Parts for Frigidaire GCCG3048AB: Cook Top Parts

This replacement cooktop grate restores a stable, level surface for pots and pans on gas ranges. It helps maintain safe, consistent cooking by supporting cookware and protecting the cooktop surface from direct flame contact. What it does

• Supports cookware above the burner for even heat distribution and safe cooking
• Replaces cracked, chipped, or warped grates that cause wobbling or instability
• Protects the cooktop surface from spills and direct exposure to flames
• Works with sealed burner cooktops designed for this grate style

• One cooktop grate

• Allow the cooktop to cool completely before removing or installing the grate
• Lift old grate straight up to remove; set the new grate into place so it sits flat and stable
• Clean the surrounding cooktop area before installation; avoid abrasive cleaners on coated surfaces
• Handle porcelain-coated grates carefully to prevent chipping or scratching

Replacement snap-on cap that restores a finished appearance and helps protect underlying components from dirt and accidental contact. Fits original mounting locations to cover exposed hardware and improve appliance safety and aesthetics. What it does:

• Covers and protects exposed hardware, terminals or posts to reduce debris buildup and accidental contact.
• Restores a clean, finished look to panels, trim or appliance edges.
• Helps reduce rattling or vibration noise caused by missing trim pieces.
• Use when the original cap is cracked, broken, missing or when exposed fasteners are visible.

• Always disconnect power (and water, if applicable) before attempting any repair.
• Remove the damaged cap by hand or with a small pry tool; press the replacement cap onto the mounting post until fully seated.
• Avoid excessive force during removal/installation to prevent damage to the mounting post or surrounding trim.
• If mounting posts or clips are damaged, replace those components to ensure a secure fit.

This replacement cap covers and protects its designated opening or fastener on your appliance. It restores a clean, finished look and helps shield internal areas from dust and wear when the original cap is missing or damaged. What it does:

• Covers a specific opening, fastener, or trim end to protect the area
• Helps keep moisture, grease, and debris out of the assembly
• Restores proper fit and finished appearance
• Typical symptoms include a cracked, loose, discolored, or missing cap

• 1 cap

• Disconnect power and, if applicable, shut off gas/water before servicing
• Note the cap's orientation; gently unclip, pry, or unthread the original per model design
• Seat the new cap fully and avoid forcing or overtightening
• The cap is secure and does not interfere with moving parts

This replacement cap covers and protects a small opening or fastener on your appliance. It restores a clean, finished appearance and helps keep out dust and moisture when the original cap is missing or damaged. What it does:

• Covers a screw hole or open end as designed on the unit
• Helps block debris and moisture and can reduce rattles
• Maintains a clean, finished look and protects underlying hardware
• Replace if the original cap is cracked, loose, deformed, or missing

• 1 cap

• Disconnect power and allow any hot surfaces to cool before servicing
• Use a non-marring tool to gently remove the old cap to avoid scratching
• Align and press/snap the new cap into place; do not force
• If the cap conceals a fastener, the fastener is secure before reinstalling the cap

This genuine replacement cap restores a clean, finished look and helps protect the underlying fastener or opening on your appliance. Replace a missing or damaged cap to keep components covered and looking factory-fresh.

• Covers and protects an exposed screw, hinge, or opening from dust and debris
• Restores the appliance's finished appearance
• Helps maintain secure retention of the underlying component
• Common signs of failure: missing or broken cap, cap won't stay in place, cosmetic wear, visible exposed fastener/opening

• Disconnect power before servicing; if working near water or gas lines, shut those off as applicable
• Gently pry off the old cap; avoid scratching surrounding surfaces
• Align and press the new cap until it seats/snaps securely

Note: Quantity of two brackets

Replacement mounting screw used to secure panels and small components on compatible appliances. Restores proper fastening to reduce rattling and keep trim, control panels and brackets aligned for safe, quiet operation. What it does:

• Secures panels, trim, brackets and other small appliance components.
• Replaces loose, missing or damaged fasteners that can cause rattling, gaps or panel misalignment.
• Restores mechanical stability for control panels and interior trim pieces.

• Disconnect power to the appliance before servicing any panels or components.
• Use the correct screwdriver and start the screw by hand to avoid cross-threading.
• Tighten securely but do not overtighten; replace if threads are stripped or the screw will not secure the part.