Parts for Jenn-Air JMW3430HS00: Control Panel Parts

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This electronic control board replaces the appliance's main console controller to restore user interface and cycle control. It manages oven/dryer functions so controls, timing, and display respond correctly during operation. What it does:

• Receives input from the touchpad/knobs and sends commands to heating, motor, and timer circuits
• Controls cycle timing, display information, and safety interlocks
• Can resolve symptoms like unresponsive controls, blank or erratic display, or failure to start cycles
• Works with the appliance's sensors and relays to coordinate normal operation

• Disconnect power (unplug or shut off breaker) before starting any work
• Handle the board by its edges and avoid static discharge; use an anti-static strap if available
• Transfer any connectors, mounts, or wire harnesses from the old board exactly as found

This power supply is the electronic control board that provides the regulated voltages and control signals needed for the appliance's user console and main controls to operate reliably. It restores proper power distribution so controls can respond. What it does:

• Converts incoming AC to the low-voltage DC used by the console and control circuitry.
• Powers display, buttons, and control relays so the appliance can receive and execute commands.
• Common symptom: blank or unresponsive display/console.
• Common symptom: intermittent or total loss of control functions, or failure to start cycles.

• Disconnect power before servicing to avoid electrical shock.
• Handle the board by its edges and avoid ESD (static) damage—use proper grounding.
• Reassemble panels and secure connectors fully; test control functions after installation.

This is a replacement 8-18 screw used to secure components in compatible Whirlpool appliances. It provides a reliable, corrosion-resistant fastener to restore proper fit and function for panels and internal parts. What it does:

• Secures panels, brackets, or small internal components where an 8-18 thread is specified
• Restores loose or missing fasteners that cause rattling, misalignment, or improper sealing
• Matches OEM thread size and head profile for a correct fit when listed for your model
• Prevents further wear or damage caused by using the wrong screw size

• One screw as shown

• Turn off and unplug the appliance before starting any repair
• Use the proper screwdriver or driver bit to avoid stripping the head
• Do not overtighten—tighten until snug and components seat without play
• Replace only where the OEM specifies an 8-18 screw to ensure proper fit

This foam seal fits between mating parts to create a tight barrier that helps prevent leaks and rattling. Replacing a worn or missing seal restores proper sealing and helps keep your appliance running quietly. What it does:

• Creates a compliant gasket between components to limit air or moisture passage
• Helps dampen vibration and reduce rattling/buzzing where parts meet
• Helps maintain proper airflow or fluid routing as designed
• Typical symptoms include leaks, condensation/frost near a joint, or new vibration noises

• One foam seal

• Disconnect power; turn off the water supply before service
• Note the original seal's routing/orientation before removal
• Clean and dry all mating surfaces; remove old foam and residue
• Install without stretching or over-compressing; ensure even contact with no gaps

Color: Stainless
 

This mounting plate secures internal components to the appliance cabinet, restoring proper alignment and support for attached parts. It's a simple, durable metal bracket that helps stop rattling and keeps assemblies stable. What it does:

• Provides a secure mounting surface for control assemblies or other internal components
• Restores correct alignment when a bracket is bent or missing
• Reduces vibration and rattling from loose or unsupported parts
• Helps prevent premature wear caused by misaligned components

• One mounting plate

• Disconnect power (and gas if applicable) before beginning any repair
• Basic hand tools are typically required; keep fasteners from the original part for reinstallation
• Handle edges carefully—metal brackets can be sharp
• Refer to your model's service manual or parts diagram for exact placement and mounting fasteners

This control panel is the appliance's main user interface that houses the buttons/touchpads and display, restoring normal control and feedback. Replace a cracked, worn, or unresponsive panel to regain reliable operation. What it does:

• Provides the user interface for selecting cycles, options, and settings.
• Routes button/touch inputs to the appliance control electronics.
• Restores visible status information when the display or indicators are damaged.
• Resolves symptoms like unresponsive buttons, missing or unreadable display, or intermittent control behavior.

• Disconnect power before starting work to avoid shock or injury.
• Handle the display/buttons carefully to avoid scratching or cracking; replace damaged clips or trim as needed.
• Verify connector type and orientation before disconnecting; do not force wiring or terminals.

