with care to avoid damaging connectors, wiring, or delicate components
• Reuse existing mounting hardware unless replacements are specified
• Test appliance function after installation and secure all panels before restoring normal use