Parts for Maytag AGR4230BAB1: 07 - Door Parts

Color: White. Size: 8-18 x 3/8 inch.

Screw for side trim.

This replacement door liner is the inner panel that restores a refrigerator door's interior surface for proper shelf mounting and sealing. It provides a clean, durable surface to support door bins and help maintain the fridge interior. What it does

• Replaces a cracked, warped or damaged inner door panel so shelves and bins sit securely
• Restores a smooth, food-safe surface that helps keep stored items contained
• Helps maintain proper door fit and consistent cold-air retention when used with intact gaskets
• Compatible with OEM mounting points for straightforward fitment when matched to the correct model

• One inner door liner/panel

• Remove contents and door shelves/bins before replacing the liner
• Use recommended screws/clips from the original door; only install if fasteners are present and undamaged
• If door gasket or shelves are damaged, replace them separately for best performance
• Disconnect power to the appliance and follow safe lifting practices when removing/reinstalling the door

This push-on nut is a press-fit retainer that secures components to a smooth shaft or stud. Use it to restore a tight, reliable hold when the original fastener is missing, bent, or no longer grips securely.

• Provides a friction hold on a shaft or stud to keep parts from sliding off
• Helps reduce wobble, vibration, or rattling caused by a loose or missing retainer
• Common signs of failure: component won't stay in place, falls off, or feels loose
• Direct replacement for a deformed or lost push nut

• Disconnect power and shut off gas/water before servicing
• Remove the old retainer carefully; do not reuse a distorted push nut
• Align and press the new push nut straight onto the shaft/stud; a deep socket can help apply even pressure
• Verify full engagement; do not hammer near glass, porcelain, or delicate surfaces

This appliance screw secures panels, brackets, and internal components. Replacing a stripped or missing screw keeps parts tight and aligned, reducing vibration and preventing noise for reliable day-to-day operation.

• Secures mounting points for panels, brackets, or assemblies
• Replaces stripped, rusted, or missing hardware to restore a solid attachment
• Helps reduce rattling, vibration, and misalignment from loose fasteners
• Maintains proper fit so components operate as intended

• Disconnect power; turn off water or gas before service
• Match the screw to its original location and replace one at a time
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver type/size specified for your model

This door hinge lets the refrigerator door pivot smoothly and stay aligned for proper sealing and cooling. Replaces a worn or damaged hinge to restore correct door fit and reduce rubbing or sagging. What it does:

• Provides the pivot point that allows the refrigerator door to open and close
• Keeps the door aligned to maintain a tight seal and proper cooling
• Helps eliminate sagging, rubbing, or uneven door movement
• Can be the cause of noisy or stiff door operation when worn

• One door hinge

• Disconnect power to the appliance before starting any repair
• Use proper tools and retain all original mounting hardware
• Two people may be needed to support the door during removal and reinstallation
• Check door alignment and seal after installation; adjust as required per manufacturer instructions

This outer door panel replaces a damaged, dented or cosmetic-worn oven or appliance door panel to restore the door's appearance and protective surface. It gives your appliance a finished look and protects inner components from everyday wear. What it does

• Replaces a cracked, dented or scratched outer door surface
• Restores the appliance's finished appearance and curb appeal
• Protects the inner door assembly and insulation from damage
• Helps maintain a proper seal and alignment when installed correctly

• Disconnect power to the appliance before starting work.
• Handle panel edges carefully to avoid cuts or damage to the finish.
• Installation typically requires removing the door and fastening with existing screws; keep original hardware unless purchasing replacements.
• If the door has glass or insulation removed during service, inspect for damage and follow manufacturer instructions when reassembling.

Replacement screw used to secure components and panels in household appliances, restoring proper fit and effectively reducing movement or rattling from loose or missing fasteners. What it does:

• Secures panels, trim and internal components to keep parts aligned and stable.
• Helps stop rattling, vibration or noise caused by loose or missing fasteners.
• Restores proper mounting for brackets, covers and control housings.
• Useful wherever a worn or stripped screw is causing play or loose parts.

• Disconnect power and unplug the appliance before doing any work.
• Use the correct driver and size to avoid stripping the head or threads.
• Tighten snugly but avoid overtightening—replace with the exact OEM screw when specified.