Parts for White Outdoor 132-455F190 / 1992: Engine, Lower Deck & Drive System Parts

This hex washer screw is a genuine OEM replacement part for a variety of household and outdoor appliances. A hex washer screw is a self-piercing screw with an attached washer at the head of the screw. Self-piercing screws are quite sharp and feature a twin-lead thread to screw into a surface more effectively. The built-in hexagonal washer helps to balance weight and force throughout the connection and prevent breakage. Hex washer screws can become damaged over time through repeated stress or tension. Their threading can become stripped or the head can eventually snap off. Replacing a hex washer screw is simple as long as you have the right tool. The unique shape of the screw head makes it incompatible with a flathead or Phillips head screwdriver. Instead, replacing this type of screw requires a unique hex head screwdriver. This part is compatible with Yard Machines, MTD, Yard Man, Troy-Bilt, and Craftsman products and will fit lawn mowers, tractors, snowblowers, vacuums, and chippers. This is a high-quality replacement part sourced from the original manufacture and ships independently of any other hardware.

This bell washer is a genuine MTD part, sold individually. This bell washer can be used as a replacement part for a lawn tractor, chipper shredder, tiller, or lawnmower. This bell washer adds spacing on a shaft in the tool.If the user of the appliance notices that a washer is missing, it should be replaced. General wear and tear is very normal for outdoor appliances, and if it occurs, the washer should be removed and replaced with this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bell washer is compatible with the following outdoor appliance brands: MTD, Yard Man, Yard Machines, and Troy-Bilt.

This spring washer has a conical shape with an open center. It has a shape like a traditional washer but is smaller than a typical coiled spring. These washers can handle a larger load than a coiled spring and are used in lawn and garden equipment to cushion heavy loads. Over time, these washers can experience wear and tear which will lead to damage or breakage. When this occurs, the spring washer will need to be replaced.Visually inspect the spring washer for damage like scratches, breaks, and dents. If these occur or the washer is warped, it needs to be replaced. The process involves removing the nut or screw above the washer with a screwdriver or other tool. After accessing the spring washer, it can be removed and a replacement part can be added to the equipment. Reassemble the parts and the equipment should work again.This is a genuine OEM spring washer replacement part that is sold individually. It's sourced directly from the manufacturer. It is compatible with lawnmowers, wood chippers, snowblowers, log splitters, tillers, chainsaws, string trimmers, and edgers by Craftsman, MasterCut, Toro, Turf King, Cub Cadet, Yard-Man, Ryobi, Bolens, Husky, Montgomery Wards, Murray, Huskee, Yard Machines, and MTD.

This is a hex screw used on a variety of types of lawn and garden equipment. On large machinery, it is often used to mount the gas tank. On smaller items, it tends to be used to clamp the housing together. It can secure items like plastic, metal, brick, and wood together. It measures 5/16-18 x .75 inches and is made of durable metal. In some cases, the screw can become damaged, broken, or stripped, which means it needs to be replaced.A visual inspection will indicate whether the screw is damaged. If it needs to be replaced, a hex wrench can be used to remove it from the equipment. Afterward, the replacement hex screw can be installed with the wrench before being tightened to ensure materials hold together well.This hex screw is a genuine OEM part that is sold individually. It is sourced directly from the manufacturer. The hex screw is compatible with lawnmowers, wood chippers, log splitters, snowblowers, chainsaws, edgers, tillers, leaf blowers, and string trimmers by Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Husky, Broan, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Turf King, Yard-Man, and MasterCut.

This hex screw is a genuine MTD part, sold individually. A hex screw can be used as a replacement part for outdoor appliances including lawn mowers, snowblowers, tillers, and wood chippers. This genuine OEM part is a small fastening component.The hex screw in a outdoor appliance might need to be replaced if it has been lost or damaged. If the screw has been damaged and cannot serve its typical function, it should be removed and replaced by this genuine OEM replacement part in a timely fashion.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This hex screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Husky, Yard Machines, Huskee, Montgomery Wards, Yard Man, and MasterCut.

