Parts for Kitchenaid KUIO18NNVS2: 01 - Cabinet Liner And Door Parts

Size: 8-18 x 1 1/4 inch.

This replacement door bin restores inside-door storage on your refrigerator so bottles, condiments and small items stay organized and secure. Durable molded plastic matches the original fit and function. What it does:

• Provides a removable shelf inside the refrigerator door to hold bottles, jars and small containers
• Replaces cracked, broken or missing door storage that no longer secures items
• Restores original storage capacity and prevents items from falling when opening the door
• Fits into existing mounting ledges or rails and snaps into place for everyday use

• Empty contents from the damaged bin before removal
• Most installations are tool-free—lift out the old bin and snap the new one into the door ledges
• Inspect door ledges for damage before installing; replace any broken mounting clips if needed
• Handle carefully to avoid sharp edges on broken plastic and follow safety precautions

This spacer positions and supports appliance components to maintain correct clearance and alignment, helping parts fit securely and reducing wear. Replace damaged or missing spacers to restore proper component spacing and quiet operation. What it does:

• Keeps panels, brackets or assemblies properly spaced to prevent rubbing and misalignment
• Helps maintain correct clearance for moving parts and seals
• Reduces vibration and noise caused by loose or shifted components
• Restores fit when a broken or worn spacer allows parts to sit unevenly

• Disconnect power before servicing; follow all safety instructions in your owner's manual
• Confirm correct orientation and placement before tightening fasteners
• Inspect surrounding parts (brackets, fasteners, mounting points) and replace if damaged

Size: 8-18 x 1/2 inch.

This exterior door panel restores the dishwasher's front appearance and protects the inner door assembly from everyday wear. A factory-style replacement that matches original color and finish for a clean, finished look. What it does:

• Replaces a scratched, dented, or faded outer door surface to improve appearance.
• Covers and protects inner door components and trim from moisture and damage.
• Helps ensure the control panel and handle area have a proper mounting surface and alignment.
• Matches original color/finish so the appliance looks consistent with the rest of the cabinet.

• One exterior door panel

• Install requires removing the door trim and possibly the inner door liner; follow for panel removal and reassembly.
• Handle and control trim may need to be transferred; only the outer panel is listed as supplied.
• Use caution supporting the door during disassembly to avoid dropping or damaging the door or hinges.
• Disconnect power and water to the appliance and follow all safety procedures before beginning repair.

This spring-style tube clamp secures flexible tubing to fittings, helping prevent leaks and maintain proper flow. It's a simple replacement that restores a firm seal on water or drain lines. What it does:

• Keeps flexible tubing firmly clamped to barbed or nipple fittings
• Helps stop or reduce leaks from loose or corroded connections
• Prevents tubing from slipping off under pressure or vibration
• Useful where a compact, spring-action clamp is required

• Disconnect power and shut off water to the appliance before replacing parts
• Use pliers to expand the clamp, position it over the tube/fitting, then release to secure
• Inspect connected tubing and fittings for damage; replace if cracked or severely corroded

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This retainer clip secures the appliance axle in place to keep rotating parts aligned and running smoothly. Replacing a worn or broken clip helps reduce noise, vibration and drivetrain misalignment for reliable operation. What it does:

• Holds the axle/shaft in position to prevent lateral movement and maintain alignment
• Prevents excessive play that can cause noise, vibration or uneven wear
• Helps keep connected components (drum/rotor/wheel) tracking correctly
• Commonly replaced when clipped, bent or missing after repair or wear

• Disconnect power before starting any repair
• Removal may require pliers or a small punch to release the old clip; reinstall by snapping into the axle groove
• Inspect mating shaft and housing for wear or damage before installing the new clip

This is a replacement screw used to securely fasten appliance panels and small components. It restores secure attachment and stops noise or loose parts caused by missing or damaged fasteners. What it does

• Holds trim, panels, brackets or components in place to prevent movement and rattling
• Restores proper alignment when a mounting screw is missing or stripped
• Helps maintain safe, stable operation by keeping parts secured
• Works wherever the original OEM screw of this part number is specified

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not over-torque; overtightening can strip threads or damage parts
• Keep small parts away from children and pets during installation

This edge guard grommet cushions and protects a cabinet or appliance panel edge to prevent wear and reduce chafing. It restores a finished look and helps keep adjacent parts from rubbing or vibrating. What it does:

• Provides a protective barrier along a sharp or exposed edge to prevent damage and wear
• Cushions panels and trim to reduce noise from vibration or movement
• Helps maintain a finished appearance where panels meet or overlap
• Can prevent metal-on-metal or metal-on-plastic contact that leads to abrasion

• One edge guard grommet

• Inspect the mounting area for damage or debris and clean before installing
• Press or slide the grommet into place along the edge until fully seated; trim excess if applicable
• If adhesives or clips are used, follow OEM recommendations for secure attachment
• Disconnect power and follow all safety precautions when working near electrical components

The Ice Maker Scoop is an OEM component specifically designed for Whirlpool ice machines. As an included accessory, it provides a sanitary and convenient way for users to fetch ice from the storage bin.

The scoop is strategically designed with an ergonomic handle and wide opening bowl shape. This facilitates easy scooping and transport of ice cubes without spillage or crumbling. Its food-safe materials maintain hygienic conditions in the storage area. 

Symptoms of a faulty scoop include:

• Cracks or breaks that compromise the scooping surface 
• Leaks or spills of ice when trying to scoop
• Sharp edges that risk cuts or scratches
• Warping or loosening of the handle attachment over time

This OEM Whirlpool scoop is also compatible with some Scotsman and Manitowoc ice machines. Replace yours today to restore safe and hygienic ice retrieval from the storage bin.
 

