Parts for Frigidaire FGEF304DKWB: 09 - Doors Parts

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This heat-resistant insulation helps contain oven heat and shield surrounding components. Replacing worn insulation supports faster, more consistent preheating, steadier baking temperatures, and cooler exterior panels for safer, more efficient operation. What it does:

• Wraps/lines the oven cavity or panels to reduce heat loss and protect nearby wiring and controls
• Helps the oven preheat efficiently and maintain consistent cooking temperatures
• Limits heat transfer to exterior panels and surrounding cabinetry
• Common signs of failure: longer preheat times, temperature swings, unusually hot sides/back, or insulation that is burnt, brittle, soaked, or missing

• 1 insulation piece

• Disconnect power and, if applicable, shut off gas before servicing
• Access typically requires removing rear/side panels or sliding the unit out; take photos to aid reassembly
• Wear gloves and a dust mask; handle gently—do not compress insulation and keep clear of sensors/wiring
• Re-secure with original clips/tape, reinstall panels, then test preheat and check for abnormal exterior heat

The Inner Door Glass is an  OEM replacement part for Frigidaire ranges. It is responsible for providing a safe viewing window into the oven cavity while protecting interior components from external damage.  

Causes of a bad inner door glass include normal wear and tear such as chips or cracks developing from years of use. Accidental impact or thermal shocks from sudden temperature changes can also compromise the integrity of the glass.

Symptoms of a bad inner door glass:

• Cracks or breaks visible in the glass
• Difficulty seeing into the oven cavity clearly 
• Increased risk of heat escaping when the oven is in use
• Potential safety hazards if glass cracks or shatters  

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.

This replacement mounting screw secures appliance panels and components to restore stable assembly and reduce rattling or loose parts. It's a direct-fit fastener used where the original screw has become stripped, lost, or damaged. What it does:

• Secures panels, brackets, or components to restore proper fit and alignment
• Stops vibration and rattling caused by loose or missing screws
• Replaces stripped, corroded, or worn fasteners to prevent further damage
• Matches OEM fit for reliable, long-term fastening when installed correctly

• One replacement mounting screw

• Use the matching driver or socket; avoid over-tightening to prevent stripping
• Power tools may be used on low torque settings; finish tightening by hand for best control
• Disconnect power before accessing internal components on electrical appliances
• If threads are damaged, replace the mating nut or tapped component as needed

This replacement screw secures appliance components and panels. Restore a snug, factory fit when original hardware is missing or stripped, helping prevent rattles, vibration, and misalignment so your unit operates safely and quietly.

• Fastens panels, brackets, or internal parts to the cabinet or frame
• Replaces missing, rusted, or stripped screws
• Helps correct loose or misaligned components
• Reduces rattling or vibration noises caused by loose hardware

• Disconnect power to the appliance before servicing
• Replace one screw at a time to maintain alignment
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; repair damaged threads or replace related clip/insert if needed

This replacement part is a gasket seal, and it is intended for use on ranges and ovens. This is a genuine replacement part made by Frigidaire. This gasket is an important part of any range or oven. This part is used around the opening of the oven so that it is sealed when in use to prevent heat loss while cooking. A new gasket seal might be needed if the current one is visibly falling off, frayed, or not attached anymore. This is a genuine OEM replacement part and is sold individually.

This glass spacer positions and cushions refrigerator glass components to maintain proper spacing and reduce rattling or contact damage. It restores correct alignment for secure, quiet operation and helps prevent chipping or glass stress. What it does:

• Keeps glass shelves/panels separated and aligned to prevent rubbing, chipping, or cracking.
• Cushions impact and dampens vibration that can cause rattling or noisy doors/drawers.
• Helps maintain proper spacing for smooth insertion and removal of shelves or panels.
• Replaces worn, cracked, or missing spacers that allow glass movement or uneven seating.

• One glass spacer

• High-level replacement only; confirm spacer orientation and seating before final assembly.
• Handle glass and spacer carefully; wear gloves and eye protection to avoid cuts.
• Do not overtighten nearby fasteners—secure snugly to avoid cracking the glass.
• Replace the glass panel before installing the spacer if damaged or fractured.

The Handle is an OEM replacement part for Frigidaire ranges. It is the component located on the front of the oven that allows for opening and closing the oven door.

Causes of a bad handle stem primarily from wear and tear due to frequent use over many years. Exposure to heat cycling may also degrade adhesives or secondary components that secure the handle.

Symptoms of a faulty handle include:

• Difficulty opening or closing the oven door
• The handle detaching from the door
• Sharp edges or broken pieces that compromise safety
• Loss of grip or stability while moving the door

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This support bracket secures and stabilizes appliance components, restoring proper alignment and stopping movement. It's a simple replacement that helps reduce rattling and prevents panels or assemblies from shifting during use. What it does:

• Provides a rigid mounting point to hold panels, trim, or internal assemblies in place
• Restores proper alignment when a worn or broken bracket causes gaps or looseness
• Reduces vibration and rattling caused by a damaged or missing support
• Keeps connected parts from shifting, which can prevent further wear or damage

• Disconnect power to the appliance before beginning any repair
• Verify the bracket orientation and fit against the mating surface before fastening
• Use the factory screw locations and hardware; tighten screws securely but avoid over-torquing

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

Specs: 8 - 18 x 0.500

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts

This is a replacement adhesive label used to restore legible identification or instruction markings on the appliance. Replacing a damaged or missing label helps keep model, rating and safety information readable for service and ownership. What it does

• Restores faded, torn or missing identification and rating information
• Makes model/serial and safety markings easy to read during service
• Helps ensure important usage or caution text remains visible
• Prevents further wear where original adhesive label has peeled

• One replacement adhesive label

• Install on a clean, dry surface; wipe area with isopropyl alcohol and let dry before applying
• Align carefully—adhesive is permanent and difficult to reposition once set
• Use gloves to avoid contaminating the adhesive or leaving fingerprints
• Disconnect power before working in the area