Parts for Frigidaire LC120JW5: 04 - Dryer Motor, Base, Housing And Moun Parts

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

This is a replacement fastening screw used to secure panels, trim or components on compatible appliances. It restores proper fit and helps eliminate loose or rattling parts for a safe, tidy repair. What it does:

• Secures panels, trims or small components in place
• Stops loose parts that can vibrate or rattle during operation
• Replaces missing or stripped screws that prevent components from seating correctly
• Helps maintain alignment of assembled parts to reduce wear or gaps

• Unplug or disconnect power to the appliance before starting any repair
• Use the matching screwdriver or driver bit to avoid cam-out and damage
• Install by hand until threads engage, then tighten snugly—do not overtighten
• If threads are damaged or the screw won't hold, replace with correct OEM part

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

Hex washer head ,10-32 x 0.375. Ground

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

The Terminal Block Kit is an OEM part for Frigidaire appliances, typically used for connecting house power to various electrical appliances like ranges and dryers. This kit includes includes screws, nuts, and a unique terminal block. It plays a critical role in the power supply system by providing a reliable connection point for the appliance's main power cord, preventing loose connections and potential electrical hazards.

Symptoms of a bad Terminal Block Kit include:

• Signs of burning or melting at the connection points,
• Flickering power or intermittent operation of the appliance,
• A burning smell from the appliance area.

Causes of terminal block failure often involve loose connections that can lead to arcing and overheating, improper installation, or general wear and tear that degrades the integrity of the electrical contacts.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Hex washer head ,10-32 x 0.375. Ground

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

This is a replacement fastening screw used to secure panels, trim or components on compatible appliances. It restores proper fit and helps eliminate loose or rattling parts for a safe, tidy repair. What it does:

• Secures panels, trims or small components in place
• Stops loose parts that can vibrate or rattle during operation
• Replaces missing or stripped screws that prevent components from seating correctly
• Helps maintain alignment of assembled parts to reduce wear or gaps

• Unplug or disconnect power to the appliance before starting any repair
• Use the matching screwdriver or driver bit to avoid cam-out and damage
• Install by hand until threads engage, then tighten snugly—do not overtighten
• If threads are damaged or the screw won't hold, replace with correct OEM part

A small threaded fastener used to secure components to shafts or hold assemblies together. This set screw restores proper fit and helps stop slipping, rattles, or misalignment caused by a loose fastener. What it does:

• Secures pulleys, collars, knobs, or other components to a shaft to prevent movement
• Stops slipping and eliminates related noise or vibration when tightened properly
• Maintains alignment of moving parts to preserve smooth operation
• Simple replacement for applications where the original set screw is worn or missing

• One set screw

• Disconnect power to the appliance before starting any repair
• Use the correct driver or hex key to avoid rounding the head
• Tighten until snug; avoid overtightening which can strip threads or break the screw
• If the screw fastens a rotating part, test operation at low speed after installation

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten