Parts for Kenmore 795.70329312 (79570329312, 795 70329312): Door Parts

The Handle Mounting Stud is an OEM replacement part for LG refrigerator doors. It provides a sturdy mounting point for the door handle assembly. Reliable handle connection and support is crucial for dependable door function and access. 

Causes of a faulty stud can include damage from excess weight or impact over time rendering the stud loose or unstable.

Symptoms of a bad stud include:

• Loose or sagging door handle  
• Difficulty opening and closing the refrigerator door  
• Potential for the handle to detach completely
• Safety concerns if the handle connection fails

This OEM LG replacement stud is also compatible with Sears/Kenmore models. 

The Door Gasket Assembly is an OEM replacement part for LG refrigerators. As a sealing system, it surrounds the door perimeter maintaining a thermal barrier. Proper alignment and fit preserves energy efficiency.

Causes of failure involve cracks developing from repeated compression. Mineral deposits accumulated over extended use may also harden material, diminishing its sealing ability.

Symptoms of a problematic gasket may include:

• Cooler air escaping around door edges
• Moisture accumulating on gasket surfaces
• Inner door temperatures fluctuating noticeably

This is an LG OEM part that is also compatible with some Kenmore models.

This door gasket assembly restores the door seal so the appliance holds a tight, reliable seal during use. Replacing a damaged gasket helps stop leaks and maintain consistent temperatures for proper operation. What it does:

• Forms the seal between the door and cabinet to prevent water/vapor or air loss
• Stops common symptoms such as visible leaks, moisture around the door, or poor temperature retention
• Replaces torn, stretched, or hardened gaskets that no longer seat properly
• Helps the appliance run more efficiently by restoring the intended seal

• Disconnect power (and water if applicable) before starting any repair
• Inspect the door and mounting channel for damage or debris; clean surfaces before installing the new gasket
• Seat the gasket evenly around the full door perimeter and secure any retaining clips or screws per OEM guidance

This refrigerator door gasket restores a tight seal around the door perimeter. Replacing a worn seal helps keep cold air in, block warm, humid air out, and maintain proper temperatures and efficiency.

• Creates the compression seal between the door and cabinet when closed
• Helps reduce frost, condensation, and temperature swings
• Replaces gaskets that are torn, cracked, warped, or no longer sealing
• Common symptoms: visible gaps, doors not closing fully, moisture around the door, or longer run times

• Disconnect power before servicing
• Warm the gasket in hot water or with a hair dryer on low to relax folds; do not overheat
• Start at the corners and press the gasket lip into the door liner groove, then work along the sides
• Close the door and check for uniform contact around the perimeter; level/adjust hinges if needed

The Mullion Flipper Assembly is an OEM part for LG refrigerators. This assembly, located between the refrigerator doors, helps seal the space between the doors when they are closed, improving energy efficiency by preventing cold air from escaping.

Causes of a bad mullion flipper assembly can include wear and tear over time, damage from frequent opening and closing of the doors, or issues with the hinges and connectors that secure it in place. A damaged or malfunctioning mullion flipper can lead to temperature inconsistencies and increased energy usage.

Symptoms of a bad mullion flipper assembly include:

• Visible damage or wear on the assembly
• Cold air escaping from between the refrigerator doors
• Increased frost buildup inside the refrigerator
• Higher energy bills due to the appliance working harder to maintain temperature

This OEM LG part is also compatible with Sears/Kenmore models.

The Door Basket is an OEM part for LG refrigerators. It is designed to provide convenient storage space directly on the refrigerator door. This basket offers an accessible solution for smaller items like condiments, eggs, or other perishables.

Causes of a bad door basket include normal wear and tear, as well as accidental impact or damage.

Symptoms of a bad door basket include:

• The basket no longer securely attaching to the refrigerator door
• Sections of the basket cracking or breaking off over time
• Loosening or inability to stay firmly in place on the door

This OEM LG part is also compatible with some Kenmore models.

This replacement door basket is the removable shelf that mounts to the inside of a refrigerator door to hold bottles, condiments and small food items. Restores secure storage and organization on the door. What it does:

• Provides a stable shelf on the refrigerator door for bottles, jars and small containers
• Replaces a cracked, broken or missing door bin that can no longer hold items safely
• Helps maintain organized door storage and prevents items from shifting during use
• Matches original fit where designed for this exact OEM part number

• One (1) door basket

• Typically installs by sliding or snapping into the factory door mounting slots; no special tools usually required
• Remove all items from the door and support the basket while detaching the old one to avoid dropping
• Inspect mounting tabs on the door for damage and replace if worn or broken

This door basket mounts on the inside of the refrigerator door to hold bottles, jars, and condiments. Replacing a cracked or missing bin restores secure, organized storage and helps prevent items from tipping or falling when the door opens.