This hex nut is designed for use with select trimmers and mowers. It is a standard hardware part that may have multiple applications depending on the type of unit and model. The nut is typically used to secure engine components or housing elements to provide safe use of the machine. These nuts are durable, but they are small and can become lost during other repairs. The constant exposure to vibrations and use can also cause them to strip or become damaged over time. Either way, a replacement with this genuine hex nut will resolve the issue and get equipment back in working order. This genuine OEM hex nut is manufactured to exact standards and sourced from the manufacturer. It can be used with trimmers and mowers from RYOBI, MTD, Bolens, Troy-Bilt, Yard Machines, Huskee, Yard Man, and Cub Cadet. Check the parts diagram for exact application and location of this nut and note that it may have multiple uses on select models. This hex nut is sold individually, and additional nuts will require the purchase of multiple pieces. In order to replace this nut, a hex socket wrench and driver will be required. Always wear gloves for safety.

This variable speed pulley is a genuine MTD part, sold individually. This variable speed pulley can be used as a replacement part in a lawn mower. The purpose of a variable speed pulley in a lawn mower is to regulate and manage the speed at which the motor runs so that the speed can be kept within a stable range for the safety of the operator of the appliance.The variable speed pulley in a lawn mower might have to be replaced if the variable speed pulley can no longer properly manage the speed of the lawn mower. This could occur if the variable speed pulley suffers damage from general wear and tear with long-term use or as the result of an accidental collision with a hard object that warps the variable speed pulley beyond functionality. This replacement should be executed in accordance with the proper instructions sourced from a relevant appliance manual.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This variable speed pulley is compatible with the following outdoor appliance brands: MTD.

This flat washer is a genuine MTD part, sold individually. This flat washer can be used as a replacement part in lawn mowers, snowblowers, tillers, edgers, chainsaws, log splitters, and wood chippers. The purpose of a flat washer for one of these small engine outdoor appliances is to serve as a fastening component, spacing internal parts out to reduce friction.The flat washer in a small engine outdoor appliance is a small component that can easily be lost or misplaced, in which case it should be replaced as soon as the operator notices its absence. The flat washer can also be stripped away over time, in which case it should be removed and replaced by this genuine OEM replacement part.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This flat washer is compatible with the following outdoor appliance brands: MTD, Craftsman, Toro, Cub Cadet, Troy-Bilt, Yard Machines, Huskee, MasterCut, Yard Man, Turf King, Montgomery Wards, Husky, and Murray.

This extension spring attaches to the axle support bracket and the drive belt idler pulley on many types of lawn and garden equipment. It creates additional tension to the drive belt idler pulley. Sometimes the extension spring can be stretched out or may break, often caused through excess use. If this is the case, the spring will need to be replaced.If the spring is broken or no longer creates the appropriate amount of tension, replacement is required. It is an easy process that only requires a set of pliers. The pliers can be used to take the old spring off of the yard equipment before attaching the new extension spring. Make sure the equipment is on a stable surface and powered off when working with it. Remove the spark plug wire to prevent accidents.This extension spring is an authentic OEM replacement part sourced directly from the manufacturer. It is sold as an individual component. The spring is made to be used with lawnmowers, lawn tractors, and tillers created by MasterCut, Yard-Man, Bolens, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Cub Cadet, and Craftsman.

This flat washer is a genuine MTD part, sold individually. This flat washer can be used as a replacement part in lawnmowers, snowblowers, tillers, string trimmers, leaf blowers, edgers, log splitters, and wood chippers. The purpose of a flat washer for one of these small engine outdoor appliances is to prevent friction between one or more components while also creating spacing between components.The flat washer in a small engine outdoor appliance is a very small component that can be easily lost or misplaced at any point during its typical lifespan. The flat washer could also suffer damage during the course of general use, and if the damage to the flat washer precludes it from reducing friction and spacing one or more components, the flat washer should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This flat washer is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, Huskee, Montgomery Wards, Yard-Man, Turf King, and MasterCut.

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.

