Parts for Frigidaire GRMC2273CD00: Freezer & Middle Drawer|Fdgrmc2273bf.Svg Parts

This refrigerator door gasket creates a tight seal around the door opening to keep cold air in, reduce frost, and maintain stable temperatures. Replace a worn seal to stop air leaks and restore cooling performance and efficiency.

• Seals the perimeter of the refrigerator or freezer door to prevent warm air infiltration
• Helps maintain set temperatures and humidity; reduces frost and condensation near the door
• A damaged seal can lead to longer run times or the door not staying closed
• Common signs: tears, cracks, warping, visible gaps, frost along the gasket, moisture on the frame

• Disconnect power before servicing; open the door and remove the old gasket from its retainer
• Allow the new gasket to relax at room temperature; warming it in warm water helps remove kinks
• Clean the door channel; start corners first, then press the gasket fully into the retainer all around
• Close the door and check for uniform contact; adjust hinges/leveling as needed. Use gentle, low heat only to smooth waves

This door gasket seals the refrigerator door to keep cold air in and warm air out, helping maintain proper temperatures and reduce energy use. It replaces a worn or torn seal to restore appliance performance. What it does:

• Creates an airtight seal around the refrigerator door to prevent cold air loss
• Helps stop frost buildup and reduces condensation inside the compartment
• Reduces compressor run time and energy waste caused by a failing seal
• Commonly replaced when the seal is cracked, torn, flattened, or no longer seals

• Always disconnect power to the appliance before starting any repair
• Clean the door channel and remove old adhesive or debris before installing the new gasket
• Press the gasket into the channel evenly; start at one corner and work around the door for a consistent seal
• If needed, warm the gasket slightly to make it more pliable for installation; avoid using open flames or excessive heat

This door gasket seals the refrigerator door to keep cold air in and warm air out, helping maintain proper temperatures and reduce energy use. It replaces a worn or torn seal to restore appliance performance. What it does:

• Creates an airtight seal around the refrigerator door to prevent cold air loss
• Helps stop frost buildup and reduces condensation inside the compartment
• Reduces compressor run time and energy waste caused by a failing seal
• Commonly replaced when the seal is cracked, torn, flattened, or no longer seals

• Always disconnect power to the appliance before starting any repair
• Clean the door channel and remove old adhesive or debris before installing the new gasket
• Press the gasket into the channel evenly; start at one corner and work around the door for a consistent seal
• If needed, warm the gasket slightly to make it more pliable for installation; avoid using open flames or excessive heat

This door gasket seals the refrigerator door to keep cold air in and warm air out, helping maintain proper temperatures and reduce energy use. It replaces a worn or torn seal to restore appliance performance. What it does:

• Creates an airtight seal around the refrigerator door to prevent cold air loss
• Helps stop frost buildup and reduces condensation inside the compartment
• Reduces compressor run time and energy waste caused by a failing seal
• Commonly replaced when the seal is cracked, torn, flattened, or no longer seals

• Always disconnect power to the appliance before starting any repair
• Clean the door channel and remove old adhesive or debris before installing the new gasket
• Press the gasket into the channel evenly; start at one corner and work around the door for a consistent seal
• If needed, warm the gasket slightly to make it more pliable for installation; avoid using open flames or excessive heat

Replacement door magnet that helps the refrigerator or freezer door stay closed for a tighter seal and more consistent cooling. Restores magnetic hold so doors close reliably and reduce warm spots. What it does

• Provides magnetic hold for the door liner so the door stays shut during normal use
• Helps maintain the gasket engagement to preserve internal temperature
• Common symptom: door not staying closed, food warming, or frost build-up near the door
• Used in door/gasket assembly where magnets secure the seal

• Turn off power to the appliance or unplug before removing door trim or accessing internal components
• Remove door liner or gasket per service instructions to access and replace the magnet; keep fasteners and seals intact
• Press or seat magnet into its channel or mounting location; use the OEM fastener or adhesive method specified by the manufacturer

This outer door assembly replaces a damaged or worn exterior oven door panel to restore appearance and provide a proper seal. It ships as a finished stainless exterior door ready for reuse with existing inner components. What it does

• Replaces a dented, scratched, or corroded outer door to restore the oven's exterior finish
• Helps maintain a proper outer barrier for heat containment when used with existing inner door parts
• Addresses cosmetic issues and visible wear on the appliance front
• Compatible with factory door mounting points and trim when original inner parts and hardware remain installed

• High-level replacement only: outer door swaps typically require removing the door from the appliance and separating outer and inner panels—follow the model-specific service manual.
• Handle and trim may need transfer from the old door; confirm what ships before installation.
• Wear appropriate PPE (gloves, safety glasses) and avoid scratching the finished surface during handling.
• Disconnect power at the breaker and allow the appliance to cool before starting work.