• Provides shelf-style storage on the refrigerator door for jars, bottles, and small items
• Attaches to the molded door slots; keeps contents secure and accessible
• Replace if the bin is cracked, chipped, warped, or has broken locking tabs
• Common symptoms: bin falls off, won't stay seated, feels loose, or is missing

• Disconnect power before servicing for safety
• Lift the old bin straight up and off the door mounts
• Align the new basket with the slots and press down until fully seated
• Verify it's secure before loading with items

This refrigerator door shelf bin replaces a broken or missing bin on the door, restoring secure storage for bottles, jars, and condiments. It helps keep items organized and reduces spills when opening and closing the door.

• Attaches to the inner door rails to create usable storage on the door
• Replaces cracked, warped, loose, or missing bins
• Helps prevent items from tipping or falling during door movement
• Common signs: broken mounting tabs, visible cracks, bin won't stay seated

• Remove items from the existing bin; lift up to release it from the door rails
• Align the new bin with the door mounts and press down firmly until fully seated
• Confirm correct position on the door before loading items
• Handle plastic carefully; allow the part to reach room temperature before installation if delivered cold

This door basket assembly mounts to the refrigerator door to provide secure, convenient storage for bottles, jars, and condiments. Replacing a cracked or loose bin restores usable door storage and helps prevent spills when opening and closing.

• Creates additional door-mounted shelf space for beverages and condiments
• Direct replacement for a damaged, warped, or missing door bin
• Helps keep items organized and reduces tipping during door movement
• Seats on the molded door-liner hooks/tabs when properly aligned

• Remove all items from the existing bin; lift the bin straight up and out of the door-liner slots
• Align the hooks/tabs of the new bin with the intended position and lower until fully seated
• Do not force into place; verify correct location and ensure the bin is securely engaged before loading
• Avoid overloading to prevent stress or cracking

This door basket assembly mounts to the refrigerator door to provide secure, convenient storage for bottles, jars, and condiments. Replacing a cracked or loose bin restores usable door storage and helps prevent spills when opening and closing.

• Creates additional door-mounted shelf space for beverages and condiments
• Direct replacement for a damaged, warped, or missing door bin
• Helps keep items organized and reduces tipping during door movement
• Seats on the molded door-liner hooks/tabs when properly aligned

• Remove all items from the existing bin; lift the bin straight up and out of the door-liner slots
• Align the hooks/tabs of the new bin with the intended position and lower until fully seated
• Do not force into place; verify correct location and ensure the bin is securely engaged before loading
• Avoid overloading to prevent stress or cracking

This door basket assembly mounts to the refrigerator door to provide secure, convenient storage for bottles, jars, and condiments. Replacing a cracked or loose bin restores usable door storage and helps prevent spills when opening and closing.

• Creates additional door-mounted shelf space for beverages and condiments
• Direct replacement for a damaged, warped, or missing door bin
• Helps keep items organized and reduces tipping during door movement
• Seats on the molded door-liner hooks/tabs when properly aligned

• Remove all items from the existing bin; lift the bin straight up and out of the door-liner slots
• Align the hooks/tabs of the new bin with the intended position and lower until fully seated
• Do not force into place; verify correct location and ensure the bin is securely engaged before loading
• Avoid overloading to prevent stress or cracking

This stopper assembly cushions and limits the door travel to prevent slamming and ensure correct door alignment. It restores smooth, controlled closing and helps reduce noise and wear on the door hinge area. What it does:

• Absorbs door impact to prevent hard slams and reduce noise
• Keeps the door from overtravel for consistent alignment
• Helps protect hinge and cabinet edges from damage
• Restores proper door closing feel when worn or broken

• One stopper assembly as shown

• Disconnect power and empty door area before starting repairs
• Access may require removing door trim or inner panel
• Use basic hand tools; avoid forcing the part into place to prevent damage

This hinge cam fits the door hinge and provides the lift/settle action that helps the door open and close smoothly. Replacing a worn cam can reduce clicking and restore consistent door movement and alignment.