This is a genuine washer lock that is designed to be used in various applications on lawn and garden equipment. It is a standard piece of hardware that provides a strong seal and distributes pressure between the two connected components. Because of the exposure to high pressure and vibrations, these washers can become damaged or broken over time. If they are not replaced promptly, the connection between the two different parts may be affected. These washers are small and can also get lost while doing other repairs, so it may be helpful to keep some extras on hand. This genuine OEM lock washer is manufactured to exact standards and is compatible with several lawn and garden machines from Husky, Cub Cadet, MTD, RYOBI, Yard Machines, Troy Bilt, Yard Man, and Bolens. It can be used with over 150 models of tractors, blowers, cultivators, trimmers, and snowblowers. Consult the parts diagram for the exact location(s) and application(s) of this washer. Replacing this washer will require a screwdriver or socket set to attach the screws or bolts that the washer is securing. Always wear gloves for hand protection when replacing engine components like this lock washer.

This replacement part is a washer. This part is a genuine replacement part made by MTD. Washers are an important part of many different types of appliances. These small pieces work together with nuts and screws to help different parts of the machine stay in place and secure so that everything operates smoothly. A new washer might be needed if the current one is missing or damaged in any way. It is possible that washers can become stripped over time and might not stay in place. If this is the case it is recommended that it be replaced. This repair should be fairly easy and only require a screwdriver and possible pliers. Be sure to wear work gloves during this repair. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit and long-lasting use.

This replacement part is a washer. This is a genuine replacement part made by MTD. This specific washer is an important part of various machinery. These small pieces are responsible for working together with other small parts to help ensure the proper functioning of any machine. It also allows for parts to stay in secure during use. A new washer might be needed if the current one is visibly missing or damaged. Washers can become stripped over time and might not stay in place. If this is the case it is recommended that it be replaced. This repair should be easy and only require a screwdriver. Be sure the engine is completely powered down before attempting this repair. This part is sold individually and is sourced directly from the manufacturer. This washer is a genuine OEM replacement part.

This part is a replacement flange bearing. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. It is intended to replace a defective, worn, or broken flange bearing in various models of outdoor power equipment.Bearings reduce friction between moving parts and thus are essential to proper equipment functionality. Bearings may become worn, corroded, or ineffective over time and thus will need to be replaced with a genuine OEM replacement part. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to use this flanged bearing, the appropriate owner's manual and equipment diagrams should be referred to. This flange bearing is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with outdoor power equipment models that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands.

The variable speed belt goes around the engine pulley and the variable speed pulley. It is used on machines that have variable speed pulley drives and that need to be able to operate at different speeds. hese belts will wear down over time and need to be replaced. If the belt breaks, stretches too much or is worn down, replace it with a v-belt that fits properly. A screwdriver, pliers, socket set, and a wrench set will be needed to replace the belt. This is a genuine OEM part for lawn tractors, as well as other types of equipment with variable speeds, such as a snowblower, tiller, wood chipper, or log splitter. It is sold individually, and it will work on lawn tractors from many brands, including Ryobi, MTD, Craftsman, Yard Machines, Yard-Man, Turf King, and Mastercut.

This V-belt is a genuine MTD part, sold individually. This V-belt can be used as a replacement part in a lawn mower or a lawn tractor. The purpose of the V-belt in a lawn mower or lawn tractor is to facilitate the self-propelling feature of the appliance through rotation.The V-belt of a lawn mower or a lawn tractor might need to be replaced if the V-belt is worn out or damaged. If the V-belt is frayed, torn, ripped, scraped, dented, eroded, or warped to the point that it cannot rotate and drive the lawn mower, the V-belt should be removed and replaced by this genuine OEM replacement part. It is a simple replacement process that can be easily performed with only basic tools, in accordance with the proper instructions sourced from a relevant appliance manual.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This V-belt is compatible with the following outdoor appliance brands: MTD and Yard Machines.

This flat idler pulley is intended for use with some lawn tractor models. The idler pulley fits between the pulley and the variable speed pulley. It helps to ensure the tractor is operating efficiently by providing tension and guiding the drive belt in the engine. One of the common signs of a problematic idler pulley is a squealing sound when the engine is idling.The pulley could become damaged due to wear and tear over time. There is also a chance for corrosion, although this is rare except in machines that have had the same pulleys for many years. They will need to replace problematic pulleys to make sure their tractor runs properly. The owner can replace the pulley on their own using pliers, a screwdriver, and a wrench set.The flat idler pulley is for use with select lawn tractors from MTD, Ryobi, Yard Machines, Yard-Man, and Husky. The part is sold individually. It is a genuine OEM replacement part that has been sourced from the manufacturer.

This tubeless air valve attaches to wheels, allowing air into and out of the tires on various lawn equipment. Regularly replacing this part is considered a part of routine maintenance. Make sure that you use appropriate pliers and other tools for easy installation. Be sure to use gloves when replacing these valves and work with caution so as not to damage the sensitive parts. This OEM tubeless air valve can be the perfect fit for compatible wheels on equipment such as lawn mowers, snowblowers, tillers, edgers, log splitters, and wood chippers. It is designed for use with select models from MTD, including Craftsman, Troy-Bilt, Bolens, Remington, Yardman, RYOBI, Husky, Power Pro, and many others. There is a limited parts warranty on this valve, which is made of durable rubber and metal and designed to offer a high-quality replacement. Sold individually.

This is a self-tapping screw that can be used on a wide variety of lawn and garden equipment in many applications. A self-tapping screw is used to secure metal, wood, plastic, and brick together. When using a self-tapping screw, there's no need to drill a pilot hole since the screw makes its own hole. The only exception is with metal, which will still need a drilled hole before installation. There are many situations when a screw may need to be replaced. Some screws are damaged or broken, while others can become loose and no longer hold materials together. Screw heads can become stripped, which will also mean they need to be replaced. A visual inspection can often give an indication of whether you should replace a self-tapping screw. This is a genuine OEM hex head screw that can be used on various lawn and garden equipment, including wood chippers, lawn mowers, snowblowers, log splitters, tillers, edgers, and leaf blowers. It's compatible with products by MasterCut, Craftsman, Turf King, Cub Cadet, Yard-Man, Ryobi, Bolens, Troy-Bilt, Montgomery Wards, Murray, Huskee, Yard Machines, MTD, and more. This screw is sold individually.

This part is a hex cap screw that is used on a variety of outdoor power equipment. A hex cap screw is used to fasten components together securely. The head of the screw is shaped like a hexagon, hence the name "hex cap screw."A new hex cap screw may be needed if the current one is stripped, broken, or missing. Since screws are such a small component, it is important to place them in a safe place so that they are not lost. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This hex cap screw is a genuine Husqvarna part. It is sold individually. This particular hex cap screw is compatible with chippers, shredders, lawnmowers, lawn tractors, snowblowers, and vacuums that are manufactured by the following brands: Husqvarna, Craftsman, Bolens, Husky, Yard Machines, Yard-Man, MTD, and Troy-Bilt.

This screw is a genuine MTD part. A screw can be used as a replacement part in lawn mowers, snowblowers, tillers, chainsaws, log splitters, and wood chippers. The purpose of this genuine OEM part is to rotate and pierce into one or more components within the internal or external machinery of the appliance so that the stability of those components is maintained throughout general use of the appliance.The screw in an lawn equipment might need to be replaced if it has been lost, misplaced, or has suffered enough damage as to loosen the components that it is supposed to secure.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This screw is compatible with equipment manufactured by MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Murray, Yard Machines, Huskee, Montgomery Wards, Yard Man, Turf King, and MasterCut.

This is a ferrule from MTD. This particular ferrule is designed for use in the lawn mower's driveshaft. The wire rope (or tension spring) is attached to the variable speed pulley and engages the driveshaft/transmission system.A faulty ferrule on a lawn mower may cause the wire rope to snap or become disconnected from the driveshaft. The rope doesn't necessarily have to break to signal a malfunctioning ferrule. The rope may lose torque and cannot provide the tension needed to make adjustments to the driveshaft. In simpler terms, the lawn mower may lose its ability to shift between different speeds.The ferrule is located near the variable speed pulley (drive pulley) of the lawn mower. The deck will need to be removed to make any repairs to the ferrule. The belts will need to be removed also. Always make sure the brake is engaged before starting any repairs on this section of the lawn mower. This part is compatible with Craftsmen, TroyBilt, and MTD lawn mowers.

