Parts for Bosch WTMC532CUS/05: Cabinet Parts

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

The Foot is an OEM component specifically designed for select Bosch vented dryers requiring balanced tumbling motions. As an anchor point, it supports revolving drum weights during operation.

Causes requiring replacement relate to cumulative use wearing down attached glides and compromising smooth rotations. Physical damage exposing reinforcement fibers risks accelerated failure. 

Symptoms signaling the need for a new foot involve:

• Shaking or off-balanced drum movements from failed supports
• Loosened fasteners enabling unintended dislodging or displacement
• Cracked housings no longer stabilize intended weight distributions

This OEM Bosch replacement foot is also compatible with Thermador, Gaggenau and select Kenmore dryers relying on anchored rotational components. Correct installation restores intended weight balancing.
 

This Cap is a small protective closure used to cover and protect exposed openings or fittings on compatible Bosch appliances, helping keep dirt and moisture out for reliable operation. What it does:

• Covers exposed openings, ports, or fasteners to prevent debris and moisture intrusion
• Helps maintain proper alignment and protection of small components
• Stops small leaks or drips when used as a sealing closure in low-pressure areas
• Useful when the original cap is cracked, missing, or worn

• One replacement cap

• Install by snapping or pressing into place; no special tools typically required
• If the cap is near electrical components, disconnect power before replacing
• Replace if cracked or deformed to restore proper protection

The Door Hinge is an OEM part for Bosch dryers. This hinge is designed to securely attach the dryer door to the frame, allowing it to open and close smoothly while maintaining a proper seal during operation.

Causes of a bad door hinge can include regular wear and tear, damage from excessive force when opening or closing the door, or corrosion from exposure to moisture and heat.  

Symptoms of a bad door hinge include:

• The dryer door not closing properly or staying open
• Difficulty opening or closing the dryer door
• A misaligned dryer door
• Unusual noises or resistance when moving the door

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replacement mounting screw that secures panels, brackets and trim on compatible Bosch appliances. Restores proper fastening to reduce rattling, loose parts and alignment issues for safer, quieter operation. What it does:

• Secures panels, brackets, trim pieces and small appliance components.
• Replaces missing, stripped or corroded screws that allow parts to vibrate or become misaligned.
• Helps restore proper fit and reduces noise caused by loose or shifting components.
• Used wherever the original screw fastens service panels or mounting brackets.

• Disconnect power to the appliance before beginning any repair work.
• Use the correct driver bit to avoid stripping the screw head; apply firm, steady pressure.
• Do not overtighten—tighten until snug and parts are secure to avoid damaging threads or components.
• If original threads are damaged, inspect mating component and replace damaged parts or use appropriate thread repair methods.

This replacement access cover protects internal components and restores a finished appearance to the appliance. It helps keep wiring and small parts shielded from moisture, dirt, and accidental contact. What it does

• Shields internal components and wiring from debris and accidental contact
• Restores the appliance's finished appearance where the original cover was cracked or missing
• Helps reduce rattling caused by a loose or damaged cover
• Can prevent moisture and small-parts ingress that may lead to further damage

• One cover

• Disconnect power and water supply before beginning any repair
• Remove any surrounding panels or fasteners to access the damaged cover; keep track of screws and clips
• Align tabs or screw holes and reinstall with the original hardware; do not force or bend the part

The Door Latch is an OEM part for Bosch dryers. It securely fastens the dryer door closed during operation to prevent heat loss and ensure optimal drying performance. 

Causes of a bad latch include wear and tear over time, damage due to repeated use, or failure of the latch mechanism. 

Symptoms of a bad door latch include:

• The door not fully closing or latching in the locked position
• The door popping or coming open during a cycle  
• Decreased drying efficiency due to air leaks
• Safety issues from an unsecured door

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Screw is an OEM part for Bosch gas cooktops and ranges. It anchors the surface burner head assembly onto the cooktop surface.

Causes can be stripped threads or overall wear from repeated heating/cooling cycles. Exposure to cooking spills or impacts may also deteriorate the screw head over time.

Symptoms of a bad burner head screw include:

• A burner detaching from the cooktop surface entirely
• Excess movement or instability of burner heads when in use
• Gas leaks reported around the burner head connection points

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.