• Provides cam action at the hinge for smooth door travel
• Helps the door seat closed and maintain alignment
• Common symptoms include clicking/knocking at the hinge, rough or uneven door movement, or slight door sag
• Visual wear such as flat spots or grooves on the cam is a typical failure sign

• Disconnect power to the appliance before servicing
• Support the door to prevent injury; remove hinge cover and hardware as needed
• Note the cam's orientation and any washers/spacers and transfer them to the new part
• After installation, verify door operation and gasket alignment; adjust hinge if needed

The Lower Refrigerator Door Hinge is an OEM part for LG refrigerators. This hinge supports the refrigerator door, allowing it to open and close smoothly while maintaining proper alignment. It is designed to handle the weight of the door and ensure a secure and stable operation over time.

Causes of a bad lower refrigerator door hinge can include regular wear and tear, physical damage from overloading or impacts, and gradual loosening over time. A faulty hinge can lead to misalignment, difficulty in opening or closing the door, and potential damage to the door seal.

Symptoms of a bad lower refrigerator door hinge include:

• The door not closing properly or staying open
• Sagging or misaligned door
• Unusual noises when opening or closing the door
• Gaps in the door seal, causing cooling inefficiency

This OEM LG part is also compatible with Sears/Kenmore models.

The Door closer is an OEM part for LG refrigerators, this part prevents the refrigerator door from swinging open too widely. By limiting the door's range of motion, the Door Stop ensures that the door opens smoothly and safely, contributing to the longevity of the appliance and maintaining the aesthetic integrity of your kitchen space.

Causes of a bad Door closer can stem from physical damage, wear and tear over time, or loosening of the component due to repeated use. 

Symptoms of a bad Door closer include:

• The refrigerator door swinging open too far
• Damage or marks on adjacent walls or furniture from the door hitting them
• Increased wear on the refrigerator's hinges due to uncontrolled door movement

This OEM LG part is also compatible with some Kenmore models.

This cover assembly protects and secures an electrical connector, helping keep wiring aligned and shielded from moisture and debris. It restores a clean, stable connection to support reliable appliance electrical function. What it does:

• Shields an electrical connector from dirt, moisture and rubbing that can damage wires.
• Holds the connector in place to prevent loose or intermittent electrical connections.
• Helps reduce arcing and shorting risk by keeping contacts covered and aligned.
• Resolves symptoms such as intermittent power, component failure, or non-responsive controls when caused by a damaged or missing connector cover.

• One cover assembly (connector) as shown.

• Disconnect power to the appliance before inspecting or replacing electrical parts.
• Handle wiring and the connector gently to avoid bending contacts or breaking clips.
• Installation typically requires only basic tools; fit before final reassembly.
• If corrosion or wire damage is present, repair or replace affected wiring/connectors per OEM guidance.

This connector assembly secures and drives the freezer drawer bar so the drawer opens and closes smoothly. Replaces a worn or broken bar/gear assembly to restore proper drawer movement and alignment. What it does:

• Transfers drawer motion to the slide mechanism so the freezer drawer glides correctly
• Replaces worn or stripped gears that cause slipping, grinding, or uneven movement
• Secures the drawer bar to the internal slide/track to prevent misalignment or sagging
• Useful when a drawer won't open/close smoothly, catches, or rattles during operation

• Disconnect power before servicing and remove stored items from the drawer
• Generally replaces with basic hand tools; support the drawer while detaching and installing the assembly
• Inspect surrounding slide components for wear and replace if needed for reliable operation

This connector assembly secures and drives the freezer drawer bar so the drawer opens and closes smoothly. Replaces a worn or broken bar/gear assembly to restore proper drawer movement and alignment. What it does:

• Transfers drawer motion to the slide mechanism so the freezer drawer glides correctly
• Replaces worn or stripped gears that cause slipping, grinding, or uneven movement
• Secures the drawer bar to the internal slide/track to prevent misalignment or sagging
• Useful when a drawer won't open/close smoothly, catches, or rattles during operation

• Disconnect power before servicing and remove stored items from the drawer
• Generally replaces with basic hand tools; support the drawer while detaching and installing the assembly
• Inspect surrounding slide components for wear and replace if needed for reliable operation

This cover assembly protects and secures the control connector area to prevent damage and ensure reliable electrical connections. It restores the original housing around the connector for safe operation and proper fit. What it does

• Covers and protects the appliance's connector area from dirt, moisture, and accidental contact
• Helps keep wiring and plug ends correctly positioned to maintain a stable electrical connection
• Reduces risk of connector damage that can cause intermittent power or control issues
• Appropriate when the original connector housing is cracked, broken, or missing

