Parts for Frigidaire FPHT2097VF3: Door Parts

The Nameplate is an OEM for Frigidaire appliances. It affixes to the exterior and clearly identifies the brand.

Causes of a damaged nameplate can include normal wear and tear over time outdoors, exposure to cleaning chemicals that breakdown adhesive integrity or accidental damage from impact.

Symptoms of a bad nameplate include:

• Nameplate lifted, peeling or completely removed from surface
• Faded or worn lettering obscuring model identification
• Dirty, stained appearance detracting from product aesthetics

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Fresh Food Door Gasket (Gray) is an OEM replacement part for Frigidaire refrigerators. As a critical component, this gasket forms an insulating seal around the refrigerator's fresh food door opening. It helps maintain interior temperatures and energy efficiency. 

Causes of a bad gasket can include cracks or splits developing from repeated opening and closing of the door. General wear through daily use may also cause seal degradation over time. 

Symptoms of a bad door gasket include: 

• Higher than normal energy bills   
• Excess frost or moisture buildup inside  
• Difficulty closing the refrigerator door fully
• Inability to reach optimal cooling levels

This OEM Frigidaire replacement is compatible with some Electrolux, Kelvinator, and Kenmore refrigerators as well.

This replacement gasket restores a tight, flexible seal where your appliance needs it—helping contain air, moisture, or heat so performance stays consistent and leaks are minimized. Use it to replace a worn or damaged seal and improve efficiency.

• Forms a compressible seal between two mating surfaces
• Helps prevent air or water from escaping, supporting correct temperature and moisture control
• Replace if the old gasket is torn, cracked, hardened, misshapen, or won't stay seated
• Common symptoms include visible gaps, poor closure/fit, moisture at the edge, or temperature inconsistencies near the opening

• Disconnect power; turn off water supply if applicable
• Remove the old gasket and thoroughly clean the channel/mating surfaces before installing
• For door-style seals, warming the gasket (warm water or low heat) can help it relax; set corners first and seat evenly
• After installation, check for leaks or air gaps during a test run

A replacement refrigerator bin that stores and organizes food items to help keep shelves tidy and accessible. Fits into compatible shelf tracks and restores usable storage space in the fresh-food compartment. What it does:

• Holds fruits, vegetables, deli items, or other refrigerated goods for easy access and organization
• Slides or rests on shelf tracks to form a secure storage receptacle
• Replaces cracked, chipped, or discolored bins that no longer seal or support contents
• Helps prevent small items from rolling or tipping on the shelf

• One replacement refrigerator bin

• Remove all food and shelves near the install area before replacing the bin
• Slide or set the bin into the shelf tracks until it seats securely (no tools typically required)
• Inspect surrounding tracks and supports for damage; replace if worn to ensure proper fit
• Clean the bin with mild detergent and warm water; avoid abrasive cleaners

This clear replacement crisper drawer stores fruits and vegetables and restores organized storage in the refrigerator. It fits into existing tracks and provides a sealed, easy-access compartment for fresh produce. What it does:

• Replaces a cracked, chipped, or broken crisper/drawer to restore storage capacity
• Keeps produce separated from main shelves to help prevent bruising and cross-contamination
• Slides into existing tracks for smooth in-and-out access
• Prevents items from falling onto lower shelves when drawer is closed

• Disconnect power only if working inside the refrigerator to avoid accidental contact with components
• Empty the drawer and remove any shelves or stops blocking removal before pulling the old bin out
• Align the bin with the tracks and slide it in until it seats; verify smooth operation
• If the bin does not seat easily, check for obstructions or damaged tracks before forcing

Replacement refrigerator bin that restores storage space and keeps foods contained and visible. Clear plastic construction helps you organize produce and deli items while preventing spills and shifting during normal use. What it does:

• Replaces a cracked, broken or missing refrigerator drawer so food stays contained and off shelving
• Slides into the refrigerator's bin rails to create an organized storage area for produce, deli items or packaged goods
• Clear design makes it easy to see contents without removing the bin
• Helps prevent spills from spreading when a shelf is bumped or an item tips

• Typically installs by sliding into the existing bin rails; no tools required for most models
• Inspect rails and mounting tabs for damage before installing; damaged rails may need replacement
• Clean with mild detergent and warm water; avoid abrasive pads and harsh chemicals

This bearing supports and allows smooth rotation of the dryer drum, helping reduce noise and wear. Replacing a worn bearing restores stable drum movement and helps prevent scraping, thumping, or drag during cycles.

• Supports the rear of the drum for proper alignment and smooth rotation
• Can help address squeaking, grinding, scraping, or thumping sounds
• Reduce drum wobble, drag, or intermittent stopping during operation
• Wear item that can degrade over time with heat and load stress

• Disconnect power before service and allow components to cool
• Access typically requires removing the top and front panels
• Inspect the drum shaft, support bracket, and glides for wear; replace if needed
• Apply manufacturer-approved high-temp lubricant where specified

The Hook is an OEM part for Frigidaire refrigerators. It helps to ensure a secure and proper closure of the refrigerator door.

A bad door closer hook can be caused by wear and tear, damage, or misalignment. Signs of a faulty door closer hook include the door not closing fully or not staying closed, difficulty in opening or closing the door smoothly, or a loose or wobbly door.

Symptoms of a bad door closer hook can include:

• The refrigerator door not sealing properly
• Excessive force required to open or close the door
• Visible damage or misalignment of the door closer hook

Replace your worn or damaged door closer hook with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic

Replacement door magnet that helps the refrigerator or freezer door stay closed for a tighter seal and more consistent cooling. Restores magnetic hold so doors close reliably and reduce warm spots. What it does

• Provides magnetic hold for the door liner so the door stays shut during normal use
• Helps maintain the gasket engagement to preserve internal temperature
• Common symptom: door not staying closed, food warming, or frost build-up near the door
• Used in door/gasket assembly where magnets secure the seal

• Turn off power to the appliance or unplug before removing door trim or accessing internal components
• Remove door liner or gasket per service instructions to access and replace the magnet; keep fasteners and seals intact
• Press or seat magnet into its channel or mounting location; use the OEM fastener or adhesive method specified by the manufacturer

This door handle assembly provides a ready-to-install replacement to restore a secure, easy-grip opening for your refrigerator door. Durable construction replaces a worn or broken handle for reliable daily use. What it does:

• Replaces a cracked, loose, or broken refrigerator door handle to restore safe operation and appearance
• Provides a solid grip for opening and closing the door smoothly
• Matches factory mounting points for proper fit and alignment
• Helps prevent door damage and keeps the seal functioning by ensuring correct door movement

• Disconnect power to the appliance before beginning any repair to avoid injury
• Remove any trim or access panels as needed to access mounting screws; retain fasteners for reassembly
• Hand-tighten screws, then snug—do not overtighten to avoid cracking the handle or trim

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a service wrench used to loosen and tighten appliance fasteners for maintenance and repairs, making access and part replacement easier for technicians and DIYers. Durable tool designed for specific appliance fastener sizes. What it does:

• Provides the correct fit and leverage for removing or installing designated appliance nuts, bolts, and fittings
• Helps safely access internal components during service and part replacement
• Reduces risk of rounding fasteners compared with improvised tools
• Useful for routine maintenance tasks and repair procedures that require a dedicated wrench

• One wrench

• Use the wrench only for its intended appliance fasteners; avoid excessive force
• Disconnect power and water to the appliance before beginning service
• Wear safety gloves and eye protection when working on appliances