Parts for Ge ZISB48DCA: 02 - Fresh Food Door Parts

This .030-inch shim is a thin leveling spacer used to correct small height and alignment gaps. It helps stabilize and align appliance components for proper fit and reduced vibration during operation. What it does:

• Provides a precise 0.030-inch thickness to raise or level panels, doors, or chassis components
• Helps eliminate small gaps that can cause rubbing, misalignment, or uneven sealing
• Reduces vibration or rocking by evening out contact points and load distribution
• Useful during cabinet installation or when replacing worn leveling feet or brackets

• Disconnect power (and water if applicable) to the appliance before performing service
• Use appropriate hand tools and keep shims flat and properly seated under the component being adjusted
• Add shims incrementally—do not force parts into position or over-tighten fasteners after shimming

Restore a tight, energy-saving seal on your refrigerator. This magnetized fresh-food door gasket keeps cold air in and warm air out, helping maintain temperature, reduce frost and moisture, and prevent the compressor from overworking.

• Seals the refrigerator compartment door to the cabinet
• Helps maintain stable temperatures and humidity
• Can reduce condensation, frost buildup, and energy loss from air leaks
• Worn or torn gasket may cause doors not to seal, warm spots, or excess run time

• Unplug appliance before service; wear cut-resistant gloves
• Soften gasket in warm water or with a hair dryer on low to ease installation
• Remove retaining screws or pull from retainer (design varies), then seat new gasket fully in the groove
• Check for uniform contact all around; adjust door hinges/leveling if needed

This pack contains twelve replacement screws used to fasten appliance panels, trim, and components. They restore secure mounting and help stop rattling, loose panels, and gaps for a safer, quieter appliance. What it does:

• Secures exterior and interior panels, brackets, and trim pieces
• Restores proper fit where missing or stripped screws cause movement or noise
• Helps maintain appliance alignment and prevents parts from vibrating loose
• Used for general-purpose repairs on compatible GE appliances

• Disconnect power or unplug the appliance before performing any internal repairs
• Use the correct screwdriver bit and avoid overtightening to prevent stripping threads
• Keep remaining screws in a labeled container for future service
• If a screw does not seat easily, stop and verify correct fit to avoid damage

Fresh food side door trim.

This is the fresh food side top door hinge. For bottom door hinge use WR13X766.

Fresh food side bottom hinge shim.

This upper door trim is the replacement trim piece that restores a clean finished edge at the top of the refrigerator/freezer door. It improves appearance and helps maintain a proper door seal and alignment. What it does

• Replaces cracked, dented, or warped top door trim that affects appearance
• Covers and protects the upper door edge from impact and wear
• Helps maintain an even door gap and support proper gasket seating
• Stops drafts or light leaks caused by damaged trim

• One upper door trim piece

• High-level task: remove the door or open as needed, remove screws or clips securing the old trim, and attach the new trim with the original fasteners
• Use proper hand tools; avoid over-tightening screws that can crack the trim
• Support the door while working to prevent hinge or alignment stress

Dairy and utility compartment divider for 42 and 48 inch GE/Monogram refrigerators.

This is the fresh food side bottom door hinge. For top door hinge use WR13X633.

Replacement screw that secures panels and internal components, helping stop rattles and keep parts aligned. Use it to replace stripped, rusted, or missing fasteners and restore a secure fit. What it does:

• Secures panels, trim, or internal parts to prevent movement and vibration.
• Replaces worn, corroded, or missing screws that cause loose panels or rattling.
• Restores proper alignment for doors, covers, and mounted components.
• Provides a simple hardware fix that helps maintain safe, stable operation.

• Always disconnect power to the appliance before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head; apply firm but controlled torque.
• Verify screw length, head style, and thread type match the original before installation.
• If threads are damaged, replace with a matching OEM screw rather than over-tightening.