Parts for Kitchenaid KGCC566HBL04: Cooktop, Burner And Grate Parts

Color: Biscuit. This grommett is located between the glasstop and the knobs. For black order W10854242. For white order WP3180081.

This grommet is located between the glasstop and the knobs. Color: White. Measures about 2 inches in diameter. For black order W10854242. For biscuit order 3191817.

The Grommet is an OEM part for Whirlpool cooktops. This part provides a secure fit and cushioning for the control knobs on the cooktop, ensuring smooth operation and preventing damage to the control panel.  

Causes of a bad knob grommet can include general wear and tear, exposure to high temperatures, or damage from frequent use.  

Symptoms of a bad knob grommet include:

• Loose or wobbly control knobs
• Difficulty in turning the knobs
• Knobs not staying in place or falling off
• Visible cracks or wear in the grommet

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Mouse grey. Location: Right front, left rear.

Color: Black. Location: Right rear. 12K.

Color: Black. Location: Left front. 14K.

Color: Mouse grey. Location: Left front. 14K.

Color: Mouse grey. Location: Right rear, center.

Color: Black. Size: Small.

Color: Biscuit. Size: Small.

Color: White. Other colors: For black use 4455573, for biscuit use 4455576.

Color: Biscuit. Other colors: For white use 4455575, for black use 4455573.

Color: Black. Other colors: For white use 4455575, for biscuit use 4455576.

Color: Mouse grey. Size: Large.

Color: Black. Size: Large.

Color: Biscuit. Size: Large.

Color: Mouse grey.

Color: Biscuit.

Color: Black.

Color: Mouse grey. Left side burner grate.

Color: Biscuit. Left side burner grate.

Color: Black. Left side burner grate.

Color: Biscuit.

Color: Mouse grey.

Color: Biscuit. Other colors: For black use 3191925, for white use WP3191923, for almond use 3191924.

Color: White. Other colors: For black use WP3191922, for biscuit use 3191925, for almond use 3191924.

The Burner Control Knob is an OEM part for Whirlpool ranges and cooktops. It is used to control the heat level of the burners, allowing for precise adjustments during cooking. This knob fits securely onto the burner valve stem, providing easy and reliable control over the gas or electric burners.

Over time, the burner control knob can become faulty. Causes of a bad burner control knob include regular wear and tear, exposure to high heat, or accidental impacts that cause the knob to crack or break. A damaged knob can make it difficult to adjust the burner settings accurately.

Symptoms of a bad burner control knob include:

• The knob not turning smoothly or feeling loose
• Difficulty in adjusting the burner flame or heat level
• The knob being cracked, broken, or missing
• The burner not responding to adjustments made with the knob

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This orifice holder secures the burner orifice and helps direct gas to the burner for proper ignition. It replaces a worn or damaged holder to restore steady burner flame and reliable lighting. What it does:

• Holds and positions the burner orifice so gas flows correctly to the burner
• Ensures consistent gas delivery for stable ignition and flame shape
• Commonly used when a burner has weak or uneven flame or fails to light reliably
• Works with the factory orifice and valve components to maintain correct operation

• Turn off the appliance power and shut off the gas supply before servicing
• Inspect the orifice and surrounding seals; replace any damaged parts to prevent leaks
• Seat the holder fully and reassemble per the manufacturer's diagram
• After installation, check all connections for leaks and verify proper burner ignition

This G4 orifice holder mounts beneath the cooktop to secure the burner orifice and route gas from the valve to the burner head. Replacing a damaged holder helps restore proper gas flow and consistent burner performance.

• Holds and aligns the orifice for the G4-designated surface burner
• Channels metered gas from the valve to the burner head
• Supports stable, even flame and reliable ignition at that burner
• A worn, cracked, or stripped holder may cause weak/uneven flame, delayed ignition, or a gas odor near the burner

• Disconnect power and shut off the gas supply before servicing; allow the appliance to cool
• Remove burner caps/heads and access the holder
• Transfer the existing orifice spud if reusing, or install the correct orifice specified for your gas type
• Tighten fittings to spec and leak-test all gas connections with an approved solution before restoring service

This orifice holder channels gas from the valve to the burner on your gas range or cooktop, aligning the orifice for a stable flame. Replace a damaged holder to restore reliable ignition and consistent burner performance.

• Routes gas from the valve to the burner through the orifice
• Positions and supports the burner base for proper flame pattern
• Maintains alignment of components for consistent ignition
• Typical symptoms: burner won't ignite, delayed ignition, weak or uneven flame, visible cracks or stripped threads on the holder

• Shut off gas supply and disconnect power before servicing
• Remove grates, caps, and burner head to access the holder
• Transfer the existing orifice spud and any seals to the new holder; ensure connections are snug and correctly aligned
• After reassembly, restore gas and check all connections for leaks per manufacturer instructions

Location: Left front. 14,000 BTU.

The Burner Head is an OEM replacement part for Whirlpool gas ranges. This is the smaller burner head and it distributes gas evenly through the ports to produce a focused and consistent flame for temperature control during cooking.

Size: Small

Due to spills, grease buildup, corrosion, or wear and tear, the small burner head can deteriorate, clogging its ports and affecting gas distribution. When this occurs, the burner head may struggle to maintain a steady flame, impacting cooking performance.

Symptoms of a faulty Small Burner Head include:

• Uneven or low flames on the small burner
• Difficulty igniting the burner
• Clogged ports or visible rust/corrosion

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: Large.

This factory replacement screw secures panels, brackets, and covers in your appliance. Replacing missing or stripped hardware restores a solid fit, reduces vibration and rattles, and keeps components properly aligned during everyday use. What it does:

• Fastens panels, trim, brackets, and internal components to the cabinet or chassis
• Helps maintain alignment and reduce vibration or rattling noises
• Replaces missing, rusted, or stripped screws discovered during service
• Matches the OEM spec for locations where this part is called out on your model's diagram

• Disconnect power (and gas or water, if applicable) before servicing
• Use the appropriate driver; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent stripping metal or plastic
• Replace hardware one screw at a time to keep parts aligned

The Torx Screw is an OEM replacement part for Whirlpool brand appliances. The Torx Screw is responsible for providing secure and stable connections between different components of washing machines, dryers, dishwashers, and more. These screws are characterized by their star-shaped drive design, which offers better torque transfer and reduces the risk of stripping or cam-out. Sold individually. 7-18 x 3/4"

Causes of a bad Torx screw can include stripping of the screw head, rust or corrosion from prolonged exposure to moisture, or damage from over-tightening or cross-threading. A compromised screw can lead to loose or insecure parts, which can affect the performance and safety of the appliance.

Symptoms of a bad Torx screw include:

• The screw head being stripped and difficult to turn
• Rust or corrosion visible on the screw
• The screw not holding components securely
• Loose or rattling parts within the appliance

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Color: Biscuit.

Color: Mouse grey.