Parts for Whirlpool GACP15XXMG5: Container Parts

The Trash Compactor Container Handle is an OEM replacement part designed specifically for Whirlpool trash compactors. It allows the trash compactor container to be easily pulled out. 

Color: Black

Over time, the handle may become worn out or damaged due to frequent use, mishandling, or exposure to harsh cleaning chemicals. When compromised, it may become loose, break, or lose its ability to open the container.

Symptoms of a bad Trash Compactor Container Handle include:

• Difficulty opening or closing the container
• Loose or unsteady grip
• Handle breakage or cracks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 8-18 x 1/2 inch.

This replacement container restores a secure, factory-fit compartment in your appliance. Install a new container when the original is cracked or broken to keep contents properly held and nearby parts aligned as designed.

• Provides the designated compartment to hold contents securely
• Interfaces correctly with its mounting points, guides, or adjoining parts
• Replaces cracked, warped, or broken containers that won't stay seated
• Helps prevent spills, jams, or interference with nearby components

• Disconnect power to the appliance; shut off water supply if applicable
• Wear cut-resistant gloves—damaged plastic edges can be sharp
• Move any screws, covers, or inserts from the old part to the new one
• Align tabs, tracks, or snaps and press into place without forcing

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

Size: 8 x 1/2 ab.

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

Fits 15 and 18 inch compactors. This kit is for securing the compactor bags. Kit contains a set of 4 buttons and screws.

This container roller bearing supports the trash compactor drawer as it slides on its tracks. Replacing a worn bearing restores smooth, quiet movement and helps keep the container aligned for easy opening and closing.

• Provides low-friction support so the drawer glides smoothly on the tracks
• Helps maintain proper container alignment and stability
• Reduces squeaks, grinding, and sticking during operation
• Common symptoms: drawer hard to open/close, scraping noises, binding or uneven movement, visible wear/flat spots on the bearing

• Disconnect power to the compactor before servicing
• Remove and empty the drawer to access the bearing location
• Install the new bearing in the same orientation; transfer any hardware as needed
• Inspect rollers, axles, and tracks; replace any additional worn parts for best results

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection