Parts for Ge ZISB480DNBII: Freezer Door Parts

This is a #8-18 x 5/8 inch oval-head stainless steel screw used to secure panels and components on compatible GE appliances. It replaces missing or damaged fasteners to restore a secure fit and reduce vibration or rattling. What it does

• Secures trim, access panels, brackets or small components in place
• Restores proper alignment when a lost or stripped screw causes loose parts
• Helps eliminate rattling, vibration, or intermittent contact caused by missing fasteners
• Corrosion-resistant stainless finish for longer life in appliance environments

• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage or cracking nearby plastic
• Power tools can be used carefully on low torque settings
• Replace any stripped mating nuts or threaded inserts for secure fastening

This replacement freezer bottom hinge bushing helps the freezer door pivot smoothly and maintain proper alignment, reducing rubbing and uneven wear for more reliable closing. What it does:

• Provides a smooth pivot surface for the freezer bottom hinge
• Restores proper door alignment to help ensure a tight seal
• Reduces hinge noise, sticking, and rubbing during door movement
• Helps prevent premature wear of the hinge and door components

• One freezer bottom hinge bushing

• Disconnect power to the appliance and empty or support the door before starting
• Support the door while removing hinge fasteners to prevent falling or injury
• Inspect the hinge and shaft for wear; replace the hinge assembly if damaged
• Do not overtighten fasteners; test door operation after installation

This gasket and label assembly is used on side-by-side refrigerators to restore a proper seal at the specified location and provide the matching identification decal. A tight seal helps keep cold air in, moisture out, and performance consistent.

• Creates an air-tight seal between mating refrigerator parts or panels
• Helps maintain stable temperatures and reduce frost/condensation
• Replace if the gasket is torn, deformed, brittle, or missing
• Helps address sweating around edges, warm spots, or longer run times

• Disconnect power before servicing; turn off water supply if working near water components
• Remove the old gasket/label and clean/dry the surfaces thoroughly
• Seat the gasket evenly without twists; ensure full contact all around
• Apply the label in the specified location per your model's documentation

This bin door assembly is the flip-up cover for a small door bin compartment on your refrigerator. Replacing a cracked or missing cover keeps items contained and restores convenient access and a clean, finished look. What it does:

• Covers the door bin compartment and flips up for easy access
• Helps keep items from falling out when the door opens and closes
• Restores proper function when the original cover is cracked, warped, or missing
• Typical symptoms include broken hinge tabs, a cover that won't stay closed, or a loose/misaligned lid

• Includes 1 bin door assembly

• Remove items from the affected bin
• Release the old cover from the hinge tabs or pins and lift it off
• Align the new cover's tabs with the bin hinges and press/snap into place
• Do not force parts; verify smooth open/close after installation

This top freezer door trim replaces the upper decorative and protective trim on the freezer door, restoring a finished look and helping seal and align the door edge. It's a direct-fit exterior trim piece for compatible models. What it does:

• Covers and protects the top edge of the freezer door while providing a finished appearance
• Helps maintain proper door alignment and sealing where the trim interfaces with the door
• Replaces faded, scratched, or damaged trim that can affect door fit and aesthetics
• Matches original OEM fit and mounting points for a clean repair

• One top freezer door trim piece

• Installation requires removing the freezer door trim screws or clips; keep hardware for reassembly
• Use a soft cloth to avoid scratching the trim during installation
• Disconnect power only if removal requires tilting or taking the door off to avoid injury

This handle trim cover replaces a worn or damaged door handle end cap to restore a clean, finished look and hide fasteners. It snaps or slides into place on the door handle for a neat appearance. What it does:

• Covers the exposed end of a refrigerator/freezer door handle for a finished appearance
• Hides screws and fasteners to improve aesthetics
• Helps keep dirt and moisture out of the handle cavity
• Suitable when trim is cracked, scratched, faded, or missing

• 1 handle trim cover

• Remove the existing trim or handle before installing
• Align trim with handle end and press or slide into place until it seats securely
• Use basic hand tools; avoid forcing parts to prevent damage
• Disconnect power or follow appliance safety guidance before servicing if applicable