Parts for Maytag MFT2772HEZ02: Dispenser Front Parts

This extra-large pad assembly cushions and stabilizes the washer tub to help reduce vibration and noise during operation. It's a direct-fit replacement when the original pad is worn, torn, or compressed. What it does:

• Provides cushioning between the tub and cabinet to absorb shock and reduce banging
• Helps minimize vibration and movement during spin cycles for smoother operation
• Prevents metal-to-metal contact that can cause noise or wear
• Maintains proper tub alignment to support reliable washing performance

• One extra-large pad assembly

• Disconnect power and water before starting any repair
• Access may require removing the washer cabinet or front panel; follow the OEM service manual
• Inspect mounting surfaces and replace any damaged fasteners or clips

This door ice separator assembly guides ice from the dispenser chute to the dispenser tray, helping prevent jams and misfeeds. It replaces a cracked, warped, or broken separator to restore smooth ice dispensing. What it does:

• Directs ice through the dispenser chute so cubes drop cleanly into cups or glasses
• Helps prevent ice clumping and jams at the door dispenser
• Restores proper alignment of the dispenser path after damage or wear
• Useful when ice falls unevenly or gets stuck in the dispenser area

• Basic removal of the dispenser inner door panel may be required; keep track of fasteners and clips.
• Disconnect power to the appliance before starting work to avoid electrical or mechanical hazards.
• Inspect surrounding chute and dispenser components for damage and clean any ice buildup before reassembly.
• Use gentle force when snapping the new separator into place to avoid breaking tabs—do not force misaligned parts.

This refrigerator ice guide channels cubes and crushed ice along the intended path so they land in your bin or glass. When the guide is damaged or missing, ice can scatter, jam, or miss the dispenser opening. What it does

• Guides ice from the ice maker/bucket into the bin and through the dispenser chute
• Helps keep ice flowing smoothly and reduces spills at the opening
• Restores proper aim for cubed and crushed ice
• Typical symptoms: ice spraying or missing the glass, frequent jams, or visible damage to the guide

• 1 ice guide

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and access the guide per your model's design
• Transfer and reuse existing mounting screws or clips, if applicable
• Verify alignment, then test both cubed and crushed dispensing

The Dispenser Drip Tray is an OEM part for Whirlpool refrigerators. It is a plastic tray located below the ice and water dispenser that catches any accidental spills or drips during use. 

Symptoms of a bad drip tray can include:

• Ice or water accumulation under the dispenser area  
• Overflow or leakage onto surrounding counter surfaces
• Stains or moisture damage below the refrigerator

Causes of drip tray issues occur from cracks, punctures, or breakage rendering it unable to hold liquid. Normal wear over extended use may also cause trays to develop leaks.

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, and Kenmore brands.

This dispenser light replaces the small lamp that illuminates the refrigerator's ice/water dispenser alcove. It restores clear visibility of the dispenser area in low light so you can see fill levels and selections while dispensing.

• Provides illumination for the dispenser alcove when the control turns the light on
• Common symptoms: no dispenser light, dim or flickering light, or intermittent illumination
• Helps with accurate filling and improves visibility when dispensing ice or water

• Unplug the refrigerator or disconnect power before servicing
• Access the dispenser housing; remove any trim or lens as needed to reach the light
• Release locking tabs or screws and unplug the wire connector from the old light
• Connect and seat the new light, reassemble, restore power, and test operation

This ice door motor drives the dispenser flap that opens for ice dispensing and closes to seal the chute. Replacing a weak or failed motor restores smooth door movement and helps prevent warm air and moisture from entering the freezer. What it does:

• Actuates the ice chute door during dispensing and returns it closed for a proper seal
• Helps reduce frost, condensation, and ice clumping around the dispenser
• Can address ice not dispensing due to the door not opening/closing
• May resolve clicking or grinding noises from the dispenser area

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove dispenser trim/control panel to access the ice door assembly; handle wiring carefully
• Note linkage and wire orientation before removal to ensure proper reassembly
• After installation, test the dispenser to verify the door opens/closes and seals the chute