Cotter pins are simple but very effective fasteners used primarily to hold wheels in place on mowers. This is particularly true of the front wheels on riding mowers. Cotter pins are very light and can become overly pliable after extensive use. In some cases, the front wheels of a mower, which are the guide wheels that steer the device, become difficult to manage. The cure for this situation is often simply the replacement of the cotter pins that are not holding the guide wheels adequately in place. Before attempting to remove the pins, it is essential that the spark plug boot is moved so that the mower cannot be started. This is an important safety step because the repairer will be getting under the mower near the blades. The back wheels should be blocked so the mower cannot move, then the front end placed up on blocks. Remove the mower's hubcaps to gain access to the axle spindles. Straighten the legs of the pin so that when the curved portion of the cotter pin is grasped with pliers and it can be pulled straight back and be removed. The spindle, washers, and wheels should be checked for wear before the new pin is placed and secured. This OEM cotter pin is compatible with Bolens, Yard-Man, Craftsman, Yard Machines, Cub Cadet, Turf King, Troy-Bilt, Huskee, Toro, Ryobi, MTD, MasterCut, Murray, and Montgomery Wards.

This square key is a genuine MTD part, sold individually. This square key can be used as a replacement part in lawnmowers, snowblowers, tillers, leaf blowers, edgers, log splitters, and wood chippers. The purpose of the square key for one of these small engine outdoor appliances is to fit tightly into the gears, cams, sprockets, and pulleys within the general internal machinery of the appliances to keep the parts affixed to the shaft.The square key in a small engine outdoor appliance might have to be replaced if the square key is lost or misplaced, as it is a small component that can easily go missing without announcing its absence. The square key can also be damaged from general wear and tear over long-term use, meriting its replacement by this genuine OEM replacement part.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This square key is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Yard Machines, Huskee, Montgomery Wards, Yard-Man, Turf King, and MasterCut.

The cotter pin is a fastener that is commonly used in lawn and garden equipment. The cotter pin helps provide a secure, locking fit that is adjustable and easy to remove. The cotter pin is commonly used on axles and rods, but it can have many applications depending on the machine and model. Cotter pins can become worn or break down over time because they are exposed to constant vibrations. It is important to replace damaged or broken cotter pins immediately as a broken part can render the equipment useless in many cases. This cotter pin is designed to exact OEM standards by MTD, and is designed for use in various equipment from MTD, Troy-Bilt, Craftsman, RYOBI, Yard Machines, Hard Man, Poulan, Husky, Bolens, and Cub Cadet. This is a 5/16 cotter pin that features a #34 diameter, and is made of a durable metal. This part is sold individually and those who require more than one will have to order multiple quantities. No other hardware is included. Always wear gloves when working on lawn and garden equipment.

This OEM part is a cotter pin for lawnmowers. The cotter pin is the small clip that secures the mower deck to the mower. A cotter pin can become rusted or damaged due to exposure to the elements. If the cotter pin is no longer securing the mower deck, then it will need to be replaced. Luckily replacing this part is a relatively simple fix.To replace the cotter pin, start by making sure the mower is turned off. After that, locate the old damaged pin. Use a pair of pliers to pull it out of its place. Once removed, slide the new pin into its opening and make sure it is set securely on the mower deck. Once secured, turn the mower on to see if the pin can hold the mower deck.This genuine replacement part is sold individually and is compatible with MTD brand mowers.

The hex screw is a specialty screw that has various uses on lawn and garden equipment engines and housings. Over time, screws are known to become worn, corroded, lost, or otherwise damaged. This is an identical replacement that will have many locations and applications, but when it becomes damaged or gets lost it should be replaced as soon as possible. This is a specialty screw that is not designed for general use. Refer to parts diagrams for the appropriate location and installation of this screw for a guaranteed fit. This OEM hex screw is manufactured to exact standards and can be used in more than 150 different brands of machines. It is compatible with snow throwers, lawn mowers, and blowers from RYOBI, Yard Machines, Yard Man, Poulan, Troy-Bilt, MTD, Bolens, Cub Cadet, and Husky. This high-quality hex screw is made of metal and sold as an individual unit. Those who need more than one screw will have to purchase multiple quantities. A wrench is required to replace this screw. Always allow engines to cool completely before performing any repairs and wear gloves for hand protection.

