Parts for Frigidaire LC248H1: 05 - Dryer Motor, Blower And Belt Parts

A small threaded fastener used to secure components to shafts or hold assemblies together. This set screw restores proper fit and helps stop slipping, rattles, or misalignment caused by a loose fastener. What it does:

• Secures pulleys, collars, knobs, or other components to a shaft to prevent movement
• Stops slipping and eliminates related noise or vibration when tightened properly
• Maintains alignment of moving parts to preserve smooth operation
• Simple replacement for applications where the original set screw is worn or missing

• One set screw

• Disconnect power to the appliance before starting any repair
• Use the correct driver or hex key to avoid rounding the head
• Tighten until snug; avoid overtightening which can strip threads or break the screw
• If the screw fastens a rotating part, test operation at low speed after installation

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

This small retainer clip secures trim and components to the appliance chassis, keeping panels and assemblies properly seated for quiet, reliable operation. It's a simple replacement that restores secure fastening where the original clip has broken or worn. What it does

• Holds panels, trim pieces, or small assemblies in place to prevent looseness and rattling
• Replaces a broken, bent, or missing clip that allows parts to shift during use
• Helps maintain proper alignment of adjacent components for smooth operation
• Works where a firm, non-permanent fastener is required

• One retainer clip

• Disconnect power before servicing any appliance to avoid shock or injury
• Access the clip location by removing the appropriate trim or panel per your model's service instructions
• Use needle-nose pliers or a flat screwdriver to remove the old clip and press the new clip into place until it seats securely

This is a replacement fastening screw used to secure panels, trim or components on compatible appliances. It restores proper fit and helps eliminate loose or rattling parts for a safe, tidy repair. What it does:

• Secures panels, trims or small components in place
• Stops loose parts that can vibrate or rattle during operation
• Replaces missing or stripped screws that prevent components from seating correctly
• Helps maintain alignment of assembled parts to reduce wear or gaps

• Unplug or disconnect power to the appliance before starting any repair
• Use the matching screwdriver or driver bit to avoid cam-out and damage
• Install by hand until threads engage, then tighten snugly—do not overtighten
• If threads are damaged or the screw won't hold, replace with correct OEM part

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This lock washer secures fasteners and helps keep appliance panels and components from loosening during normal use, restoring a stable connection and reducing rattles or movement. What it does

• Grips under a screw or bolt to resist loosening from vibration and thermal cycling
• Helps keep panels, brackets, and small components securely fastened
• Commonly used where a screw or bolt must stay tight despite vibration
• Can reduce rattling noises and intermittent loose-part symptoms

• Disconnect power to the appliance before beginning any repair
• Replace with the same type and orientation of washer for proper locking action
• Use appropriately sized screw or bolt; do not mix with mismatched hardware
• Hand-start fasteners, then tighten to snug fit—avoid over-tightening which can deform the washer

This is a replacement fastening screw used to secure panels, trim or components on compatible appliances. It restores proper fit and helps eliminate loose or rattling parts for a safe, tidy repair. What it does:

• Secures panels, trims or small components in place
• Stops loose parts that can vibrate or rattle during operation
• Replaces missing or stripped screws that prevent components from seating correctly
• Helps maintain alignment of assembled parts to reduce wear or gaps

• Unplug or disconnect power to the appliance before starting any repair
• Use the matching screwdriver or driver bit to avoid cam-out and damage
• Install by hand until threads engage, then tighten snugly—do not overtighten
• If threads are damaged or the screw won't hold, replace with correct OEM part

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Hex washer head ,10-32 x 0.375. Ground

Tub to pressure switch hose.

This block is a small mounting spacer used to secure and align components inside the appliance, helping maintain proper fit and operation. It replaces worn or broken mounting blocks to restore stable support and alignment. What it does:

• Provides a stable mounting surface or spacer between cabinet components
• Holds panels or assemblies in correct position to prevent rubbing or misalignment
• Helps reduce vibration or shifting of the connected parts during operation
• Commonly replaced when cracked, broken, or missing

• One mounting block

• High-level replacement; may require removing panels or trim to access mounting location
• Use appropriate hand tools and keep fasteners organized for reassembly
• Disconnect power before servicing any electrical components

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener