Parts for Crosley CFD27SDPS0: Fresh Food Doors Parts

The Fresh Food Door Gasket is an OEM replacement part for Frigidaire refrigerators. It creates a seal around the refrigerator door to maintain a consistent temperature by keeping cold air in and warm air out. This helps ensure proper refrigerator conditions and prevents energy loss.

Over time, gaskets can degrade due to wear, exposure to extreme temperatures, or cleaning with harsh chemicals. A damaged or worn gasket may fail to seal properly, affecting the freezer's efficiency and potentially leading to increased energy consumption.

Symptoms of a bad gasket include:

• Frost or ice buildup inside the refrigerator
• Difficulty keeping the refrigerator door fully closed
• Warm air entering the refrigerator, causing temperature fluctuations
• Increased energy bills due to inefficient operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

NOTE: GASKET NOW GRAY, NOT WHITE

This stop is a small mounting hardware component that positions and limits movement of a nearby part, helping keep doors and panels aligned and preventing overtravel. It's a simple replacement that restores correct stopping action. What it does:

• Provides a fixed contact point to stop or limit movement of a door, panel or linkage
• Keeps parts aligned and prevents banging or overtravel
• Worn or broken stops can cause rubbing, misalignment, or noisy operation
• Restoring the stop often eliminates play and improves fit and function

• Disconnect power or unplug the appliance before starting any repair
• Remove any panels or trim needed to access the mounting location
• Replace the stop using the original fastener(s); hand-tighten then secure as needed

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

Replacement shaft bushing that supports and reduces wear on a rotating shaft or pivot, helping restore smooth, quiet movement and reduce wobble where the original bushing has worn or failed. What it does

• Provides a low-friction bearing surface for a rotating shaft or pivot to prevent metal-on-metal wear.
• Restores proper alignment and reduces shaft wobble that can cause noise or uneven operation.
• Helps stop squeaks, grinding, or rough movement caused by a worn or damaged bushing.
• Protects housing and shaft from accelerated wear by keeping components centered.

• Disconnect power or unplug the appliance before beginning any repair.
• Remove access panels and any fasteners needed to reach the worn bushing; support the shaft while removing the old bushing.
• Inspect the shaft and mating surfaces for wear or damage and clean before installing the new bushing.
• Press the new bushing into place gently and evenly; avoid excessive force. Reassemble and test operation before returning the appliance to service.

This bushing provides a durable, low-friction bearing surface between moving parts in your appliance. It helps components pivot or rotate smoothly, reducing noise and wear so doors, drawers, and mechanisms operate as intended.

• Provides a sleeve/bearing surface between a pin or shaft and its housing
• Maintains alignment to prevent wobble and binding
• Reduces friction, squeaks, scraping, and premature wear
• When worn or missing, movement may feel rough, loose, or noisy

• Disconnect power before servicing
• Support the assembly being serviced before removing fasteners
• Note the orientation of the original bushing; seat the new bushing fully without forcing
• Reassemble and check for smooth, rub-free movement before restoring power

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power

The Door bin is an OEM replacement part for Frigidaire refrigerators. It is a built-in storage compartment designed to hold commonly used items like eggs, butter, or condiments. The door bin provides convenient access to the refrigerator door.  

Causes of a bad door bin can include cracked or broken plastic, damaged sliding tracks that prevent smooth opening and closing, or broken mounting tabs that cause it to become loose or detached from the refrigerator door.

Symptoms of a bad door bin include:

• Items falling out of the bin easily  
• The bin not closing or securing properly
• Difficulty opening and closing the bin
• Noise or vibration from a loose or damaged bin

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models. 

The Door Bin is an OEM replacement part for Frigidaire refrigerators. The door bin is responsible for organizing smaller items and optimizing interior space utilization. It measures approximately 5" depth x 12 1/2" width x 3" height.

Causes of a bad door bin can include damage such as cracks or breaks in the plastic, broken adjustable shelves, or issues with the mounting brackets that secure it inside the refrigerator door. 

Symptoms of a bad door bin include:

• Items falling out of the bin due to structural integrity issues
• Difficulty accessing storage areas due to broken shelving  
• The bin not sitting securely inside the door

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This Door Bin is an OEM part for Frigidaire refrigerators. This bin is located on the interior side of the refrigerator door, providing convenient storage space for items such as bottles, jars, and condiments. It helps keep the refrigerator organized and maximizes available storage.

Causes of a bad door bin can include wear and tear, accidental damage, or improper handling.

