Parts for Maytag JIS1450DS1: 05 - Door Parts

This trim vent replaces a damaged or worn vent grille to restore proper airflow appearance and help direct air where the appliance needs it. It's a direct-replacement exterior trim piece that cleans up the unit's vent opening. What it does:

• Covers and protects the appliance vent opening while providing a finished appearance
• Directs airflow and helps prevent debris from entering the vent area
• Replaces cracked, broken, or faded vent trim that affects appearance or fit
• Helps reduce rattling or loose trim that can occur with damaged vent pieces

• One trim vent (single grille piece)

• Disconnect power to the appliance before beginning any work
• Typically installs with snap-in tabs or a few screws; avoid forcing to prevent breakage
• Inspect surrounding clips or screws and replace if worn for a secure fit

This replacement door handle restores a secure grip and proper function to the refrigerator door so it opens and closes smoothly. It matches OEM fit and appearance for direct replacement on compatible units. What it does:

• Replaces a cracked, broken, or loose refrigerator door handle
• Restores secure, comfortable grip for opening and closing the door
• Helps keep the door aligned and sealing properly when latched
• Matches original fit and mounting points for easy swap-out

• Disconnect power to the appliance before beginning any repairs when applicable
• Remove any trim or screws that secure the old handle; keep original fasteners unless new hardware is supplied
• Align handle with mounting holes and tighten fasteners securely but do not overtighten

Color: Stainless

This door liner is the oven's inner door panel that helps protect the door cavity and support the inner glass. Replaces a damaged or worn liner to restore a clean interior surface and proper glass fit. What it does:

• Replaces the oven's inner door panel that secures the inner glass and insulation
• Restores a sealed, smooth interior door surface to help contain heat and cooking messes
• Helps eliminate rattles or misalignment caused by a cracked or bent liner
• Compatible with ovens that specify part number W10902192

• One inner oven door liner

• Refer to the oven model's service manual for step-by-step disassembly and reassembly
• Disconnect power (and gas if applicable) before starting work
• Handle the glass and liner carefully—wear gloves and eye protection to avoid cuts
• If other door components are damaged, inspect and replace them as needed for a complete repair

This factory fastener secures appliance panels, brackets, and internal components. Replacing a missing, stripped, or corroded screw restores proper fit and stability, helping reduce vibration, rattling, and wear during everyday operation.

• Secures covers, brackets, and assemblies to the cabinet or frame
• Restores alignment to reduce gaps, looseness, and vibration
• Replaces lost, damaged, corroded, or stripped hardware
• Matches the original fastener for correct fit and retention

• Disconnect power and shut off water or gas before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Tighten snugly—do not overtighten to prevent thread or plastic damage
• Inspect receiving threads or clips; repair/replace if stripped or broken

The Door Glass is an OEM replacement part for Whirlpool ranges. It provides insulation and protection for the oven cavity and maintains the proper temperature inside the oven while allowing you to visually check on your dishes without opening the door.

Symptoms of a faulty inner door glass include:

• Cracks or shattered glass
• Foggy or discolored appearance
• Heat escaping from the oven

A bad inner door glass can occur due to accidental damage, extreme temperatures, or regular wear and tear. If you notice signs such as cracks, shattered glass, or foggy appearance, it may be time to replace the inner door glass.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

A replacement door hinge that restores proper door alignment and smooth opening and closing. Replaces worn or damaged hinges to help stop door sagging, binding, or poor sealing for safer, reliable operation. What it does:

• Provides the pivot and support that lets the appliance door open and close smoothly.
• Replaces a worn or broken hinge to correct door sag, binding, or uneven gaps.
• Restores proper door sealing and alignment to improve operation and reduce leaks or drafts.
• Matches the form and function of the original hinge.

• Unplug the appliance or disconnect power before starting any repair.
• Support the door while removing/installing the hinge to prevent dropping; have an assistant if needed.
• Use the appropriate hand tools; reuse original fasteners if replacement hardware is not provided.
• After installation, check alignment and operation; tighten fasteners securely but avoid over-torquing.

This mounting bracket secures and supports appliance panels and internal components to keep assemblies aligned and stable during operation. It restores proper fit and prevents excessive vibration or movement in the affected area. What it does:

• Provides a sturdy attachment point for cabinet panels and internal parts
• Helps maintain correct alignment to reduce rattling and vibration
• Restores secure mounting after damage, wear, or during reassembly
• Commonly used when panels are loose, misaligned, or produce noise

• One mounting bracket

• Turn off and unplug the appliance before beginning any repairs
• Verify bracket orientation and fastener locations match the removed part
• Use the original screws or OEM-recommended fasteners; replace any stripped hardware

This is a genuine replacement mounting screw used to secure appliance panels and components. It restores proper fastening to reduce vibration and prevent parts from loosening during normal operation. What it does:

• Secures panels, brackets, or trim to the appliance frame
• Prevents rattling or vibration caused by loose fasteners
• Keeps wiring and small components held in place
• Helps maintain proper alignment of removable parts

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Start threads by hand, then tighten until snug; do not overtighten
• Keep removed fasteners organized to ensure correct reassembly

This glass bracket secures the oven/microwave door glass, keeping the inner glass panel aligned and stable for safe operation. It replaces worn or damaged brackets to restore proper door fit and reduce rattling. What it does:

• Secures and supports the door's inner glass panel to maintain alignment
• Prevents glass movement that can cause vibration, noise, or improper sealing
• Helps restore proper door closing and even heat retention when functioning parts are present
• Commonly replaced when bracket is cracked, bent, or missing mounting integrity

• One glass bracket

• Disconnect power to the appliance before beginning any repair
• Handle glass carefully; wear cut-resistant gloves and eye protection
• Installation typically requires partial door disassembly and removal of retaining screws—keep track of fasteners

The Screw is an OEM part for Whirlpool ranges. This screw is used to secure various components within the range, ensuring that parts such as panels, control boards, or burners are firmly attached and remain stable during operation.  

Causes of a bad range screw can include regular wear and tear, over-tightening, or exposure to high heat.  

Symptoms of a bad range screw include:

• Loose or unstable components within the range
• Difficulty in securing parts during maintenance or repair
• Visible damage or wear on the screw
• Parts becoming misaligned or rattling during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement screw secures appliance components and panels. Replacing worn or missing hardware restores a tight, rattle-free fit and helps keep assemblies properly aligned for reliable performance.

• Fastens panels, brackets, or covers to the appliance frame or mating parts
• Helps maintain proper alignment and reduces vibration and noise
• Replaces missing, stripped, or corroded screws
• Common signs to replace: loose or rattling panels, misaligned parts, damaged screw head or threads

• Disconnect power; also shut off water or gas to the appliance if applicable
• Compare to the original to ensure thread and length match before installing
• Start threads by hand to avoid cross-threading; tighten only until snug
• If the mating clip/insert is stripped, replace that hardware as well