Parts for Maytag MSS26C6MFB00: 09 - Dispenser Parts

This drip tray catches and guides condensate or minor leaks away from the appliance base to help protect flooring and cabinetry. It fits beneath the appliance where small amounts of water typically collect. What it does:

• Collects and contains dripping or condensed water to prevent puddling under the appliance
• Channels moisture to a safe area to reduce risk of water damage to floors or surrounding cabinetry
• Helps identify leaks by localizing where water accumulates
• Useful for appliances that produce condensate or occasional drips during normal operation

• One drip tray

• Disconnect power to the appliance before moving or servicing it
• Slide the tray into place under the appliance base; ensure it sits flat and is centered
• Inspect tray for cracks or obstructions before reinstalling; replace if damaged

This drip tray catches and guides condensate or minor leaks away from the appliance base to help protect flooring and cabinetry. It fits beneath the appliance where small amounts of water typically collect. What it does:

• Collects and contains dripping or condensed water to prevent puddling under the appliance
• Channels moisture to a safe area to reduce risk of water damage to floors or surrounding cabinetry
• Helps identify leaks by localizing where water accumulates
• Useful for appliances that produce condensate or occasional drips during normal operation

• One drip tray

• Disconnect power to the appliance before moving or servicing it
• Slide the tray into place under the appliance base; ensure it sits flat and is centered
• Inspect tray for cracks or obstructions before reinstalling; replace if damaged

This dispenser light replaces the small lamp that illuminates the refrigerator's ice/water dispenser alcove. It restores clear visibility of the dispenser area in low light so you can see fill levels and selections while dispensing.

• Provides illumination for the dispenser alcove when the control turns the light on
• Common symptoms: no dispenser light, dim or flickering light, or intermittent illumination
• Helps with accurate filling and improves visibility when dispensing ice or water

• Unplug the refrigerator or disconnect power before servicing
• Access the dispenser housing; remove any trim or lens as needed to reach the light
• Release locking tabs or screws and unplug the wire connector from the old light
• Connect and seat the new light, reassemble, restore power, and test operation

This refrigerator ice guide channels cubes and crushed ice along the intended path so they land in your bin or glass. When the guide is damaged or missing, ice can scatter, jam, or miss the dispenser opening. What it does

• Guides ice from the ice maker/bucket into the bin and through the dispenser chute
• Helps keep ice flowing smoothly and reduces spills at the opening
• Restores proper aim for cubed and crushed ice
• Typical symptoms: ice spraying or missing the glass, frequent jams, or visible damage to the guide

• 1 ice guide

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and access the guide per your model's design
• Transfer and reuse existing mounting screws or clips, if applicable
• Verify alignment, then test both cubed and crushed dispensing

This spigot directs water from the refrigerator's water/ice system to the dispenser or ice maker, restoring proper flow and containment. Replace a cracked or worn spigot to stop leaks and poor dispensing. What it does:

• Channels water from the internal water line to the dispenser or ice/ice-maker area
• Prevents leaks and directs flow into the dispenser or ice chute
• Can stop drips, spraying, or pooling caused by a damaged spigot
• Works as a simple replacement when the original is cracked, warped, or blocked

• One replacement spigot

• Disconnect power and shut off the refrigerator water supply before starting
• Remove access panels or bin(s) as needed to reach and remove the old spigot
• Inspect seals and gaskets; replace if damaged to ensure a watertight fit
• After installation, restore water and power, then check carefully for leaks

The Dispenser Pad is an OEM part for Whirlpool refrigerator dispensers. It attaches under the dispenser lever to activate water and ice functions with light finger pressure. 

Symptoms of a bad dispenser pad include:

• Unable to dispense water or ice by pressing the lever
• Leaks or water drips around the dispenser area  
• The dispenser mechanism making noises when engaged

Causes of a bad dispenser pad can be wear over time, tears in the rubber material, or failure of the electrical contacts on the pad. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dispenser Pad is an OEM part for Whirlpool refrigerator dispensers. It attaches under the dispenser lever to activate water and ice functions with light finger pressure. 

Symptoms of a bad dispenser pad include:

• Unable to dispense water or ice by pressing the lever
• Leaks or water drips around the dispenser area  
• The dispenser mechanism making noises when engaged

Causes of a bad dispenser pad can be wear over time, tears in the rubber material, or failure of the electrical contacts on the pad. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement cabinet screw secures panels, brackets, and ducts in Whirlpool-built appliances so components stay aligned and secure. Replacing missing or stripped hardware helps reduce vibration, rattling, and gaps that can affect performance.

• Fastens panels, brackets, and internal components in the appliance cabinet
• Helps maintain proper alignment and reduce vibration or rattling noises
• Restores a tight fit where original hardware is missing, damaged, or stripped
• Typical symptoms: loose paneling, buzzing/rattling sounds, or parts that won't stay fastened

• Disconnect power; for gas models, also shut off the gas supply
• Replace one fastener at a time to preserve alignment and match to the original hardware
• Use the correct driver; start threads by hand to avoid cross-threading
• Do not overtighten into sheet metal