This outer door assembly replaces a damaged or worn stainless exterior door on compatible refrigerators to restore appearance and a proper seal. It provides the finished exterior panel and mounting points for the door trim and hardware. What it does:

• Replaces dented, scratched, or corroded outer door panels to improve cosmetic appearance
• Restores correct mounting surfaces for hinges, handles and trim pieces
• Helps ensure proper door alignment and sealing when installed correctly
• Prevents further damage to internal door components by providing a protective outer shell

• Disconnect power to the appliance and remove any food before starting
• Door assemblies can be heavy and awkward — get a helper to support the door during removal and installation
• Keep hardware and inner door components organized; some factory fasteners and gaskets may be reused
• Inspect hinges and seals during installation and adjust door alignment for an even gap and proper closing

This interior refrigerator lamp replaces a burned or dim light to restore usable illumination inside the appliance, making it easier to find items and temperatures at a glance. Simple swap restores safe, visible interior lighting. What it does:

• Replaces a failed or flickering refrigerator interior lamp so the compartment is properly lit
• Helps you see food clearly to prevent spoilage and make loading/unloading easier
• Restores normal operation when the lamp no longer lights or is visibly damaged
• Works with compatible Frigidaire refrigerator light housings and sockets

• One interior refrigerator lamp

• Disconnect power before servicing to avoid electrical shock
• Handle the lamp carefully; avoid touching glass with bare hands if it's a halogen-style bulb
• Seat the lamp securely in the socket and restore power to test operation
• If the lamp still doesn't work after replacement, check the socket and door switch for issues

This electronic control board governs the oven's functions and display. Replacing a failed EOC can restore accurate temperature control, cycle selection, and clock/timer operation so your range or wall oven runs the way it should.

• Controls bake/broil relays to reach and maintain set temperatures; failures may cause no heat, slow preheat, or erratic cycling
• Powers the clock, display, and keypad; symptoms include a blank display, beeping, or unresponsive buttons
• Coordinates modes such as preheat, timed bake, and self-clean on applicable models; recurring F-code errors can point to a faulty board
• Monitors sensors and safety inputs; faults may prevent cycles from starting or may end them prematurely

• Disconnect power at the breaker before servicing; verify no voltage is present
• Handle the board by the edges and use anti-static precautions
• Photograph wiring and move connectors one at a time to the new board; secure all mounts
• Some models require configuration/programming after install; follow the tech sheet for your appliance

This replacement screw secures appliance panels, brackets, and components for a solid, rattle-free fit. Replace stripped, rusted, or missing hardware to restore proper alignment and dependable fastening where this fastener is specified.

• Fastens panels, brackets, trim, or internal parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling noises
• Direct replacement for stripped, rusted, or missing hardware
• Symptoms include loose panels, gaps, or screws that won't tighten

• Disconnect power (and gas/water if applicable) before servicing
• Use the correct driver/bit; hand-start threads to avoid cross-threading
• Replace screws one at a time to maintain alignment
• Snug firmly—do not overtighten into plastic or thin metal

This replacement cover protects internal components and finishes the appliance's exterior for a clean, secure appearance. It restores a missing or damaged panel so the appliance can operate safely and look complete. What it does

• Covers and protects control or internal components from dust, debris, and accidental contact
• Prevents rattling and keeps internal parts secured behind the panel
• Restores a finished appearance when the original cover is cracked, broken, or missing
• Helps maintain safe operation by shielding wiring and connectors from exposure

• Disconnect power to the appliance before beginning any work
• Remove mounting screws or clips from the old cover and reuse existing hardware
• Align the cover, then secure with the original screws or clips; do not overtighten to avoid cracking
• If mounting hardware is missing or damaged, obtain replacement fasteners that match the appliance specifications