Size: 8-18 x 5/8 inch.

This screw grommet anchors a screw in thin appliance panels so trim, covers, or consoles stay tight. It provides a snug, vibration-damping fit where a standard screw could loosen or strip over time.

• Creates a captive insert so a screw can securely fasten to sheet metal or plastic panels
• Replaces a worn, cracked, or missing grommet to restore proper screw retention
• Helps reduce panel rattles and movement from vibration
• Typical signs of failure: screw won't tighten, panel or trim feels loose, grommet falls out

• Disconnect power and shut off gas/water as applicable before servicing
• Remove the screw and lift out the old grommet; clear debris from the opening
• Press the new grommet straight into the hole until fully seated and flush
• Reinstall the screw and tighten gently to avoid deforming the grommet

Size: 8-32 x 1/2 inch.

This hinge spring is the OEM replacement tension spring that helps support and balance the oven/range door for smooth opening, controlled closing, and proper door positioning. Restores stable door movement and reduces sudden drops. What it does:

• Provides tension to the door hinge so the door opens and closes smoothly
• Helps keep the door in the intended open or partially open position
• Reduces door sag, slipping, or sudden closing
• Can stop noisy or uneven hinge movement caused by a worn spring

• Disconnect power to the appliance before starting any repair.
• Use gloves and eye protection; springs are under tension and can snap back.
• Follow the manufacturer's removal/installation steps — you may need to partially or fully remove the door to access the hinge spring.

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

This front grille is the exterior trim piece that covers and protects the lower front of an 18-inch built-in ice maker, restoring appearance and allowing proper airflow. It replaces a cracked, faded, or damaged grille to keep the unit looking finished. What it does:

• Covers the ice maker's lower front opening and provides a finished appearance
• Protects internal components from debris while allowing ventilation
• Helps prevent drafts and keeps the trim line sealed and tidy
• Common symptom: grille is cracked, broken, loose, or discolored

• Designed for drop-in or snap-fit replacement at the front of the ice maker;
• Remove power to the appliance and empty nearby ice/water before beginning service
• Use basic hand tools; avoid excessive force to prevent breaking surrounding trim

Size: 8 x 1-1/4 inch.

This lower stainless steel panel replaces the damaged or worn kick/toe area on the appliance to restore appearance and protect components under the unit. Durable finish matches the appliance's exterior for a clean, professional look. What it does:

• Covers and protects lower cabinet/under-oven components from debris and spills
• Restores a finished, seamless exterior when the original panel is dented, scratched, or missing
• Helps reduce drafts under the appliance by closing the access opening
• Provides a clean, corrosion-resistant surface for easier cleaning and maintenance

• Disconnect power to the appliance before attempting removal or installation
• Remove trim/kickplate or front access screws as required to access mounting points
• Handle edges carefully to avoid cuts; stainless panels can be sharp
• Use the factory fasteners and alignment

This genuine fastener secures panels and components on compatible appliances so panels and parts stay safely in place during use. Small and simple, it restores proper fit where a missing or damaged screw causes loose or rattling parts. What it does:

• Fastens panels, brackets, or small components to restore secure attachment
• Helps eliminate loose panels, rattling, or misaligned parts caused by missing hardware
• Used wherever the OEM screw is specified for a clean, factory-fit repair
• Matches the original thread and head style for proper engagement

• Always disconnect power and water before starting appliance repairs
• Use the correct screwdriver or driver bit to avoid stripping the head
• Hand-start threads, then tighten snugly — do not overtighten to avoid damaging parts
• Keep small parts away from children and pets during repair

This is a replacement screw used to securely fasten appliance panels and small components. It restores secure attachment and stops noise or loose parts caused by missing or damaged fasteners. What it does

• Holds trim, panels, brackets or components in place to prevent movement and rattling
• Restores proper alignment when a mounting screw is missing or stripped
• Helps maintain safe, stable operation by keeping parts secured
• Works wherever the original OEM screw of this part number is specified

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but do not over-torque; overtightening can strip threads or damage parts
• Keep small parts away from children and pets during installation

This replacement screw secures appliance panels, brackets, and components to the cabinet or chassis. The #8-15 x 1/2 in. size restores a snug, reliable hold when original hardware is missing, stripped, or corroded.

• Fastens panels, brackets, and trim to the appliance cabinet or chassis
• Helps reduce rattling, vibration, or looseness caused by missing/stripped hardware
• Restores proper alignment of parts that have shifted due to loose fasteners
• Size/spec: #8-15 thread, 1/2-inch length; use where this size is specified

• Disconnect power and shut off gas/water supplies before servicing
• Replace one screw at a time to maintain alignment of parts
• Start threads by hand to prevent cross-threading; do not overtighten
• Use a matching driver/bit type for the screw head used in your appliance

This replacement access panel cover restores a finished appearance and protects internal components from dust and accidental contact. Fits in the original mounting location to keep the appliance safe and secure. What it does:

• Shields internal parts from dirt and debris to help maintain proper operation
• Hides wiring and mechanisms for a clean, factory look
• Prevents accidental contact with moving or electrical components
• Stops drafts and reduces rattling when the original cover is cracked or missing

• One cover

• Disconnect power before attempting any service
• Remove fasteners or clips holding the old cover, then position and secure the replacement
• Keep original screws or clips; replace only with manufacturer-recommended fasteners if needed

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.