Parts for Frigidaire GFU14M3AW7: 02 - Door Parts

The Upright Freezer Door Gasket is an OEM part for Frigidaire upright freezers. This gasket ensures a tight seal around the freezer door, preventing warm air from entering and cold air from escaping, thus maintaining the optimal freezing temperature.

Causes of a bad freezer door gasket can include wear and tear over time, exposure to harsh cleaning chemicals that can degrade the material, or physical damage from frequent use or mishandling.

Symptoms of a bad freezer door gasket include:

• Noticeable gaps or cracks in the gasket
• Frost buildup inside the freezer
• Increased energy consumption
• The freezer door not closing properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

By Frigidaire. Includes Freezer key 5303310289.

The Freezer Door Key is an OEM replacement part for Frigidaire refrigerators. This small but essential component is designed to securely lock the freezer door, preventing accidental openings or unauthorized access.

Symptoms of needing to replace the freezer door key include:

• Difficulty in locking or unlocking the freezer door
• The key not fitting properly or becoming stuck in the lock
• Visible wear, damage, or breakage of the key itself

Causes of a faulty freezer door key can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the locking mechanism itself.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

This inner panel is a factory-style replacement trim piece that restores the interior finish and protective surface of the appliance door. It matches the original white finish for a consistent, clean appearance. What it does:

• Replaces a cracked, scratched or discolored inner door panel to restore appearance
• Protects internal door components from spills and everyday wear
• Helps maintain a proper seal and door alignment by restoring original fit
• Designed to match OEM fit and mounting points for a straightforward swap

• Remove power to the appliance before starting any repair
• Typical install requires removing the door outer panel and disconnecting lightweight clips or fasteners
• Handle part carefully to avoid cosmetic damage; use appropriate tools and a second set of hands for larger doors

This nameplate bezel is the exterior trim that surrounds and secures the appliance's front nameplate and control-panel area, restoring a finished appearance and protecting the panel edges from damage. What it does:

• Covers and protects the control-panel/nameplate edge from chips and wear
• Keeps the nameplate aligned and visually flush with the console
• Helps maintain a finished look after panel or nameplate replacement
• Reduces dirt and moisture intrusion at the panel seam

• Disconnect power to the appliance before starting any repair
• Usually installs with screws or snap clips; a screwdriver or trim tool may be needed
• Handle carefully to avoid scratching the finish during installation
• Follow OEM service instructions for proper fit and torque

Quantity of 1 clip.

Note: See kit# 5303922007 and 5304406520.

This right-side end cap replaces a worn or broken trim piece to restore a clean fit and finish on the appliance. It secures the outer edge of the assembly and helps keep adjacent components aligned. What it does:

• Covers and protects the outer edge of the assembly to prevent gaps and sharp edges
• Secures trim and helps keep shelves or panels aligned and stable
• Restores appearance when the original cap is cracked, chipped, or missing
• Reduces rattling or movement caused by a loose or damaged end cap

• Installation is typically straightforward; part snaps or screws into place
• Use basic hand tools; keep track of any fasteners for reinstallation
• Inspect mating surfaces for damage and clean before fitting to ensure a secure fit
• If work requires panel removal near electrical or sealed-system components, disconnect power and follow safety instructions in the service manual

This left end cap secures the end of a dishwasher rack door assembly, helping keep the rack stable and rollers aligned for smooth operation. It replaces a worn or broken cap to restore proper rack function and fit. What it does

• Covers and protects the outer end of the rack door, preventing exposed edges.
• Holds rollers or hinges in place so the rack slides smoothly.
• Helps keep the rack aligned to prevent catching or uneven movement.
• Common symptom: cracked, missing, or loose end cap causing rack wobble or noisy operation.

• Always disconnect power to the appliance before beginning repairs.
• Usually installs by snapping into place or fastening with the original screws; use basic hand tools.
• Inspect adjacent rollers and mounting hardware while replacing the cap.
• If fit feels tight, avoid forcing parts—verify orientation before final installation.

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener