Parts for Frigidaire FPBC2278UF1: Fresh Food Doors Parts

The Frigidaire PureSource Ultra II Refrigerator Water & Ice Filter is an OEM part for Frigidaire refrigerators provides clean, fresh-tasting water and ice. This advanced filtration system is specifically engineered to remove impurities and contaminants from your water supply, including lead, chlorine, mercury, and certain pesticides, without removing beneficial fluoride. 

Regular replacement of the water and ice filter is crucial for maintaining the quality of your drinking water and the efficiency of your refrigerator's water and ice dispensing system. Over time, filters can become saturated with contaminants, reducing their effectiveness and potentially impacting the taste and safety of your water.

Symptoms of a filter in need of replacement include:

• Reduced water flow from the dispenser
• Unpleasant taste or odor in the water and ice
• The refrigerator's water filter indicator light turning on

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Fresh Food Door Gasket is an OEM replacement part for Frigidaire refrigerators. It creates a seal around the refrigerator door to maintain a consistent temperature by keeping cold air in and warm air out. This helps ensure proper refrigerator conditions and prevents energy loss.

Over time, gaskets can degrade due to wear, exposure to extreme temperatures, or cleaning with harsh chemicals. A damaged or worn gasket may fail to seal properly, affecting the freezer's efficiency and potentially leading to increased energy consumption.

Symptoms of a bad gasket include:

• Frost or ice buildup inside the refrigerator
• Difficulty keeping the refrigerator door fully closed
• Warm air entering the refrigerator, causing temperature fluctuations
• Increased energy bills due to inefficient operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

NOTE: GASKET NOW GRAY, NOT WHITE

The Nameplate is an OEM for Frigidaire appliances. It affixes to the exterior and clearly identifies the brand.

Causes of a damaged nameplate can include normal wear and tear over time outdoors, exposure to cleaning chemicals that breakdown adhesive integrity or accidental damage from impact.

Symptoms of a bad nameplate include:

• Nameplate lifted, peeling or completely removed from surface
• Faded or worn lettering obscuring model identification
• Dirty, stained appearance detracting from product aesthetics

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Stop is an essential OEM replacement part for Frigidaire bottom-mount refrigerators. It functions to securely hold the refrigerator door fully open during loading and unloading of food items. 

Causes of a faulty door stop include cracking or warping due to years of resisting door closure force during access. Friction might also wear down moving lever components over time.

Symptoms of a bad door stop are:

• Refrigerator door unable to safely prop fully open  
• Door slowly closing partially while items are retrieved
• Visible wear marks or loss of lubrication where door pivots

This authentic OEM replacement is compatible for Frigidaire, Electrolux and Kenmore models. 

This door stop is the replacement part that limits door travel and cushions the refrigerator door for smoother closing and reduced impact. It helps restore proper door alignment and prevents the door from hitting the cabinet. What it does:

• Stops or limits door travel to prevent over-opening and cabinet damage
• Cushions door movement to reduce slamming and wear on hinges
• Helps maintain correct door alignment so the seal engages properly
• Commonly used when the door hangs unevenly, slams, or won't stay aligned

• Disconnect power or unplug the appliance if accessing electrical components is required.
• Support the door or remove it before replacing hinge or stop hardware.
• Basic hand tools usually required; keep track of small screws and clips.
• Test door operation and alignment after installation; adjust as needed.

This right-hand stainless refrigerator door replaces a damaged or dented outer door panel and restores proper appearance and closure. It fits the refrigerator's fresh-food compartment and keeps internal temperatures stable when the door seals correctly. What it does

• Replaces a bent, dented, or cosmetically damaged right-side outer refrigerator door
• Restores proper door alignment and helps the gasket seal fully to maintain cooling efficiency
• Stops light, drafts, or moisture entry caused by warped or cracked door panels
• Improves appliance appearance with a stainless finish

• Disconnect power to the appliance before starting any work
• Use two people or proper lifting support; door panels can be heavy and awkward
• Handle edges and any glass with care to avoid cuts or breakage
• Reuse or replace hinges, screws, and gasket hardware as required per vehicle-specific diagram

This door handle assembly provides a ready-to-install replacement to restore a secure, easy-grip opening for your refrigerator door. Durable construction replaces a worn or broken handle for reliable daily use. What it does:

• Replaces a cracked, loose, or broken refrigerator door handle to restore safe operation and appearance
• Provides a solid grip for opening and closing the door smoothly
• Matches factory mounting points for proper fit and alignment
• Helps prevent door damage and keeps the seal functioning by ensuring correct door movement

• Disconnect power to the appliance before beginning any repair to avoid injury
• Remove any trim or access panels as needed to access mounting screws; retain fasteners for reassembly
• Hand-tighten screws, then snug—do not overtighten to avoid cracking the handle or trim

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power

The Door Bin is an OEM part for Frigidaire refrigerators. It is located on the lower part of the refrigerator door, designed to hold larger items such as gallon-sized containers or tall bottles.

