Parts for Whirlpool WRF992FIFH00: 02 - Cabinet Parts

The Leveling Leg is an OEM replacement part for Whirlpool refrigerators. It is one of four legs situated internally at the base corners for proper tilt positioning. It raises or lowers each leg independently to stabilize units on uneven kitchen floors.

Causes of replacement consist of wear from continual torque required during positioning processes. Thread damage or corrosion buildup attributable to floor locations over extended use necessitates periodic renewal as well.

Symptoms involve:

• Doors that fail to align or seal completely during open-close cycles
• Noisy imbalances traced to feet contacting floor surfaces
• Appliance rocking is unable to be remedied through existing leg corrections

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

This door hinge secures and allows smooth pivoting of a refrigerator or freezer door so it opens and closes correctly, helping maintain a proper seal and consistent cooling performance. What it does

• Supports the door weight and provides a stable pivot point for opening and closing
• Keeps the door aligned to ensure the gasket seals properly and reduce cold-air loss
• Helps prevent door sag, rubbing, and uneven wear that can cause noise or poor sealing
• Replaces a worn, bent, or damaged hinge to restore proper door movement

• One door hinge

• Installation requires removing the door or supporting it to avoid damage
• Use proper tools and torque; tighten fasteners securely but avoid over-torquing
• Disconnect power to the appliance before working if panels or wiring must be removed
• If the hinge mounts use separate screws or bushings, transfer existing hardware unless OEM kit specifies otherwise

This replacement screw fastens appliance components securely in place. Use it to replace missing, stripped, or corroded hardware so panels, brackets, and covers stay aligned and rattle-free.

• Secures parts such as panels, brackets, covers, or internal assemblies
• Restores alignment and helps eliminate vibration or rattling from loose hardware
• Replaces lost, rusted, or damaged screws during service
• Maintains safe, stable operation by keeping components tight

• Disconnect power before service; if applicable, also shut off water and/or gas
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver bit to prevent stripping the head

This replacement screw fastens appliance components to restore secure connections and reduce vibration or rattling. Use it when panels, brackets, or assemblies are loose or moving. What it does:

• Secures panels, brackets, and small appliance parts to prevent movement
• Restores proper alignment for doors and trim that shift from loose hardware
• Helps eliminate vibration noise caused by loose fasteners
• Works with assemblies that use standard machine/sheet-metal screws

• Disconnect power or gas supply before servicing the appliance
• Use the correct driver bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or damage parts
• Inspect surrounding components and replace any damaged clips or hardware as needed

Color: Black
 

Color: Grey
 

Color: Black

Color: Grey

The Hinge Door is an OEM part for Whirlpool refrigerators. It attaches the refrigerator door securely while allowing smooth opening and closing. Reinforced metal hinges withstand heavy doors with precision balance.

Over the years, excess force from heavy loads or clumsy handling can misalign hinges. Causes of a bad hinge include stripped screws, bent barrels, or worn bushings letting doors droop or stick.

Symptoms of a bad hinge include:

• Door doesn't close or seal properly
• Difficulty opening/closing the refrigerator door 
• Door is crooked or sits unevenly
• Noise or grinding felt/heard from hinges

This Whirlpool OEM hinge ensures proper door function. Its durable construction maintains dependability and refrigerator efficiency. Compatible also with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, select Kenmore models.

This black plastic corner cover replaces a damaged or missing exterior trim piece to restore the appliance's finished appearance and protect internal edges from dirt and wear. Fits the factory location and matches original styling. What it does:

• Covers and protects the appliance corner or trim area from chips, scuffs, and debris.
• Restores a clean, finished look where the original corner piece is cracked, broken, or missing.
• Helps keep moisture and grime from reaching internal seams at the corner.
• Matches the original color and shape to maintain the appliance's aesthetic.

• Install with the appliance powered off and unplugged for safety if cover removal exposes wiring.
• Remove any broken fragments and clean the mounting area before installing the new cover.
• May snap or screw into place depending on model; keep fasteners from the original cover for re-use.

This cover corner replaces a missing or damaged corner trim piece to restore the refrigerator's interior/exterior finish and help keep shelves and bins seated properly. It provides a clean, finished look and protects edges from wear. What it does:

• Replaces the corner trim/filler that covers panel edges or joins interior liners
• Helps keep adjoining panels, shelves or bins aligned and reduces gaps
• Restores appearance after chipping, cracks or impact damage

• Designed for drop-in or snap-on installation; verify fit against the appliance before final assembly
• Use basic hand tools; avoid excessive force which can crack plastic parts
• Disconnect power if removing interior panels or working near electrical components

This is a genuine mounting screw used to secure appliance panels and components. It provides reliable fastening to keep parts aligned and reduce vibration-related noise for safer, quieter operation. What it does:

• Secures panels, brackets, or small components to the appliance frame
• Prevents parts from loosening and causing rattling or misalignment
• Maintains proper part positioning for reliable operation
• Helps reduce vibration and noise when panels are fastened correctly

• Use the correct driver and size to avoid stripping the head
• Tighten until snug; do not overtighten which can strip threads or crack plastic
• Disconnect power before servicing electrical appliances to avoid shock
• If a screw is corroded or damaged, replace all similar fasteners in that area for best results

Replacement screw that secures panels, brackets, and other components inside your appliance, keeping assemblies tight and aligned. Replace missing or stripped hardware to eliminate looseness, reduce vibration, and restore a solid, factory-fit hold.