• One cover assembly for the connector housing

• Designed to snap or screw into place; follow the appliance wiring diagram and connector alignment
• Disconnect power to the appliance before attempting any repair to avoid shock or injury
• Inspect surrounding wiring and clips; replace damaged wiring or fasteners as needed

This connector assembly secures and drives the freezer drawer bar so the drawer opens and closes smoothly. Replaces a worn or broken bar/gear assembly to restore proper drawer movement and alignment. What it does:

• Transfers drawer motion to the slide mechanism so the freezer drawer glides correctly
• Replaces worn or stripped gears that cause slipping, grinding, or uneven movement
• Secures the drawer bar to the internal slide/track to prevent misalignment or sagging
• Useful when a drawer won't open/close smoothly, catches, or rattles during operation

• Disconnect power before servicing and remove stored items from the drawer
• Generally replaces with basic hand tools; support the drawer while detaching and installing the assembly
• Inspect surrounding slide components for wear and replace if needed for reliable operation

This connector assembly secures and drives the freezer drawer bar so the drawer opens and closes smoothly. Replaces a worn or broken bar/gear assembly to restore proper drawer movement and alignment. What it does:

• Transfers drawer motion to the slide mechanism so the freezer drawer glides correctly
• Replaces worn or stripped gears that cause slipping, grinding, or uneven movement
• Secures the drawer bar to the internal slide/track to prevent misalignment or sagging
• Useful when a drawer won't open/close smoothly, catches, or rattles during operation

• Disconnect power before servicing and remove stored items from the drawer
• Generally replaces with basic hand tools; support the drawer while detaching and installing the assembly
• Inspect surrounding slide components for wear and replace if needed for reliable operation

This spanner is the specialized hand tool used to turn and hold slotted nuts, collars, or fittings on compatible appliances, making service and adjustments easier and safer. It gives a secure grip for loosening or tightening components without damaging surrounding parts. What it does:

• Fits and turns slotted or notched appliance fasteners and collars commonly used in assemblies
• Helps hold a component steady while you loosen or tighten the mating fastener
• Reduces slippage and tool marks compared with pliers or improvised tools
• Useful during maintenance tasks such as removing retaining rings, collars, or adjustable fittings

• One spanner tool

• Disconnect power and/or gas and follow all safety precautions before servicing appliances
• Use the correct size spanner engagement to avoid slipping or rounding the fastener
• Apply steady force; do not use cheater bars or excessive torque unless specified by the manufacturer

Replacement front cover that restores your appliance's exterior finish and helps protect controls and internal components from everyday wear, spills, and minor impacts, delivering a clean, finished look and proper front-panel fit. What it does:

• Covers and protects the appliance's front area, helping shield controls and wiring from dirt and moisture.
• Restores damaged or cracked front trim for improved appearance.
• Helps maintain proper alignment and fit of the front assembly.
• Common symptom: cracked, chipped, warped, or loose front panel that exposes internal parts or looks worn.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Basic hand tools (screwdriver set) may be required to remove the old cover and install the replacement.
• Handle edges carefully to avoid cuts; align tabs/clips and secure fasteners snugly but do not overtighten.

The Water Tank Assembly is an OEM part for LG refrigerators. It stores and supplies water for the refrigerator's dispenser and ice maker, ensuring a steady and clean water flow for these features.

Causes of a bad water tank assembly can include mineral buildup from hard water, leaks due to cracks or punctures, or contamination from mold or bacteria if the tank is not regularly cleaned. Over time, wear and tear from repeated use can also lead to failure.

Symptoms of a bad water tank assembly include:

• Water dispenser not functioning properly
• Reduced or no ice production
• Leaks or puddles inside the refrigerator
• Unpleasant taste or odor in the water

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

The Water Inlet Valve is an OEM part for LG refrigerators. It controls the flow of water into the refrigerator for the ice maker and water dispenser, ensuring a steady and controlled supply of water.

You should replace the water inlet valve if it becomes clogged, damaged, or fails to function properly. Causes of a bad water inlet valve can include mineral buildup from hard water, electrical malfunctions, or general wear and tear over time.

Symptoms of a bad water inlet valve include:

• The ice maker not producing ice
• The water dispenser not dispensing water
• Leaking water from the valve area
• Unusual noises when the valve is operating

This OEM LG part is also compatible with Sears/Kenmore refrigerators.