Parts for Kitchenaid 5KSM193ADEVB5: Color Variation Parts

This housing is the outer cabinet component that protects and supports internal appliance parts, keeping wiring and assemblies secure for reliable operation. It restores proper fit and helps prevent loose components or rattling. What it does:

• Protects internal components and wiring from damage and debris
• Provides structural support and correct alignment for mounted parts
• Helps reduce noise from loose or damaged internal assemblies
• Can cause fit, sealing, or operational issues if cracked or distorted

• Disconnect power before servicing to avoid electric shock.
• Handle carefully; edges may be sharp and fasteners may be under tension.
• Basic hand tools typically required; follow the appliance service manual for disassembly order.
• Replace any damaged fasteners or gaskets to ensure proper fit and sealing.

This housing is the main outer cabinet section that supports internal components and helps direct airflow and protect the appliance. Replacing a damaged housing restores proper fit, reduces noise from loose panels, and prevents debris entry. What it does:

• Provides structural support for internal parts and mounting points
• Protects internal components from dust, moisture, and physical damage
• Helps channel airflow for proper operation and venting
• Reduces rattles and vibration caused by cracked or warped panels
• Prevents sharp edges and gaps that can catch clothing or debris

• Disconnect power before beginning any repair to avoid shock or injury
• Basic hand tools are typically required; follow the service manual for panel removal and reassembly
• Handle sharp edges carefully and wear gloves to protect your hands

This housing is the replacement cabinet housing that supports and protects internal appliance components, restoring proper fit and appearance. It helps keep internal parts secure and maintains correct panel alignment for safe operation. What it does:

• Provides a rigid mounting surface for controls, assemblies and wiring
• Protects internal components from dust, moisture and impact
• Maintains panel alignment to reduce vibration and rattling
• Restores correct clearance and fit when an outer cabinet is cracked or warped

• Disconnect power and water before beginning any repair
• Basic hand tools required; mounting screws or clips must be reused
• Handle edges carefully to avoid cuts; wear gloves and eye protection
• Verify fit and orientation with parts diagram before final assembly

This housing is the replacement cabinet component that helps protect internal dryer components and maintain proper airflow and alignment. Replacing a damaged housing restores panel fit and helps prevent debris from reaching internal parts. What it does:

• Forms the external or internal cabinet surface that supports and protects internal components
• Helps maintain proper airflow and component alignment for normal operation
• Commonly replaced when cracked, warped, or broken from impact or wear
• Can reduce rattles, gaps, and debris intrusion when installed correctly

• Refer to your model's service manual for disassembly and reassembly instructions
• Disconnect power (and gas, if applicable) before starting any repair
• Handle edges carefully; wear gloves to avoid cuts and protect finishes
• Compare the replacement to the original part for fit before final installation

This replacement housing restores the appliance's structural cabinet where internal components mount, helping secure parts and reduce vibration. Use this housing to replace cracked, warped or damaged cabinet sections that affect fit and stability. What it does:

• Provides a rigid mounting surface for motors, controls and other internal parts
• Helps maintain proper alignment to reduce vibration, noise and rubbing
• Replaces cracked, broken or distorted cabinet sections that can allow parts to shift
• Prevents moisture and debris from reaching internal components when intact

• One housing cabinet as shown

• Disconnect power and water before starting any repair
• Basic disassembly of exterior panels may be required; retain screws and brackets
• Handle edges carefully — plastic and metal housings can have sharp edges

This housing is the outer casing that supports and protects the washer's internal tub and components, restoring structural stability and helping contain water and vibration for reliable operation. What it does:

• Supports the inner tub and motor assembly to maintain proper alignment during cycles
• Protects internal components from debris and water exposure
• Helps reduce vibration and rattling caused by a damaged or cracked cabinet
• Can stop or reduce leaks when a compromised housing allows water to escape

• One housing

• High-level replacement; access requires disassembling the washer cabinet — follow the OEM service manual
• Disconnect power and water supply before starting work to avoid shock or flooding
• Use proper tools and fasteners; inspect adjacent seals and mounts and replace if worn

This housing is a direct-fit replacement housing piece that restores the appliance's exterior support and alignment. It helps maintain proper component positioning and prevents gaps or interference with adjacent panels. What it does:

• Provides structural support for front and/or control-area components
• Keeps internal parts aligned to prevent rubbing or noise
• Restores correct gap and seal between panels for safe operation
• Helps eliminate vibration-related movement and wear

• One housing

• Verify power is disconnected and appliance is fully isolated before starting
• Handle edges carefully; wear gloves to avoid sharp sheet-metal contact
• Use OEM fasteners and follow manufacturer torque guidance where specified

This main cabinet housing provides the structural enclosure that supports and protects internal components, restoring the appliance's original fit and finish. It helps keep parts aligned and shields circuitry and mechanisms from damage. What it does:

• Replaces a damaged or cracked main housing to restore structural integrity and proper component alignment
• Helps reduce vibration and noise caused by loose or broken enclosure parts
• Protects internal wiring, controls, and mechanical components from moisture and debris
• Restores correct mounting points for panels, latches, and internal assemblies

• One main housing

• Disconnect power and, if applicable, gas and water supplies before starting any repair
• Basic hand tools are typically required; some panels or components may need to be removed for access
• Follow OEM service instructions for proper alignment and fastener torque to ensure safe operation

This genuine replacement housing restores the appliance's outer case alignment and provides a secure mount for internal components, helping maintain safe operation and proper fit. Ideal when the original housing is cracked, warped, or damaged. What it does

• Replaces a damaged or cracked outer housing to stop rattling or loose panels
• Restores proper alignment and support for internal components
• Helps prevent debris and moisture from reaching internal parts
• Reduces vibration noise caused by a broken or misshapen housing

• One replacement housing

• Recommend disconnecting power before starting any repair
• Some disassembly of exterior panels or controls may be required; keep fasteners organized
• Inspect adjacent components and gaskets during install; replace if damaged

This replacement housing restores the appliance's outer support and protects internal components from damage. It provides a stable mounting surface so controls and assemblies stay secure and aligned for reliable operation. What it does:

• Replaces a cracked, broken or warped outer housing that lets internal parts move or rub
• Protects wiring and controls from exposure and damage
• Provides the mounting surface for adjacent panels and assemblies to prevent misalignment
• Helps eliminate vibrations, rattles or air leaks caused by damaged structure

• Disconnect power before beginning any repair; follow manufacturer safety instructions
• Basic hand tools (screwdrivers, nut drivers) are typically required; some disassembly of surrounding panels may be needed
• Handle carefully to avoid scratching painted surfaces and to align mounting tabs during reassembly
• If fasteners or clips are damaged, replace them to ensure a secure fit

This housing is the outer case panel that protects and supports internal components, restoring proper fit and appearance to the appliance. It provides structural support and shields wiring and mechanisms from dirt and damage. What it does:

• Replaces a cracked, warped or damaged outer housing to restore proper alignment and enclosure
• Keeps internal components protected from dust, moisture and impact
• Helps reduce rattling or vibration caused by a loose or broken housing
• Restores the appliance's exterior fit and finish for safe operation

• One housing

• Disconnect power (and water, if applicable) before starting any repair
• Remove trim and access panels as needed; retain fasteners for reassembly
• Handle edges carefully to avoid cuts; use proper tools and support the housing during removal/installation

This replacement cover protects and secures internal components and wiring, restoring a finished appearance and helping prevent debris intrusion. It's a like-for-like exterior housing piece used on compatible Whirlpool appliances. What it does

• Covers and protects internal electronics, terminals, and wiring from dust and accidental contact
• Restores the appliance's finished exterior where the original cover was missing or damaged
• Helps maintain proper airflow paths and component positioning when installed correctly
• Can reduce vibration-related noise by keeping parts secured and enclosed

• One cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal/installation usually requires removing a few screws and lifting the old cover off; keep fasteners for reassembly
• Handle edges carefully; use gloves to avoid cuts and protect painted surfaces