• Fastens panels, brackets, trim, or internal components
• Helps maintain alignment and reduce rattling/vibration
• Replaces missing, loose, rusted, or stripped hardware
• Common signs: stripped head/threads, loose panel, buzzing/rattling noises

• Disconnect power before service; shut off gas/water if applicable
• Match to the original screw; start threading by hand to avoid cross-threading
• Use the correct driver size to prevent stripping
• Tighten snugly; do not overtighten. If it won't hold, inspect the receiving hole/clip

Replacement screw that secures panels, brackets, and other components inside your appliance, keeping assemblies tight and aligned. Replace missing or stripped hardware to eliminate looseness, reduce vibration, and restore a solid, factory-fit hold.

• Fastens panels, brackets, trim, or internal components
• Helps maintain alignment and reduce rattling/vibration
• Replaces missing, loose, rusted, or stripped hardware
• Common signs: stripped head/threads, loose panel, buzzing/rattling noises

• Disconnect power before service; shut off gas/water if applicable
• Match to the original screw; start threading by hand to avoid cross-threading
• Use the correct driver size to prevent stripping
• Tighten snugly; do not overtighten. If it won't hold, inspect the receiving hole/clip

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

This genuine replacement door latch micro switch restores reliable door sensing and latch function so the appliance only runs when the door is fully closed. Designed to match the original fit and electrical connections. What it does

• Detects door closure and signals the appliance control to start or stop cycles
• Prevents operation when the door is open to help ensure safe operation
• Stops intermittent starts or unexpected pauses caused by a worn switch
• Restores consistent electrical contact for dependable performance

• One replacement door latch micro switch

• Disconnect power before inspecting or replacing the switch to avoid shock hazard
• Verify correct orientation and secure all connectors to ensure proper function
• Handle the switch and wiring gently; replace any damaged wires or terminals

This rubber grommet cushions and protects a mounting or wiring pass-through, helping reduce vibration and prevent chafing where parts or wires pass through a panel. It's a simple replacement that restores a secure, quiet fit. What it does:

• Provides a protective barrier around openings to prevent wire and component abrasion
• Cushions panels or components to reduce noise and vibration
• Helps maintain proper alignment of mounted parts
• Commonly replaced when torn, flattened, or allowing rubbing/metal-to-metal contact

• One rubber grommet as shown

• High-level replacement — access to the panel or opening is required
• Inspect surrounding fasteners and wiring for damage while replacing
• Use basic hand tools; avoid stretching the grommet excessively during installation
• Disconnect power to the appliance before working in areas with wiring or motors

This replacement valve cover protects and secures the washer's inlet valve assembly, helping keep water and wiring contained and reducing risk of leaks or damage. It restores the valve area's original shielding and fit. What it does:

• Covers and protects the water inlet/valve area from splashes and debris
• Helps keep valve wiring and connections properly routed and contained
• Can stop water spray from a damaged or misaligned valve area
• Restores correct mounting/fit to prevent valve movement and noise

• One replacement valve cover

• Disconnect power and shut off water before starting any repair
• Basic hand tools are typically required; access may require removing the top or control panel
• Align cover tabs and secure fasteners until snug; do not overtighten
• Inspect nearby seals, hoses and valve connections while accessible

This replacement vent directs airflow from the appliance's blower to the outside or into the vent duct, helping maintain proper exhaust and drying performance. Fits where the OEM vent assembly is required for safe, efficient operation. What it does:

• Channels exhaust air from the appliance to the duct system to prevent backflow and moisture buildup.
• Restores proper ventilation when a cracked, damaged, or missing vent causes poor airflow or noisy operation.
• Helps reduce lint and debris escape into the cabinet area by providing the correct outlet path.
• Supports normal drying/heating performance by maintaining intended airflow routing.

• 1 vent

• Turn off and unplug the appliance (or shut off power at the breaker) before beginning any work.
• Remove any surrounding panels or access covers to reach the vent; follow manufacturer service instructions for disassembly.
• Inspect mating ductwork and seals; replace damaged ducts or use approved clamps/adhesive to ensure an airtight connection.

The Hinge Bushing is an OEM component specifically designed for Whirlpool refrigerator doors. It is a circular bearing and support component that promotes smooth door swinging. The bushing fits within hinges to reduce friction and prevent premature wear.  

Causes of compromised hinge bushings can be years of door opening compressing the bushing material. Exposure to moisture also contributes to cracked, pitted or damaged bushings failing to guide doors effortlessly.

Symptoms of failing hinge bushings include:

• Stiff or resistant door movement requiring extra effort  
• Noisy hinges or grinding sounds due to metal-on-metal contact
• Misaligned or sagging doors unable to fully latch or seal
• Premature wear of connecting hinge parts forcing early replacement

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This replacement washer is a small ring used with a screw or nut in your appliance to distribute load and maintain proper spacing. Replacing a worn or missing washer helps keep assemblies tight, aligned, and quiet.

• Sits under a fastener head or nut to spread load and protect the mating surface
• Maintains correct spacing/alignment within the specified assembly for your model
• Helps resist loosening from vibration
• Common signs it's needed: missing/damaged washer, loose or wobbly component, rattling or metal-on-metal noise

• Disconnect power; shut off water supply if applicable
• Note the order/orientation of hardware before removal; take a reference photo
• Hand-start threads to avoid cross-threading; place washer in the same position as removed
• Tighten fastener to manufacturer guidance; do not overtighten