Parts for Ge FCM7CJBCD: Freezer Parts

This refrigerator door seal creates an airtight seal around the refrigerator door to help keep cold air in and warm, moist air out. Replacing a worn seal improves cooling efficiency and helps prevent frost and leaks. What it does:

• Seals the door to maintain proper internal temperature and energy efficiency
• Helps prevent condensation, frost buildup, and water leaks around the door
• Reduces compressor runtime by keeping cold air inside
• Restores a tight door fit when the old seal is cracked, torn, or deformed

• Inspect door flange for damage and clean mounting surface before installing the new gasket
• Warm the gasket gently if needed to help form to the door; avoid open flames or excessive heat
• Check door alignment and hinge condition; adjust if the door does not close evenly
• Disconnect power if required by your model before performing work; follow all safety precautions

This inner tube cover fits inside the washer tub to protect the tub opening and help keep clothes from catching on the basket edge. It provides a cleaner seal and reduces wear at the tub rim. What it does

• Covers and protects the exposed edge of the inner tub to prevent fabric snags and catches
• Helps maintain a sealed opening between the tub and basket area
• Reduces movement noise by keeping the tub edge covered
• Common replacement for visible wear, cracking, or if clothes repeatedly catch on the tub lip

• One inner tube cover

• Disconnect power (and water, if applicable) before starting any repair
• Access typically requires removing the washer basket or outer tub trim; keep fasteners organized
• Inspect adjacent seals and clips; replace any damaged fasteners for a secure fit

This drain tube cap seals the refrigerator defrost drain opening to help direct meltwater into the drain system and keep debris and odors out. A simple replacement that restores proper drainage and reduces leaks or pooling. What it does:

• Seals the defrost/drain tube opening to prevent water from escaping into the cabinet
• Helps keep food particles and debris out of the drain to reduce clogs
• Directs meltwater into the drain channel for normal defrost drainage
• Can reduce odors by blocking air flow through a compromised drain opening

• Disconnect power to the appliance before servicing.
• If the drain area is frozen, defrost and clear obstructions before installing the cap.
• Remove the old cap and press the new cap firmly into the drain tube until seated; do not force with excessive tools.
• After installation, test by pouring a small amount of water into the drain area to ensure proper fit and flow.

The Thermostat is an OEM part for GE chest freezers. The key electronic component monitors and regulates subzero holding temperatures inside the freezer. Consistent frozen storage relies on an accurate thermostat reading.

Causes of failure can include wear and tear on microswitch buttons from repeated use over the years, moisture corrosion breaking circuit pathways, and loose wire terminals preventing communication with other control boards.   

Symptoms of a faulty thermostat are:

• Fluctuating temperatures that do not match the dial setting    
• Strange odors or sounds coming from inside the cabinet
• Frozen items beginning to thaw or defrost

Replacing with this genuine GE thermostat ensures steady below-zero preservation. Compatible with Hotpoint, RCA, and Kenmore chest freezers, it also supports reliable frozen food protection.
 

This rubber grommet cushions and protects components where a snug, vibration-resistant fit is needed. It helps keep panels, wires or small parts seated and prevents chafing or rattling for quieter, safer operation. What it does:

• Provides a soft, vibration-damping mount to reduce noise from loose panels or components
• Cushions and isolates parts from metal-to-metal contact
• Protects wires and hoses from abrasion where they pass through openings
• Helps hold fittings, clips or small assemblies securely in place

• Disconnect power to the appliance before accessing internal parts.
• Access the panel or opening and remove the old grommet before installing the new one.
• Press the grommet into the hole until fully seated; avoid cutting or stretching it excessively.
• Use caution with sharp tools and fasteners to prevent injury or damage to surrounding components.

This bushing provides a low-friction bearing surface to support and align a rotating shaft or pivot, helping restore smooth, quiet operation and reduce wear on mating parts. What it does:

• Supports and centers a rotating shaft or pivot to maintain proper alignment.
• Reduces friction and wear between moving parts for smoother operation.
• Helps eliminate grinding, binding, or wobbling caused by worn bearings.
• Prevents premature wear of shafts and housings by providing a replaceable wearing surface.

• Disconnect power to the appliance before beginning any repair.
• Inspect surrounding housing and shaft for wear; replace damaged parts as needed.
• Press or tap the bushing into place squarely; avoid deforming the part.
• Ensure correct orientation and full seat for proper function.