Symptoms of a bad door bin may include:

• Cracks or breakage in the bin
• Difficulty in securely holding items
• Limited storage capacity due to a damaged or missing bin

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Hinge Pin is an OEM part for Frigidaire refrigerators. It is responsible for supporting the mullion or flapper, which is the vertical strip that divides the refrigerator doors. It provides smooth movement and proper alignment of the mullion, allowing it to pivot easily for access to both compartments while maintaining an airtight seal when closed.

Causes of a bad hinge pin can include wear and tear over time, accidental damage, or improper handling. A damaged or worn-out hinge pin may result in difficulties in opening or closing the mullion.

Symptoms of a bad Hinge Pin include:

• Difficulty in opening or closing the doors
• Excessive play or wobbling of the mullion
• Failure to maintain a proper seal between door
• Unusual noises during use

This OEM Frigidaire part can also be used on select Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore models.

This replacement magnet is used in select refrigerator assemblies. It provides the magnetic hold or sensor trigger required so doors, flaps, or rails stay closed and so the controls can accurately detect when components are in position.

• Supplies magnetic retention in the specified assembly to keep parts closed and aligned
• Activates magnetic reed sensors in models that use them for door/position detection
• Weak or missing magnets can lead to door-ajar alerts, air leaks, or components not staying shut
• Visible damage or incorrect orientation can cause intermittent operation or improper sealing

• Disconnect power before servicing; turn off water if working near the dispenser
• Use your model's parts diagram to locate the magnet and note its orientation/polarity
• Press-fit into its holder carefully; do not chip or crack the magnet
• Verify proper closure/sensing operation before returning the appliance to service

This refrigerator door mullion is the flip-up divider attached to the fresh food door that covers the gap between doors. It helps the doors seal properly, limiting air leaks and moisture at the center seam for consistent cooling performance. What it does and common symptoms:

• Flips into place as the door closes to create the center seal between doors
• Helps maintain interior temperature and reduce condensation at the door seam
• Replace if cracked, warped, loose, or not springing/aligning with the door gasket
• Symptoms can include doors not latching cleanly, visible damage, or moisture along the middle

• One door mullion assembly

• Unplug the refrigerator before servicing
• Remove door bins if needed; support the mullion and remove the mounting screws
• Lift the mullion off its pivots, position the new part, and reuse existing hardware to secure it
• Verify smooth flip action and a tight seal before restoring power

This replacement guide aligns and supports a moving component so it travels on its intended path without binding. Replacing a worn or broken guide restores smooth operation and helps prevent scraping, jamming, or premature wear of connected parts.

• Keeps the associated rack, drawer, or panel centered and properly aligned during movement
• Provides a track/stop for the mating part to follow
• Reduces friction and noise for smoother sliding
• Typical failure signs: sticking, uneven travel, scraping noises, or visible cracks/broken tabs

• Disconnect power; also shut off water or gas
• Remove the associated assembly to access the guide and note its orientation
• Reuse original screws/clips and tighten securely without overtightening
• Test movement after installation; replace worn mating rails or rollers if needed

This is the vertical flipper mullion assembly that mounts to one fresh-food door and pivots closed to seal the center gap when both refrigerator doors are shut, helping maintain proper temperature and energy efficiency.

• Creates the center seal between French-door refrigerator doors
• Helps prevent warm air infiltration and moisture/condensation in the fresh-food section
• Common failure signs include a loose or broken hinge, mullion not staying aligned, condensation at the door center, or doors not sealing properly
• May also be noted if doors pop open or temperature fluctuates in the refrigerator compartment

• Unplug the refrigerator before servicing
• Remove door bins to access mounting screws/clips
• Transfer any original covers or hardware if not part of the new assembly
• Verify proper hinge engagement so the mullion flips and seals smoothly before restoring power

The Flapper Door Center Hinge is an OEM part for Frigidaire refrigerators. This hinge is essential for the proper operation of the flapper door, which helps seal the gap between the refrigerator doors when they are closed, ensuring efficient cooling and energy use.

Over time, the center hinge can wear out or become damaged due to regular opening and closing of the refrigerator doors. Accumulation of dirt, dust, or debris, as well as physical impact, can also contribute to hinge failure.

Symptoms of a bad flapper door center hinge include:

• The flapper door not closing properly
• Gaps between the refrigerator doors
• Increased energy consumption due to cold air escaping
• The refrigerator doors not aligning correctly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This housing is the replacement cabinet housing that provides structural support and protects internal components, restoring proper fit and appearance. It helps stabilize assemblies and keeps wiring and parts shielded from damage. What it does:

• Replaces a cracked, broken, or dented cabinet housing to restore structural integrity
• Protects internal components and wiring from debris and accidental contact
• Helps reduce rattling or movement caused by damaged housing
• Restores the appliance's proper fit and alignment for panels and doors

• One housing

• Disconnect power to the appliance before starting any repair
• Use appropriate hand tools; support adjacent panels to avoid stress on clips or fasteners
• Watch for sharp edges; wear gloves and eye protection

This small permanent magnet is used in supported refrigerator assemblies to actuate a mating reed switch or metal keeper. It helps the appliance recognize a closed position or hold a light cover/door closed for proper operation. What it does:

• Works with a reed switch or ferrous keeper to provide position sensing or magnetic latching
• Helps ensure features dependent on closed position operate correctly
• Can resolve issues where a small cover or door won't stay closed
• Address erratic "door ajar" indications tied to magnetic sensing

• Disconnect power and water before servicing
• Note the original magnet's location and orientation; polarity matters for proper operation
• Seat the magnet fully in its pocket or holder and align with the mating switch/keeper
• Test the related function before reassembling panels and trim

This small rubber bumper cushions the refrigerator/freezer door to reduce noise and prevent metal-on-metal contact. It helps doors close quietly and protects cabinet finish from repeated impacts. What it does:

• Acts as a soft stop between the door and cabinet/frame to absorb impact
• Reduces rattling and slamming for quieter operation
• Prevents wear and chipping where the door contacts the cabinet
• Restores proper door alignment when missing or worn

• One replacement bumper

• Push the bumper into the existing hole or slot on the door/frame until fully seated
• Inspect surrounding area for damage; replace mounting clips or retainers if required
• Wear gloves to protect hands from sharp edges during installation
• No special tools usually required; for detailed instructions

This 3/32" screwdriver is the service tool used to access and adjust small screws on appliances, making routine panel and control adjustments easier and more precise. Handy for basic repairs and maintenance. What it does:

• Fits 3/32" slotted screws commonly found on control panels, trim, and small fasteners
• Allows removal and installation of small service screws for access to internal components
• Helps correct loose screws that can cause rattling or misaligned panels
• Provides better fit than oversized drivers to reduce screw head damage

• Always disconnect power to the appliance before performing service or repairs
• Use the correct 3/32" blade size to avoid stripping screw heads
• Apply steady pressure and avoid excessive torque; use hand force only unless otherwise specified

This genuine replacement screw secures appliance components and restores proper fit and stability. Use it to replace a missing or damaged fastener and stop panels, trim, or parts from shifting or rattling during normal use. What it does:

• Fastens and holds panels, brackets, or small components in place
• Restores secure attachment when an original screw is missing, damaged, or stripped
• Helps eliminate vibration, rattling, or loose-fitting parts
• Matches the OEM fit and function for reliable reassembly

• Use correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and remove food or contents from appliance areas as needed before servicing
• If fastener threads are damaged, replace with the exact OEM screw rather than forcing installation

This is a service wrench used to loosen and tighten appliance fasteners for maintenance and repairs, making access and part replacement easier for technicians and DIYers. Durable tool designed for specific appliance fastener sizes. What it does:

• Provides the correct fit and leverage for removing or installing designated appliance nuts, bolts, and fittings
• Helps safely access internal components during service and part replacement
• Reduces risk of rounding fasteners compared with improvised tools
• Useful for routine maintenance tasks and repair procedures that require a dedicated wrench

• One wrench

• Use the wrench only for its intended appliance fasteners; avoid excessive force
• Disconnect power and water to the appliance before beginning service
• Wear safety gloves and eye protection when working on appliances

This Mullion harness routes electrical connections through the refrigerator door mullion so lights, sensors and control/LED assemblies communicate with the main cabinet wiring. It restores reliable power and signal routing in the door center strip. What it does:

• Carries power and signal between the door/mullion components and the main harness
• Restores non-functioning mullion lights, LEDs or control communication caused by a damaged harness
• Prevents intermittent connections from frayed or broken mullion wiring
• Used when visible wire damage or connector failure is found in the mullion area

• One (1) mullion harness as pictured

• Disconnect power to the appliance before starting work to avoid shock or injury
• Remove the mullion/door trim and any gaskets per service instructions to access the harness
• Inspect connectors and wire routing; replace any clips or retainers to prevent pinching