This bell washer is a genuine MTD part, sold individually. This bell washer can be used as a replacement part for a lawn tractor, chipper shredder, tiller, or lawnmower. This bell washer adds spacing on a shaft in the tool.If the user of the appliance notices that a washer is missing, it should be replaced. General wear and tear is very normal for outdoor appliances, and if it occurs, the washer should be removed and replaced with this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bell washer is compatible with the following outdoor appliance brands: MTD, Yard Man, Yard Machines, and Troy-Bilt.

A hex screw fastens and holds two components together. It has a hexagonal head and features threading starting underneath the shoulder down to the tip. Its all-metal construction offers rigidity and longer lifespan. It is also threaded, so you can conveniently loosen or tighten in position. It measures 1/4-20 x 0.5 inch and comes in brass or gold color. Take note that this replacement hex screw may beused in different locations of a machine. Double check the device’s model number for compatibility. To install this hex screw, you will need a hex wrench or a hex socket. This hex screw is a replacement made by MTD. This screw/bolt may be used on lawn mowers, snowblowers, tillers, string trimmers, leaf blowers, edgers, chainsaws, pole pruners, log splitters, or wood chippers made by Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, or MasterCut. This OEM hex screw is sold individually.

This replacement part is a hex screw, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This screw can be used in a variety of ways depending on the repair needed. Hex screws are similar to normal screws except they have a six-sided head, like a hexagon. A new hex screw might be needed if the current one is damaged or missing. It is common that screws may become stripped or loose overtime, causing them to fall out. If any parts of the lawn mower are becoming loose or falling off, the hex screw might be missing. This replacement should be fairly easy and should only require a screwdriver and possibly pliers. This part is a genuine OEM replacement part and is sold individually. Be sure to purchase the correct amount as some appliances require more than one hex screw.

This is a flat washer with an inner diameter of .469 inches. The washer is a replacement part that is for use with types of lawn and garden equipment. Flat washers help to increase the size of a screw's bearing surface area. It will help to reduce the surface pressure that is applied when the pieces are fastened together, and it will help to protect the pieces being connected.The flat washer is made from metal, which means it is durable. However, even metal can start to wear away over time. It could become thinner, corrode, or even become cracked. When this happens, owners will need to replace the washer. In some cases, the washers might become lost when working on the machine. Getting a new washer to replace any that are missing is essential.The flat washer will work with a range of select machines including tillers, lawn tractors, snowblowers, cultivators, and mowers from Yard-Man, Troy-Bilt, Ryobi, MTD, Bolens, Yard Machines, Husky, and Cub Cadet. The washer is sold individually and is a genuine OEM replacement part.

This insulator nut plate is a genuine MTD part, sold individually. This insulator nut plate can be used as a replacement part in a lawn mower. The purpose of the insulator nut plate in a lawn mower is to self-wrench into a bolt as a fastening component of several parts within the machinery of the appliance.The insulator nut plate can be easily lost or misplaced, or the component can become damaged and stripped over time from general wear and tear or as the result of an accident. The insulator nut plate is a small component and if it is found to be missing, it should be replaced by this genuine OEM replacement part. If the insulator nut plate is damaged, it should also be replaced. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This insulator nut plate is compatible with the following outdoor appliance brands: MTD, Craftsman, Toro, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Huskee, Bolens, Yard Man, and MasterCut.

The exhaust systems on lawn and garden equipment are just as important as those on a vehicle. They need a good seal to prevent a leak between the carburetor and the exhaust tube, which would allow air leakage that could cause performance issues and loud noise. Over time all exhaust gaskets deteriorate and require a full replacement. It is relatively easy to replace an exhaust gasket and requires only the use of screw drivers, a socket set or a wrench set depending on the device being service. Replacement components such as sockets or screws may also be required during this repair. The gasket surfaces should be cleaned and fully dried before being installed between the carburetor and the exhaust tube. This exhaust gasket works with Toro, Simplicity, Murray and Briggs & Stratton lawnmowers, generators, snowblowers, wood chippers, and lawn tractors. It also works with equipment made by Craftsman, Husqvarna, Cub Cadet, Poulan, Wheel Horse, MTD, Ariens, and more.