Parts for Frigidaire LCE441PW1: 04 - Dryer Motor, Blower And Belt Parts

Dryer not heating or taking too long to dry? A damaged blower wheel restricts airflow. This replacement part restores proper air circulation.

A small threaded fastener used to secure components to shafts or hold assemblies together. This set screw restores proper fit and helps stop slipping, rattles, or misalignment caused by a loose fastener. What it does:

• Secures pulleys, collars, knobs, or other components to a shaft to prevent movement
• Stops slipping and eliminates related noise or vibration when tightened properly
• Maintains alignment of moving parts to preserve smooth operation
• Simple replacement for applications where the original set screw is worn or missing

• One set screw

• Disconnect power to the appliance before starting any repair
• Use the correct driver or hex key to avoid rounding the head
• Tighten until snug; avoid overtightening which can strip threads or break the screw
• If the screw fastens a rotating part, test operation at low speed after installation

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Replaces missing, stripped, or rusted 8-18 thread screws that secure dryer panels, brackets, and components for tight, rattle-free assembly.

This lock washer secures fasteners and helps keep appliance panels and components from loosening during normal use, restoring a stable connection and reducing rattles or movement. What it does

• Grips under a screw or bolt to resist loosening from vibration and thermal cycling
• Helps keep panels, brackets, and small components securely fastened
• Commonly used where a screw or bolt must stay tight despite vibration
• Can reduce rattling noises and intermittent loose-part symptoms

• Disconnect power to the appliance before beginning any repair
• Replace with the same type and orientation of washer for proper locking action
• Use appropriately sized screw or bolt; do not mix with mismatched hardware
• Hand-start fasteners, then tighten to snug fit—avoid over-tightening which can deform the washer

This small retainer clip secures trim and components to the appliance chassis, keeping panels and assemblies properly seated for quiet, reliable operation. It's a simple replacement that restores secure fastening where the original clip has broken or worn. What it does

• Holds panels, trim pieces, or small assemblies in place to prevent looseness and rattling
• Replaces a broken, bent, or missing clip that allows parts to shift during use
• Helps maintain proper alignment of adjacent components for smooth operation
• Works where a firm, non-permanent fastener is required

• One retainer clip

• Disconnect power before servicing any appliance to avoid shock or injury
• Access the clip location by removing the appropriate trim or panel per your model's service instructions
• Use needle-nose pliers or a flat screwdriver to remove the old clip and press the new clip into place until it seats securely

Replaces missing, stripped, or rusted 8-18 thread screws that secure dryer panels, brackets, and components for tight, rattle-free assembly.

This replacement door gasket creates a tight seal around the refrigerator door to help keep cold air in and warm air out, protecting food and improving cooling consistency. What it does:

• Seals the door to reduce air leaks and prevent temperature fluctuations
• Helps stop frost and moisture buildup inside the fresh-food compartment
• Restores proper door closing and alignment when worn or torn
• Can reduce compressor run-time caused by air infiltration

• Disconnect power to the appliance before starting any work.
• Remove the old gasket and clean the channel before installing the new gasket.
• Start installing at one corner and work around the door, ensuring the gasket seats fully in the channel.
• If needed, gently warm the gasket to increase flexibility for an easier fit (use low heat and caution).

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

Protects the power cord where it passes through the washer cabinet. Replace if cracked, worn, or missing to prevent cord chafing and wire exposure.

Suspension spring for washer dryer combo units. Supports the drum and absorbs vibration during wash and spin cycles. Replace if stretched, broken, or missing.

Dryer buzzer that signals when the drying cycle is complete. Replace if the buzzer sounds weak, distorted, or fails to alert you at cycle end.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Hex washer head screw for washers and laundry centers. Replaces missing, stripped, or damaged screws during repairs or component replacement.

Pressure tube connects washer tub to water level switch. Replace if cracked, kinked, or clogged to restore proper water level sensing in your laundry center.