Parts for Ge ZISS48DCBSS: 02 - Fresh Food Door Parts

This .030-inch shim is a thin leveling spacer used to correct small height and alignment gaps. It helps stabilize and align appliance components for proper fit and reduced vibration during operation. What it does:

• Provides a precise 0.030-inch thickness to raise or level panels, doors, or chassis components
• Helps eliminate small gaps that can cause rubbing, misalignment, or uneven sealing
• Reduces vibration or rocking by evening out contact points and load distribution
• Useful during cabinet installation or when replacing worn leveling feet or brackets

• Disconnect power (and water if applicable) to the appliance before performing service
• Use appropriate hand tools and keep shims flat and properly seated under the component being adjusted
• Add shims incrementally—do not force parts into position or over-tighten fasteners after shimming

Restore a tight, energy-saving seal on your refrigerator. This magnetized fresh-food door gasket keeps cold air in and warm air out, helping maintain temperature, reduce frost and moisture, and prevent the compressor from overworking.

• Seals the refrigerator compartment door to the cabinet
• Helps maintain stable temperatures and humidity
• Can reduce condensation, frost buildup, and energy loss from air leaks
• Worn or torn gasket may cause doors not to seal, warm spots, or excess run time

• Unplug appliance before service; wear cut-resistant gloves
• Soften gasket in warm water or with a hair dryer on low to ease installation
• Remove retaining screws or pull from retainer (design varies), then seat new gasket fully in the groove
• Check for uniform contact all around; adjust door hinges/leveling if needed

This pack contains twelve replacement screws used to fasten appliance panels, trim, and components. They restore secure mounting and help stop rattling, loose panels, and gaps for a safer, quieter appliance. What it does:

• Secures exterior and interior panels, brackets, and trim pieces
• Restores proper fit where missing or stripped screws cause movement or noise
• Helps maintain appliance alignment and prevents parts from vibrating loose
• Used for general-purpose repairs on compatible GE appliances

• Disconnect power or unplug the appliance before performing any internal repairs
• Use the correct screwdriver bit and avoid overtightening to prevent stripping threads
• Keep remaining screws in a labeled container for future service
• If a screw does not seat easily, stop and verify correct fit to avoid damage

This euro standoff kit provides the mounting hardware used to secure trim panels and components on compatible appliances, restoring proper panel alignment and preventing rattles or loose trim. It's a direct-fit replacement for the listed part number. What it does:

• Replaces worn or damaged mounting standoffs that hold panels or trim in place
• Restores secure panel attachment to reduce vibration, rattling, or misalignment
• Helps maintain proper spacing between panels and cabinet for correct fit and finish
• Designed to match the original part's fit and function for reliable repair

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove affected trim/panel carefully to access standoffs; retain screws and hardware
• Install standoffs in the original locations and tighten screws until snug — do not overtighten
• If alignment issues persist after replacement, check adjacent clips, fasteners, and mounting surfaces

This is a refrigerator handle kit. This kit includes one handle that has a stainless steel finish. The purpose of the handle is to provide a piece to hold onto to open the refrigerator door. The handle could become damaged if it comes into forceful impact with another object. It can become dented or scratched. If the stainless steel finish begins to wear over time, this part will be a high-quality replacement. Save the screws from the original handle to install the one one. Replacing this part is very easy and can be done quickly by following the installation instructions. Some people may wish to wear work gloves to protect their hands during the replacement process.This specific handle kit is compatible with refrigerator units that are manufactured by the General Electric brand, including Hotpoint and RCA. It is sold individually and is sourced directly from the manufacturer.

This is a #10-32 x 3/4 truss-head screw designed to fasten small appliance panels and components securely. It replaces missing or worn fasteners to restore stable mounting and reduce rattles or movement. What it does:

• Secures trim, control panels, brackets, and small assemblies
• Restores tight mounting to stop panel vibration or rattling
• Keeps electrical and mechanical components properly aligned
• Works where a #10-32 machine screw with a short 3/4" length and truss head is required

• Disconnect power before working on the appliance
• Use the correct screwdriver or nut driver to avoid stripping the head
• Tighten until secure; avoid over-tightening which can strip threads or crack plastic
• Keep removed hardware organized for reinstallation

This screw set contains #10-32 thread fasteners used to secure appliance panels and components. It provides direct-fit replacement screws to restore proper fastening and stop loose or rattling parts. What it does:

• Replaces missing or damaged #10-32 screws used on appliances
• Secures panels, brackets, trim pieces, and internal components
• Helps eliminate rattling, vibration noise, and loose fittings
• Restores factory fastening for safe, stable operation

• Disconnect power and water before servicing the appliance
• Keep small parts organized and use a magnetic tray to avoid loss
• Use the correct driver to avoid stripping screw heads; do not overtighten

This is the fresh food side top door hinge. For bottom door hinge use WR13X766.

Fresh food side bottom hinge shim.

Dairy and utility compartment divider for 42 and 48 inch GE/Monogram refrigerators.

Hinge kit for 36/42/48 inch side by side GE/Monogram refrigerators.