Parts for Lg WM3477HW: Dryer Parts

This duct outlet directs a dryer's exhaust from the cabinet to the external vent, helping maintain proper airflow and reduce leaks. It replaces a damaged or worn outlet flange to restore safe venting. What it does:

• Channels dryer exhaust from the cabinet to the vent hose or duct
• Helps maintain proper airflow for efficient drying
• Prevents exhaust leaks that can cause poor performance or odors
• Reduces rubbing/interference that can create noise when damaged

• One duct outlet

• Disconnect power before servicing; for gas dryers, turn off the gas supply and disconnect per local codes
• Use basic hand tools; avoid bending the outlet flange to prevent cracks
• Verify a secure seal with the vent hose after installation and test operation

This DC fan motor assembly restores fan-driven airflow and circulation in compatible appliances, helping return normal cooling and ventilation performance. Use it to replace a failed or noisy fan motor for more reliable operation. What it does:

• Drives the appliance fan to maintain proper air circulation for cooling or ventilation.
• Replaces a motor that has stopped running, helping address reduced or no airflow.
• Can resolve loud, grinding, or rattling noises coming from the fan area.
• Help with inconsistent or warmer-than-normal temperatures caused by a failed fan.

• Disconnect power before starting — unplug the appliance or switch off the breaker.
• Photograph wiring and panel locations before removal to ensure correct reconnection.
• Handle sharp sheet metal and evaporator/coil areas with care; use gloves as needed.
• Verify the part number on your appliance and compare connectors and mounting before installation.

This door gasket seals the refrigerator door to keep cold air in and maintain consistent temperatures. Replaces a worn or damaged seal to help reduce energy loss, frost buildup, and moisture inside the compartment. What it does:

• Creates an airtight seal between the door and cabinet to retain cold air.
• Helps prevent warm air infiltration that can cause temperature swings and food spoilage.
• Reduces condensation, frost buildup, and excess cycling of the compressor.
• Restores proper door closing and helps improve overall cooling efficiency.

• High-level swap: remove the old gasket and press or screw the new gasket into the door channel per OEM instructions.
• Inspect mounting channel and hinge alignment before installation; realign door if it does not seat evenly.
• If gasket appears loose after installation, warm gently and refit to improve sealing.
• Disconnect power only if instructed by the OEM for access; otherwise follow basic electrical safety and wear gloves as needed.

This Thermostat Assembly monitors and regulates internal temperature within the appliance's heating circuit. Replacing a failed thermostat restores proper heat control, helps prevent overheating, and can resolve common heating performance issues so cycles run correctly. What it does

• Senses internal temperature and opens/closes the heater circuit to maintain proper heat
• Provides over-temperature protection by cutting power at unsafe temperatures
• Helps ensure consistent heating performance throughout the cycle
• Helps with symptoms such as no heat, overheating/shutting off, or unusually long cycle times

• 1 thermostat assembly

• Disconnect power before servicing; allow hot components to cool
• Access the thermostat location (varies by model); note wire positions before removal
• Mount flush to the surface for accurate sensing; transfer original hardware if required
• After installation, test operation; use a multimeter for continuity checks if needed

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

This wire harness routes power and signals between the washer's control and multiple components. Replace a damaged harness to restore dependable operation when wiring is cut, brittle, or connectors are heat-damaged or corroded.

• Distributes electrical power and communication between the control board and components such as the motor, pump, valves, door lock, and sensors
• Maintains safe, reliable connections when insulation and terminals are intact
• Typical failure signs: intermittent operation, no start, specific loads not working (pump/motor/valves), or error codes traced to wiring faults
• Visible damage like chafed wires, broken connector locks, or burned/corroded terminals indicates replacement

• Disconnect power and turn off water supply before servicing; wear cut-resistant gloves
• Photograph and label connectors; move one plug at a time from old to new to avoid miswiring
• Route along original clips, channels, and grommets; keep wiring clear of sharp edges and moving parts
• Ensure all connectors are fully seated; test operation before final reassembly