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This replacement refrigerator drawer provides a durable storage bin to keep foods organized and contained inside the cabinet. It restores smooth sliding and usable storage when an original drawer is cracked, warped or missing. What it does:

• Holds and organizes fresh or frozen food items in the refrigerator compartment
• Replaces damaged, cracked or broken drawers that no longer seal or slide correctly
• Restores proper containment to prevent spills and keep items from shifting
• Helps recover full usable storage space in the fridge or freezer section

• One replacement drawer

• Remove power or unplug the appliance before starting any repairs
• Slide out the old drawer and lift to disengage from tracks; align new drawer on tracks and slide into place
• Handle with care to avoid chipping or cracking the new plastic; wear gloves to protect hands
• If drawer does not seat or slide smoothly, inspect and clean tracks and rollers before forcing installation

This is a replacement mounting screw used to secure appliance panels and small components so parts stay firmly in place during normal use. Installing the correct screw restores proper fit and reduces rattles or loose trim. What it does:

• Fastens panels, brackets, or trim to the appliance frame
• Keeps components aligned to prevent vibration and noise
• Replaces a lost or stripped screw to restore secure attachment
• Helps maintain safe, stable operation by holding parts where they belong

• One replacement mounting screw

• Disconnect power and water before servicing
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can damage threads or panels
• Keep removed fasteners organized so you reinstall them in the original locations

This replacement refrigerator drawer restores a missing, cracked or damaged storage bin so you can keep produce and deli items organized. Durable molded plastic design fits the original cavity and slides into the existing tracks. What it does:

• Replaces a broken, cracked or missing refrigerator storage drawer to restore usable bin space
• Holds produce, deli items or packaged foods and helps keep contents contained
• Slides into existing drawer tracks; restores proper drawer fit and alignment
• Common symptom fix: drawer falls out, won't close fully, is cracked or won't hold items

• Remove all food and empty the compartment before installing
• Slide drawer into the cabinet tracks until it seats; ensure rails align and glide smoothly
• If tracks or rollers are damaged, replace them separately — this part is the drawer only
• Always follow manufacturer safety guidance; unplug power only if accessing electrical components

This basket assembly is the replacement storage basket that holds and organizes items inside the appliance, restoring secure support and proper circulation. It helps keep contents contained and prevents shifting or damage from a cracked or broken basket. What it does:

• Replaces a cracked, broken or worn basket that no longer supports items
• Restores proper storage and prevents items from shifting or falling
• Helps maintain airflow/clearance where applicable so the appliance can operate as intended
• Fits into the existing cabinet/drawer framework and works with original mounting points

• One complete basket assembly as shown

• Installer should unplug or disconnect power and/or shut off water supply before servicing appliance
• Remove the old basket by reversing factory mounting steps; inspect surrounding rails and clips for wear
• Reuse original fasteners if undamaged; replace any broken mounts for a secure fit

This replacement slider is the small plastic guide that helps a drawer, bin or tray move smoothly along its track so the compartment opens and closes reliably. It restores proper alignment and reduces scraping or sticking. What it does:

• Guides and supports a drawer/bin/tray along its track for smooth movement
• Helps restore proper alignment so the compartment closes evenly
• Reduces scraping, binding, and noisy operation during use
• Prevents excess wear on the track and adjacent components

• One replacement slider

• Remove power and empty the drawer/bin before replacing the slider
• Most sliders snap or slide into a track; align and press until it clicks into place
• Inspect the mating track for cracks or debris and clean before installation

This slider is a replacement drawer guide that restores smooth, stable sliding for a refrigerator or freezer drawer. It helps the drawer track properly so contents open and close without sticking or binding. What it does:

• Guides the drawer along its track so it slides in and out smoothly
• Keeps the drawer aligned to prevent tipping or catching on the cabinet
• Replaces a worn, cracked, or missing slider that causes scraping or uneven movement
• Reduces noise from dragging or rubbing during opening and closing

• One slider

• Disconnect power to the appliance before starting any repair
• Remove the affected drawer or bin to access the slider; note orientation for reassembly
• Slide or snap the new slider into the existing track; some sliders secure with a small screw or tab
• Test the drawer movement after installation and re-seat any retaining clips as needed