Parts for Ge ZIS480NMD: 01 - Freezer Door Parts

The water filter is an OEM part for GE refrigerators. This filter removes or reduces various contaminants.

Features and Benefits:

• Easy DIY replacement, typically mounted inside the refrigerator at the back of the compartment.
• Removes or reduces various contaminants in your water and ice, including lead, cysts, asbestos, atrazine, , taste and odor, chlorine, sediment, turbidity, and more
• NSF/ANSI 42 and 53 standards
• 6 Month lifespan filter
• Carbon Block media
• Micron rating: 0.5-1 micron (Class I)

When to replace your filter:

• Bad taste or odor in water and ice
• Cloudy or discolored ice
• Reduced water flow or pressure
• Refrigerator replace filter indicator light is on

Note: If replacing the Culligan metal canister design filter for the first time, a special adapter, part number AP2615702 is needed, which is not included with this part. The compatible bypass cap is part number AP6891551.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This hardware pack provides the assorted fasteners needed to secure trim, panels, and small appliance components, helping replace missing or damaged screws and clips for a clean, stable fit. What it does

• Replaces lost or damaged screws, clips and small fasteners used on appliance trim and panels
• Helps stop rattling or loose panels by restoring proper fastening
• Secures small components during reassembly after maintenance or part replacement
• Useful when original mounting hardware is missing or corroded

• Disconnect power to the appliance before servicing to reduce shock risk
• Use the correct screwdriver or driver bit to avoid stripping fasteners
• Keep small parts away from children and pets; work on a covered surface to catch dropped pieces

This bottom freezer door hinge secures and guides the freezer door at the lower pivot, restoring proper door alignment and sealing for consistent cooling. Designed to replace a worn, bent or broken lower hinge. What it does:

• Provides a stable pivot point so the freezer door opens and closes smoothly
• Helps maintain an even door gap to improve seal and reduce cold air loss
• Prevents sagging or misalignment that can cause rubbing or difficulty latching
• Fits the lower/bottom position on compatible freezer doors

• Inspect hinge mounting holes and fasteners; replace any damaged screws or clips
• Support the door during removal/installation to avoid strain or injury
• Tighten fasteners snugly but avoid over-torquing to prevent damage
• If door continues to sag after replacement, check upper hinge and door gasket condition

This replacement freezer bottom hinge bushing helps the freezer door pivot smoothly and maintain proper alignment, reducing rubbing and uneven wear for more reliable closing. What it does:

• Provides a smooth pivot surface for the freezer bottom hinge
• Restores proper door alignment to help ensure a tight seal
• Reduces hinge noise, sticking, and rubbing during door movement
• Helps prevent premature wear of the hinge and door components

• One freezer bottom hinge bushing

• Disconnect power to the appliance and empty or support the door before starting
• Support the door while removing hinge fasteners to prevent falling or injury
• Inspect the hinge and shaft for wear; replace the hinge assembly if damaged
• Do not overtighten fasteners; test door operation after installation

This refrigerator door gasket creates an airtight seal between the door and cabinet to keep cold air in and moisture out. Replace a torn, warped, or leaky gasket to restore proper sealing and consistent temperatures around the door opening. What it does:

• Seals the door perimeter against the cabinet to limit air leaks
• Helps maintain interior temperature and reduce condensation or frost near the door
• Supports proper door closing and alignment
• Common symptoms of a failed gasket: visible cracks/tears, door not sealing, condensation or frost at the door edge, warm spots near the door

• One door gasket

• Disconnect power before servicing
• Warm the new gasket (soak in warm water or use low heat) to make it pliable
• Remove the old gasket and clean the retainer/channel thoroughly
• Press the new gasket fully into the retainer; square corners, check for even contact all around, and use gentle low heat to relax waves; allow up to 24 hours for the gasket to conform

This bin door assembly is the flip-up cover for a small door bin compartment on your refrigerator. Replacing a cracked or missing cover keeps items contained and restores convenient access and a clean, finished look. What it does:

• Covers the door bin compartment and flips up for easy access
• Helps keep items from falling out when the door opens and closes
• Restores proper function when the original cover is cracked, warped, or missing
• Typical symptoms include broken hinge tabs, a cover that won't stay closed, or a loose/misaligned lid

• Includes 1 bin door assembly

• Remove items from the affected bin
• Release the old cover from the hinge tabs or pins and lift it off
• Align the new cover's tabs with the bin hinges and press/snap into place
• Do not force parts; verify smooth open/close after installation

This pack contains twelve replacement screws used to fasten appliance panels, trim, and components. They restore secure mounting and help stop rattling, loose panels, and gaps for a safer, quieter appliance. What it does:

• Secures exterior and interior panels, brackets, and trim pieces
• Restores proper fit where missing or stripped screws cause movement or noise
• Helps maintain appliance alignment and prevents parts from vibrating loose
• Used for general-purpose repairs on compatible GE appliances

• Disconnect power or unplug the appliance before performing any internal repairs
• Use the correct screwdriver bit and avoid overtightening to prevent stripping threads
• Keep remaining screws in a labeled container for future service
• If a screw does not seat easily, stop and verify correct fit to avoid damage

Replacement screw that secures panels and internal components, helping stop rattles and keep parts aligned. Use it to replace stripped, rusted, or missing fasteners and restore a secure fit. What it does:

• Secures panels, trim, or internal parts to prevent movement and vibration.
• Replaces worn, corroded, or missing screws that cause loose panels or rattling.
• Restores proper alignment for doors, covers, and mounted components.
• Provides a simple hardware fix that helps maintain safe, stable operation.

• Always disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head; apply firm but controlled torque.
• Verify screw length, head style, and thread type match the original before installation.
• If threads are damaged, replace with a matching OEM screw rather than over-tightening.