A replacement trim panel that restores the appliance's exterior finish and protects internal components from dust and debris. Helps maintain a clean look and keeps internal parts shielded after repair. What it does

• Acts as the exterior trim/cover over the appliance opening, preventing debris and lint from entering internal areas
• Protects switches, controls and internal wiring from accidental contact and damage
• Restores proper fit and finish when the original cover is cracked, warped or missing
• Stops rattling or gaps caused by a broken or loose cover

• Only install with power disconnected to avoid electrical shock
• Requires removal of adjacent panels or fasteners for access; use appropriate hand tools
• Handle carefully to avoid scratching the finish; align tabs and fasteners before tightening
• If fasteners or clips are damaged, replace them to ensure secure fit

Color: Onyx black

This cover is a replacement access panel that protects internal components and restores the appliance's exterior appearance. It keeps wiring and controls shielded while maintaining a clean, finished look. What it does:

• Shields control components and wiring from dust, spills, and accidental contact
• Restores damaged or missing exterior panels for a finished appearance
• Helps maintain proper airflow and component clearance by covering openings
• Can reduce rattles or vibration by replacing a loose or broken panel

• One replacement cover

• Disconnect power (and gas or water if applicable) before starting any repair
• Basic hand tools are typically required; follow the appliance's service manual for specific steps
• Handle edges carefully; align tabs/fasteners before securing to avoid damage
• Replace worn fasteners or clips to ensure a secure fit

A factory-matched Almond crème touch-up paint bottle to restore small chips, scratches, and worn spots on Almond-finish appliances. Helps blend blemishes into surrounding finish for a cleaner, more consistent look. What it does:

• Provides color-matched coverage for small surface chips and scratches on Almond-finish appliances
• Restores appearance without replacing large panels or trim
• Helps hide everyday wear and minor cosmetic damage
• Dries to a durable finish that blends with factory color

• One (1) bottle of Almond crème touch-up paint

• Shake well before use and test on an inconspicuous area first
• Clean and dry the surface thoroughly; remove loose paint and grease
• Apply sparingly in thin coats, allowing recommended drying time between coats
• Use in a well-ventilated area and follow all safety label instructions; wear gloves and eye protection

Color: White

This planetary gear assembly transfers motor torque through the transmission to drive the agitator/drum, restoring proper mechanical motion. Replaces a worn or damaged planetary to reduce grinding, slipping, or no-agitation symptoms and improve drivetrain reliability. What it does:

• Meshes with the transmission sun gear to convert motor rotation into the correct output for the agitator/drum
• Restores normal agitation/rotation when original gears are worn, broken, or skipping
• Helps eliminate grinding, clunking, or intermittent movement caused by damaged internal gears
• Works as a direct-fit replacement when the original planetary gear has failed

• Refer to the appliance's service manual or exploded parts diagram for correct disassembly and reassembly steps
• Disconnect power and water (if applicable) before beginning repairs to avoid shock or injury
• Inspect surrounding gears, bearings, and seals; replace any additional worn components to prevent premature failure
• Use appropriate tools and torque specs;

This planetary gear assembly drives the washer's agitator/spin mechanism to transfer motor motion into drum movement, restoring smooth agitation and spin action. Designed to fit as the washer's internal gearing component for reliable operation. What it does:

• Converts motor rotation into the agitator/drum motion for effective washing and spinning
• Replaces worn or damaged gears that can cause noisy operation or grinding sounds
• Helps correct slow, intermittent, or no-agitation and no-spin symptoms when gearbox failure is present
• Works as the internal gearset that mates with the transmission/agitator components

• One planetary gear assembly

• Disconnect power and water before beginning any repair
• Requires partial disassembly of the washer cabinet and access to the transmission/agitator area
• Inspect related parts (agitator, drive coupling, transmission) for wear and replace as needed

Color: Almond creme

This planetary gear assembly transfers motor motion to the appliance's drive mechanism, restoring smooth rotation and normal operation. It replaces a worn or damaged planetary component to reduce noise and restore consistent drive performance. What it does:

