Parts for Lg LRG3095ST: Door Parts

This truss head tapping screw secures panels, brackets, and covers in your appliance. Replacing a missing or damaged fastener restores a snug fit, reduces vibration, and helps keep components properly aligned for reliable performance.

• Provides low-profile holding power; wide truss head helps secure thin panels and trim
• Replaces lost, stripped, or corroded screws at the original mounting points
• Helps eliminate rattling, vibration, or loose handles/covers
• Addresses situations where a screw will not tighten or backs out during use

• Disconnect power; shut off water/gas if applicable before servicing
• Align parts and hand-start threads to avoid cross-threading
• Tighten until snug; do not overtighten to prevent stripping
• If the receiving hole is damaged, for repair before installing the new screw

This replacement screw secures panels, trim and internal components to restore a tight fit and stop rattling or loose parts. Use it when a missing or stripped screw causes panels or controls to shift. What it does:

• Secures panels, trim pieces or mounting brackets to keep components aligned
• Stops rattling, vibration noise or loose-fitting panels
• Replaces missing or stripped screws to restore proper fastening
• Helps ensure other parts stay in position during normal use

• Disconnect power before working on the appliance to prevent shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and tighten until snug; avoid overtightening which can strip threads or crack plastic
• Replace with the exact OEM screw if available to ensure proper fit and function

This 4.0x16mm tapping screw secures trim and internal components on compatible appliances, providing a reliable fastener for repair or reassembly. Use the correct screw to maintain fit and function during service. What it does:

• Fastens appliance panels, brackets, and small components where a self-tapping thread is required
• Replaces stripped or missing screws that cause loose panels or rattling
• Helps restore proper alignment and secure electrical or mechanical parts
• Suitable where a 4.0 x 16mm size and tapping/sharp thread are specified

• One 4.0x16mm tapping screw (quantity: 1)

• Use the matching screw location and thread engagement; do not force a misaligned fastener
• Tighten until seated; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and follow appliance safety procedures before servicing
• If screws repeatedly strip, inspect mating threads or use an approved repair insert

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

This is a replacement customized screw designed to secure appliance panels and components. It restores proper fit and fastening where the original screw is lost or worn, helping maintain safe, stable operation. What it does

• Replaces missing or damaged mounting screw used on appliance panels and internal components
• Restores secure fastening to reduce vibration and rattling during operation
• Matches the original OEM fit and thread form for correct engagement when verified for your model
• Helps prevent loose parts that can cause noise or interfere with moving components

• Disconnect power and water before servicing the appliance
• Verify screw size, thread direction, and length match the original before installation
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid overtightening to prevent stripping or damaging mating threads

This replacement door handle restores a secure, easy-grip opening to your refrigerator door. It matches the OEM shape and mounting points so the door operates smoothly and looks factory-fresh. What it does:

• Replaces a cracked, loose, or broken refrigerator door handle so the door is easier and safer to open.
• Restores proper grip and leverage for normal daily use.
• Reinstalls to existing factory mounting points to maintain door alignment and appearance.
• Helps prevent further cabinet or door damage caused by using a compromised handle.

• One refrigerator door handle

• Requires removing the old handle and securing the replacement to the same factory screw bosses; use the original screws unless new hardware is explicitly listed.
• Handle hardware may be hidden under trim—check for set screws or clips before prying.
• Support the door while working to avoid strain on hinges; two-person assistance recommended for larger doors.
• Disconnect power only if required for surrounding panels—this is an exterior handle replacement and typically does not require electrical disconnection.

Replacement window glass that restores a clear viewing area in the appliance door and helps maintain a clean, sealed surface. Ideal for replacing cracked, chipped, or cloudy glass to improve visibility and safety. What it does:

• Provides a transparent viewing window so you can monitor cycles without opening the door.
• Replaces cracked, chipped, or fogged glass to restore appearance and function.
• Serves as the door's viewing surface and works with the door assembly and trim.
• Inspect surrounding gaskets, trim, and fasteners when replacing the glass to ensure a proper fit.

• Disconnect power (and water, if applicable) before attempting any repair.
• Wear cut-resistant gloves and eye protection when handling or removing glass.
• Door disassembly and removal of trim or retaining clips is commonly required.
• If the glass is shattered, remove broken pieces carefully and dispose of them per local regulations.

Replacement window glass that restores a clear viewing area in the appliance door and helps maintain a clean, sealed surface. Ideal for replacing cracked, chipped, or cloudy glass to improve visibility and safety. What it does:

• Provides a transparent viewing window so you can monitor cycles without opening the door.
• Replaces cracked, chipped, or fogged glass to restore appearance and function.
• Serves as the door's viewing surface and works with the door assembly and trim.
• Inspect surrounding gaskets, trim, and fasteners when replacing the glass to ensure a proper fit.

• Disconnect power (and water, if applicable) before attempting any repair.
• Wear cut-resistant gloves and eye protection when handling or removing glass.
• Door disassembly and removal of trim or retaining clips is commonly required.
• If the glass is shattered, remove broken pieces carefully and dispose of them per local regulations.

Hinge assembly that secures and pivots the appliance door for smooth, stable operation. Restores proper alignment and sealing to reduce sagging, rubbing, and help the door close evenly. What it does:

• Supports and guides the door pivot to maintain correct opening and closing motion.
• Restores proper door alignment and sealing to improve performance and reduce leaks or cold spots.
• Reduces sagging, rubbing, and noisy or stiff door movement.
• Helps the door latch and close evenly for reliable use.

• Always disconnect power (and water supply, if applicable) before starting repairs.
• Support the door before removing the old hinge to prevent dropping or damage.
• Use appropriate hand tools; avoid forcing parts and do not overtighten fasteners.