This genuine replacement wire harness routes power and signals between control components to restore reliable electrical connections. It replaces damaged or worn wiring to help fix intermittent power, non-responsive controls, or component failures. What it does

• Connects control board, switches and sensors to supply power and signal paths
• Restores broken or frayed wiring that can cause intermittent operation or no power
• Provides correct factory-configured terminals and connector shapes for a secure fit
• Helps resolve symptoms like unresponsive controls, lighting or motor not operating reliably

• One wire harness (single assembly)

• Disconnect power before beginning service to avoid shock or short circuits
• Inspect connectors and routing; replace any retaining clips or grommets that are damaged
• Route harness the same way as the original to prevent chafing or pinching

This wire harness is a factory-style wiring assembly that routes power and signals between controls and components, restoring reliable electrical connections for proper appliance operation. What it does:

• Provides organized electrical connections between the control and downstream components
• Restores power and signal paths when original wiring is damaged or burned
• Can resolve symptoms such as no power to a component, intermittent operation, or blown fuses/ breakers related to wiring faults
• Protects against loose or corroded connections that cause erratic appliance behavior

• One complete wire harness assembly as shown

• Disconnect all power before starting work to avoid shock or injury
• Route the harness following OEM wire clips and harness guides; avoid pinching or contact with sharp edges or hot surfaces
• Match connector shapes and colors; ensure each connector seats fully and locks
• If insulation or connectors are damaged elsewhere, inspect and repair those areas before restoring power

The Screw is an OEM part for Whirlpool appliances. This specific screw is used in various locations within Whirlpool appliances, securing components and ensuring the stability and proper alignment of parts. It is designed to fit precisely and maintain a firm hold, contributing to the overall functionality and safety of the appliance.

Over time, screws can become worn or stripped due to regular use, corrosion, or over-tightening. 

Causes of a bad screw include wear and tear, exposure to moisture leading to rust, and over-tightening which can strip the threads.

Symptoms of a bad screw include:

• Loose or wobbly components
• Misalignment of parts
• Noise due to vibrating or loose parts
• Difficulty in securing or removing the screw

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This main wiring harness provides the factory-style electrical connection for the JA combo circuits, restoring reliable power and signal routing to the washer's control and motor assemblies. It replaces damaged or frayed wiring to help eliminate intermittent operation. What it does:

• Carries power and control signals between the machine control, motor, and related components
• Replaces burnt, pinched, or corroded wiring that can cause intermittent starts, no-spin, or error codes
• Restores secure connector fit to prevent loose connections and arcing
• Maintains factory routing and strain relief for safe, long-lasting operation

• One main wiring harness (JA combo extension) as shown

• Recommended for technicians or experienced DIYers; disconnect power and water before starting
• Inspect connectors and mounting clips during installation; secure harness away from moving parts and heat sources
• Do not splice or patch unless using proper crimp connectors and heat shrink; replace if insulation is damaged
• Run a test cycle to ensure proper operation

This mounting bracket is a replacement support bracket that secures appliance components and keeps assemblies aligned for reliable operation. It restores proper fit and helps prevent rattling or movement from loose fittings. What it does:

• Secures panels or assemblies to the appliance frame to maintain proper alignment
• Reduces vibration and rattling caused by loose or damaged supports
• Restores mounting points that prevent sagging or separation of connected parts
• Helps ensure stable operation after repairs involving removed or replaced hardware

• Follow the appliance service manual for exact location and fastener torque
• Disconnect power (and gas if applicable) before beginning any repair
• Use appropriate tools and replace any damaged screws or clips with OEM-equivalent fasteners

This wire harness is the factory-style replacement that routes power and signals between components to restore reliable electrical connections and appliance function. It replaces a damaged or worn harness to help stop intermittent faults and loss of power. What it does:

• Carries power and control signals between modules, switches, and motors
• Restores continuity when frayed wires or broken terminals cause intermittent operation
• Helps eliminate symptoms such as loss of power to components, lights or controls not responding, or blown fuses
• Maintains secure plug-and-socket connections to prevent arcing and shorts

• Disconnect power (unplug or switch off breaker) before starting any repair
• Handle connectors by the plug body, not the wires, to avoid damage
• Route and secure the harness to match original routing and strain reliefs