• Transfers motor torque through the gear train to the driven component for proper operation
• Replaces worn or damaged gears that can cause grinding, clunking, or loss of drive
• Helps stop intermittent or failed agitation/spin caused by stripped or broken gear teeth
• Restores correct gear engagement to reduce excessive noise during operation

• One planetary gear assembly

• Disconnect power and water before starting any repair
• Some disassembly of the gearcase or transmission may be required; follow the OEM service manual
• Inspect surrounding seals, bearings, and fasteners; replace any damaged components
• Use proper tools and torque values

Color: White

This grille control surface assembly provides the finished front trim for the appliance control area and restores a clean, secure fit and appearance. It replaces a cracked, damaged or loose control-area grille to improve panel alignment and aesthetics. What it does

• Covers and protects the appliance control area while providing the finished exterior appearance
• Restores proper fit and alignment when the original grille is cracked, bent, or broken
• Helps keep moisture and debris away from underlying controls and wiring
• Matches Onyx black finish for a consistent look with the rest of the appliance

• Disconnect power to the appliance before beginning any repair
• Basic hand tools (screwdriver, possibly trim tool) are typically required for removal and reattachment
• Align tabs and screw holes carefully to avoid cracking the trim during installation
• Replace damaged internal fasteners or mounting clips to ensure a secure fit

This direct-drive gearcase converts the washer motor's power into the agitation and spin motions. Replacing a worn gearcase restores normal drive function so the washer can agitate and spin as intended. What it does

• Transfers motor rotation to the agitator and spin basket for wash and spin cycles
• Worn or damaged gear teeth can cause no agitation or no spin
• Damaged gearcase may produce loud grinding, clunking, or unusual noises during operation
• Failure can cause intermittent drive or loss of drive in one or both cycles

• Disconnect power and water before starting any repair to prevent shock or flooding
• Drain the washer and secure the tub/agitator before removing components
• May require removing the cabinet or access panels and supporting the drum during service

This Almond Creme color finish panel restores the original look of your appliance where the finish is worn, scratched, or mismatched. It provides a factory-style color match to keep the exterior appearance consistent. What it does:

• Replaces damaged or discolored finish panels to restore appliance appearance
• Covers scratches, chips, and worn paint on the affected area
• Matches the Almond Creme factory color to maintain a cohesive look
• Helps maintain resale value and overall visual condition

• Disconnect power to the appliance before beginning any work
• Handle panel carefully to avoid scratching the finish during installation
• Align tabs and mounting points, then secure with existing fasteners as required

This pedestal feet assembly provides the lower support and leveling for a laundry pedestal, helping keep the pedestal stable and aligned beneath the washer or dryer. Designed to restore proper support and reduce rocking. What it does:

• Replaces damaged or worn pedestal feet that cause rocking, uneven height, or instability
• Provides adjustable support to help level the pedestal on uneven floors
• Protects floors by maintaining proper pedestal alignment and preventing scraping
• Restores safe, secure support for appliances installed on the pedestal

• Follow the appliance and pedestal manufacturer instructions; have a second person or proper support to prevent tip-over when removing or installing the pedestal
• Ensure the appliance is powered off and disconnected from utilities if appliance removal or repositioning is required
• Use basic hand tools; confirm all fasteners are tightened securely after installation

This pedestle is the replacement agitator post that supports and centers the washer agitator, restoring proper agitation and load stability for top-load washers. It's a direct-fit part used during agitator assembly repairs. What it does:

• Centers and secures the agitator on the transmission shaft for effective wash action
• Helps transmit agitation motion from the transmission to the agitator
• Commonly replaced when the agitator wobbles, slips, or does not rotate properly
• Restores stable operation without requiring a full agitator or transmission replacement

• One pedestle (agitator post) as shown

• Disconnect power to the washer before beginning any repair
• Remove agitator per manufacturer instructions to access and replace the pedestle
• Use appropriate hand tools; keep fasteners organized for reassembly