Parts for Frigidaire FRU1767GW2: 03 - Door Parts

The Door Gasket is an OEM part for Frigidaire refrigerators. It ensures a tight seal around the door, preventing cold air from escaping and maintaining the set temperature inside the appliance. Over time, the gasket can wear out, become brittle, or lose its elasticity, leading to gaps between the gasket and the appliance frame. The gasket measures approximately 31" x 60"

Causes of a bad door gasket can vary from normal wear and tear to accidental damage. 

Symptoms of a bad Gasket include:

• Noticeable gaps or tears in the gasket
• Difficulty in maintaining the set temperature
• Condensation or frost buildup around the door

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Dairy Door is an OEM replacement part for Frigidaire side-by-side refrigerators. As the access point to the dedicated dairy compartment, the door is designed with precision seals to maintain optimal humidity levels inside. This helps keep dairy and other perishable items fresh longer.

Causes of a bad dairy door can include worn or damaged seals, dents or impacts warping the door frame, or issues with the electronic components that control humidity levels.

Symptoms of a bad dairy door include: 

• Excessive frost or ice buildup inside the dairy compartment   
• Difficulty opening and closing the door smoothly  
• Warm or dried-out dairy products despite a cold refrigerator interior
• Moisture leaks around the door seals  

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore side-by-side models.

This replacement inner door panel restores the interior surface of the door. It supports door bins/shelves and provides a stable surface for the door gasket to seal, helping keep cold air in and items secure.

• Forms the interior face of the door and supports door bins/shelves
• Provides the gasket with a flat surface to help maintain a proper seal
• Replace if cracked, warped, or separating from the door frame
• Common symptoms include loose/falling door bins, visible damage, or air leaks/frost near the door

• Disconnect power and empty items from the door before service
• Remove the door per the appliance manual and lay it flat to prevent twisting
• Transfer the door gasket and any reusable hardware from the old panel if applicable
• Install the new panel and tighten fasteners evenly; verify the gasket seals all around

This is a replacement name plate — the exterior label that displays model, serial and rating information and restores the factory identification on your appliance. Keeps appliance identification readable and helps with service or resale. What it does:

• Replaces a torn, faded or missing name plate so model and serial info are visible
• Restores factory-applied rating and regulatory information printed on the appliance
• Helps identify the correct parts and service requirements
• Prevents confusion from illegible or damaged labels during inspections or resale

• Always disconnect power (and water, if applicable) before starting work.
• Remove the old plate and any adhesive residue; clean and dry the mounting surface before installing.
• Many name plates attach with adhesive or small fasteners—align carefully and press firmly.
• Handle the printed side gently to avoid smudging; keep it fully legible.

The Door Handle is an OEM part for Frigidaire refrigerators. This part allows for easy opening and closing of the door, ensuring convenient access to your frozen foods. 

Over time, door handles can become loose, cracked, or completely break off due to frequent use, accidental impacts, or material fatigue. This can make opening the freezer more difficult and may even lead to further damage to the door or the sealing mechanism if users apply excessive force when trying to open or close the door.

Symptoms of a bad Door Handle include:

• The handle is loose or wobbly
• Visible cracks or breaks in the handle
• Difficulty in opening the door due to a damaged or missing handle 

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This bearing installs in the refrigerator/freezer door hinge to provide a smooth pivot point and maintain alignment. Replacing a worn bearing restores easy door movement and helps the door close and seal correctly.

• Provides a low-friction surface between the hinge pin and hinge bracket for smooth door pivoting
• Helps maintain proper door height and alignment for a reliable gasket seal
• Typical symptoms of wear: squeaking or grinding when opening, door binding or dropping, door not closing fully or popping open
• Excess wear can contribute to air leaks and frost buildup around the door

• Disconnect power before servicing; remove or secure items in the door
• Support the door; remove hinge fasteners and lift the door off if required
• Note and retain any shims/spacers; install the new bearing in the hinge as oriented in the diagram
• Reinstall and align the door; verify smooth operation and a complete gasket seal. Do not lubricate unless specified by the manufacturer

This door gasket creates an airtight seal around your refrigerator or freezer door or lid, keeping cold air in and moisture out. Replace a worn gasket to restore temperature control, reduce frost, and support efficient operation.

• Forms a tight perimeter seal between the cabinet and door/lid to prevent air leaks
• Helps maintain stable internal temperatures and consistent cooling performance
• Reduces frost and condensation caused by a failed or leaking seal
• Common symptoms: visible tears or cracks, gaps, warping/shrinkage, door not sealing or staying closed

• Disconnect power; remove items from the door/lid as needed
• Warm the new gasket (soak in warm water or gently heat) to make it pliable, then straighten corners
• Fit the gasket into the channel or under the retainer, working evenly around the perimeter
• Check closure all around with a paper test; adjust hinges/leveling as needed and allow the gasket to relax and conform

Quantity of 1 clip.

Note: See kit# 5303922007 and 5304406520.

Color: Chrome

The Refrigerator Door Shelf is an OEM replacement part for Frigidaire refrigerators, designed to offer convenient storage space for jars, bottles, and other condiments within easy reach. Measures approximately 24 1/2 inches wide X 2 1/2 inches deep

Causes of a bad Refrigerator Door Shelf can include physical damage such as cracks or breaks from overloading it with too heavy items. Additionally, wear and tear over time can lead to the shelf becoming damaged.  

Symptoms of a bad Refrigerator Door Shelf include:

• Visible cracks or damage
• The shelf sagging or unable to retain items  
• Difficulty fitting the shelf into its designated slots  

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Door Bin is an OEM replacement part for Frigidaire refrigerators. It provides interior storage by hanging securely inside the refrigerator door. The bin measures approximately 13 inches wide at its longest point, 5 inches deep, and 4 inches tall.

Causes of a bad door bin can include damage from overloading or improper handling. The plastic material can become cracked or warped from stress over time.

Symptoms of a failed door bin include:

• Items no longer staying in place and spilling out
• The bin hanging loose inside the door
• Cracked or broken plastic shelves

This part is also compatible with some Electrolux, Kelvinator, and Kenmore side-by-side refrigerator models.

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

The Refrigerator Door Gasket Clips are OEM parts for Frigidaire refrigerators. These clips secure the door gasket in place, ensuring a tight seal to maintain the internal temperature and prevent cold air from escaping. This pack contains 40 clips, which secure the interior trim pieces and hold the gasket and liner to the freezer lid.

Over time, the gasket clips can become damaged or worn out due to frequent opening and closing of the refrigerator door, exposure to moisture, or accidental impacts. If the clips fail, the door gasket may not stay in place, compromising the refrigerator's efficiency.

Symptoms of bad refrigerator door gasket clips include:

• The door gasket not staying securely in place
• Visible damage or wear on the clips
• Cold air escaping from around the door
• Increased energy consumption due to poor sealing

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.