Parts for Lg LRG3095ST: Drawer Parts

This factory-specified fastener secures designated panels and components, restoring a precise fit and helping keep your appliance solid and quiet. Replace a missing, stripped, or rusted original with the correct OEM match for the specified locations.

• Secures brackets, panels, and internal parts where this part number is called out
• Replaces damaged, stripped, corroded, or lost screws
• Helps reduce looseness and vibration that can cause rattling noises
• Exact OEM replacement for positions requiring this specific screw

• Disconnect power and shut off water/gas before servicing
• Match to the removed screw and install only in the locations specified for this part number
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening, especially into plastic
• If multiple screws are involved, start all fasteners before final tightening to ensure alignment

This idler bracket mounts the idler pulley or roller in your appliance's tensioning system, keeping a belt or cable aligned and properly tensioned for consistent operation. A bent or worn bracket can cause noise, slippage, or loss of motion.

• Secures the idler pulley/roller in the correct position
• Maintains proper belt/cable tension and alignment
• Helps reduce squealing or squeaking from friction/misalignment
• Can address belts/cables coming off or intermittent movement in the drive mechanism

• Disconnect power; also shut off gas or water before servicing
• Access the tensioner area and note the belt/cable routing and spring orientation
• Relieve tension, remove the old bracket, and transfer the pulley/roller and any spring or hardware as required
• Reinstall the bracket, ensure smooth free movement, route belt/cable correctly, and test operation

This replacement door handle restores a secure, easy-grip opening to your refrigerator door. It matches the OEM shape and mounting points so the door operates smoothly and looks factory-fresh. What it does:

• Replaces a cracked, loose, or broken refrigerator door handle so the door is easier and safer to open.
• Restores proper grip and leverage for normal daily use.
• Reinstalls to existing factory mounting points to maintain door alignment and appearance.
• Helps prevent further cabinet or door damage caused by using a compromised handle.

• One refrigerator door handle

• Requires removing the old handle and securing the replacement to the same factory screw bosses; use the original screws unless new hardware is explicitly listed.
• Handle hardware may be hidden under trim—check for set screws or clips before prying.
• Support the door while working to avoid strain on hinges; two-person assistance recommended for larger doors.
• Disconnect power only if required for surrounding panels—this is an exterior handle replacement and typically does not require electrical disconnection.

This water inlet valve controls water flow to the ice maker and dispenser, restoring proper fill and supply so your refrigerator can make ice and deliver water on demand. Replaces a failed or leaking valve to stop drips and restore normal operation. What it does:

• Opens and closes to allow water into the ice maker and dispenser when requested
• Stops water flow to prevent overfilling and leaking when closed
• Commonly replaces valves that cause no water dispensed, slow fills, or continuous leaking
• Operates as the sealed solenoid valve that the refrigerator's control uses to meter water

• Disconnect power and shut off the water supply before starting any repair
• Replace only with the exact part number shown for fit; secure all water and electrical connections
• After installation, turn on water and power, then check for leaks and proper fill operation

This door handle mounting anchor creates the fixed attachment point on the appliance door or drawer. Replacing a worn or missing anchor restores a solid, wobble-free handle and a consistent feel when opening and closing.

• Provides the secure mounting point that the handle fastens to
• Helps keep the handle aligned and rigid during use
• Replace if the anchor is cracked, stripped, or missing
• Resolve a loose/wobbly handle, a handle that won't tighten, or misalignment after service

• Disconnect power; turn off the water supply
• Protect the door/drawer finish and support the handle during removal
• Remove the handle per your model's instructions and take out the damaged anchor
• Install the new anchor using the existing mounting location/hardware, seat the handle fully, then tighten set screws evenly without overtightening

This parts assembly is a replacement module that restores the specific component group in compatible LG appliances, helping return the affected feature to normal operation. Use it to replace a worn or failed factory assembly. What it does

• Replaces a multi-piece component assembly used in the appliance's subsystem.
• Restores function when the original assembly shows signs of failure or intermittent operation.
• Common symptoms it can address: subsystem not responding, intermittent errors, or a feature that no longer operates reliably.
• Designed to match the original OEM form and connectors for a direct replacement.

• Disconnect power and water before starting any service.
• Handle connectors and wiring carefully; match connectors and routing to avoid pin damage or misalignment.
• Reuse factory mounting hardware unless replacement fasteners are required.
• Follow the OEM instructions for safe, correct installation.