Parts for Maytag MZC3122FW01: Cabinet Parts

This door hinge secures and allows smooth pivoting of a refrigerator door so it opens and closes correctly. It restores proper door alignment and helps maintain a tight seal to preserve cooling performance. What it does:

• Supports the weight of the door and provides a stable pivot point
• Keeps the door aligned to prevent rubbing, gaps, or uneven closing
• Helps the door seal fully to prevent warm air leaks and temperature loss
• Commonly replaced when the door sags, sticks, or makes noise during operation

• One door hinge assembly

• Disconnect power to the appliance before beginning any repair
• Support the door while removing and installing the hinge to prevent injury or damage
• Use factory mounting hardware; tighten fasteners securely but avoid over-torquing
• Check hinge pins and mounting surfaces for wear

This mechanical thermostat is the appliance's temperature control. It senses internal temperature and opens or closes its electrical contacts to cycle the system, helping the unit reach and maintain the setting you select for consistent performance.

• Regulates temperature by switching power to the cooling or heating circuit as needed
• Helps prevent overcooling/overheating and unstable temperatures
• Common symptoms: runs constantly or won't start, temperature too warm or too cold, short-cycling, no response to knob/setting changes
• Visual damage, burnt terminals, or a thermostat that fails continuity tests indicate replacement

• Disconnect power before servicing
• Document wire locations; transfer wires one at a time and secure all connections
• If your unit uses a sensing bulb/capillary, route and secure it exactly as original; do not kink or sharply bend it
• Verify correct mounting and smooth knob/shaft movement, then restore power and test

This is a replacement machine screw used to secure interior and exterior appliance panels and components. It restores proper fastening to reduce vibration and keep parts aligned for reliable operation. What it does:

• Secures panels, brackets, or small components to the appliance frame
• Stops rattling or movement caused by a missing or stripped screw
• Helps maintain correct alignment of control panels and trim pieces
• Works as a direct replacement when the original screw is lost or damaged

• One screw

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten to firm hand pressure; do not overtighten to prevent thread or part damage
• Disconnect power to the appliance before accessing internal components
• If fasteners or mounting holes are damaged, replace with the appropriate hardware.

This factory fastener secures panels, trim, or brackets on your appliance. Replacing a missing or stripped screw restores a snug, rattle-free fit and keeps components aligned for proper operation and a clean, finished appearance.

• Fastens exterior panels, trim pieces, or internal brackets to the appliance chassis
• Replaces lost, damaged, or stripped hardware
• Helps prevent vibration, rattling, and gaps between parts
• Common signs you need this screw: missing hardware, loose or misaligned panel/trim, stripped head or threads

• Disconnect power before servicing; also shut off the gas supply
• Use the correct driver; start the screw by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping or cracking adjacent parts
• Repair or replace the mounting point before installing

This defrost drain adapter funnels melted defrost water from the evaporator area into the refrigerator's drain channel, helping prevent water pooling and evaporator-area leaks. A simple replacement to restore proper drain flow. What it does:

• Directs defrost meltwater into the cabinet drain to prevent pooling under the evaporator.
• Helps stop water from leaking into the refrigerator or freezer compartment.
• Can reduce odor and residue caused by standing water in the drain area.
• Fits the drain/chest drain opening and mates to the cabinet drain tubing.

• Disconnect power to the appliance before starting any repair.
• Access typically requires removing interior panels or the evaporator cover—keep screws and fasteners organized.
• Clean the drain channel and line of any ice or debris before installing the adapter to ensure proper flow.
• Reconnect power and test by pouring a small amount of warm water into the evaporator area to ensure the drain is routing properly.

This replacement door lock key restores the ability to lock and unlock the factory door lock on select appliances. Ideal when the original key is lost or damaged, helping you secure contents and access your unit with confidence. What it does:

• Engages the lock cylinder to lock or unlock the door
• Restores security when the original key is lost, bent, or broken
• Helps prevent unintended door opening during storage or transport
• Common symptoms: cannot lock/unlock, missing key, key no longer turns the lock

• Door key

• Confirm this key matches the lock used on your model by checking your model's parts list
• Insert fully and turn gently; do not force a jammed lock
• If the lock will not operate, inspect the lock cylinder for damage or replacement needs
• Keep spare keys in a safe place and out of reach of children

This door lock is the latch assembly that secures the appliance door during operation so cycles start and run safely. It replaces a worn or broken latch to restore proper door closing and locking. What it does:

• Secures the door so the appliance can start and complete cycles
• Prevents the door from opening during operation for user safety
• Stops operation or shows a door error when the latch fails or doesn't engage
• Helps restore proper door alignment and closure when replaced

• One door lock / latch assembly

• Disconnect power (and gas if applicable) before starting any repair
• Basic hand tools typically required; handle the latch and mounting tabs carefully
• Verify door alignment and actuator engagement after installation

This replacement name plate restores the appliance's identification label so model and serial information is legible and the exterior looks complete. It's a simple cosmetic and identification part that helps owners read key appliance info. What it does

• Replaces a faded, damaged, or missing identification label
• Restores readable model/serial/manufacturer details for service and registration
• Improves cosmetic appearance where the original label is worn or peeled
• Helps prevent confusion when ordering parts or scheduling repairs

• One replacement name plate

• Clean and dry the mounting surface thoroughly before installing
• Align carefully and press firmly if adhesive-backed; use the original fasteners if applicable
• Handle by the edges to avoid transferring oils or smudges to the label

This replacement cover is an access panel that protects internal components and helps keep dust and lint out of the appliance. It restores the finished appearance and secures the area for safe operation. What it does:

• Covers and protects internal parts and wiring from debris and accidental contact
• Helps reduce lint and dust buildup that can affect performance
• Provides a finished exterior surface after service or repair
• Secures mounting points so internal components stay in place during operation

• Disconnect power (and gas if applicable) before starting any repair
• Basic hand tools usually required; follow OEM disassembly/reassembly steps
• Handle carefully to avoid scratching painted surfaces and to protect clips/tabs
• Replace damaged clips or fasteners to ensure a secure fit