A bad door bin can be caused by damage, wear and tear, or improper handling. Signs of a faulty bin include cracks, warping, or missing pieces.

Symptoms of a bad door bin can include:

• Visible cracks, chips, or warping
• Difficulty in securely storing or retrieving items
• Damaged or missing bin.

Replace your damaged or worn-out refrigerator door bin with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This refrigerator door shelf bin mounts to the inner door liner to hold bottles, jars, and condiments. Replace a cracked or missing bin to restore organized on-door storage and keep frequently used items within easy reach. What it does:

• Provides on-door storage for beverages, condiments, and small containers
• Helps keep items upright and accessible
• Restores capacity when the original bin is cracked or missing
• Common symptoms: broken or warped plastic, broken mounting tabs, bin won't stay seated or falls off

• 1 door bin

• Empty the old bin and lift up to release it from the door liner tabs
• Align the new bin with the same tabs and press down until fully seated
• Do not force; confirm you're using the correct location/style for your model
• No tools typically required; handle plastic edges carefully

The Door Bin is an OEM part for Frigidaire refrigerators. This bin is designed to fit securely on the refrigerator door, providing convenient storage for bottles, jars, and other items. It helps maximize the use of space within the refrigerator, allowing for better organization and accessibility of frequently used products.

Over time, door bins can become damaged or worn out due to regular use, overloading, or accidental impacts. Common causes of a bad door bin include cracks, breaks, or the plastic becoming brittle and snapping off.

Symptoms of a bad door bin include:

• Cracks or breaks in the plastic
• Difficulty in securely attaching the bin to the door
•  Items falling out of the bin
• Reduced storage capacity on the refrigerator door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This Door Bin is an OEM part for Frigidaire refrigerators. This bin is located on the interior side of the refrigerator door, providing convenient storage space for items such as bottles, jars, and condiments. It helps keep the refrigerator organized and maximizes available storage.

Causes of a bad door bin can include wear and tear, accidental damage, or improper handling.

Symptoms of a bad door bin may include:

• Cracks or breakage in the bin
• Difficulty in securely holding items
• Limited storage capacity due to a damaged or missing bin

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Hinge Pin is an OEM part for Frigidaire refrigerators. It is responsible for supporting the mullion or flapper, which is the vertical strip that divides the refrigerator doors. It provides smooth movement and proper alignment of the mullion, allowing it to pivot easily for access to both compartments while maintaining an airtight seal when closed.

Causes of a bad hinge pin can include wear and tear over time, accidental damage, or improper handling. A damaged or worn-out hinge pin may result in difficulties in opening or closing the mullion.

Symptoms of a bad Hinge Pin include:

• Difficulty in opening or closing the doors
• Excessive play or wobbling of the mullion
• Failure to maintain a proper seal between door
• Unusual noises during use

This OEM Frigidaire part can also be used on select Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore models.

This replacement magnet is used in select refrigerator assemblies. It provides the magnetic hold or sensor trigger required so doors, flaps, or rails stay closed and so the controls can accurately detect when components are in position.

• Supplies magnetic retention in the specified assembly to keep parts closed and aligned
• Activates magnetic reed sensors in models that use them for door/position detection
• Weak or missing magnets can lead to door-ajar alerts, air leaks, or components not staying shut
• Visible damage or incorrect orientation can cause intermittent operation or improper sealing

• Disconnect power before servicing; turn off water if working near the dispenser
• Use your model's parts diagram to locate the magnet and note its orientation/polarity
• Press-fit into its holder carefully; do not chip or crack the magnet
• Verify proper closure/sensing operation before returning the appliance to service

This refrigerator door mullion is the flip-up divider attached to the fresh food door that covers the gap between doors. It helps the doors seal properly, limiting air leaks and moisture at the center seam for consistent cooling performance. What it does and common symptoms:

• Flips into place as the door closes to create the center seal between doors
• Helps maintain interior temperature and reduce condensation at the door seam
• Replace if cracked, warped, loose, or not springing/aligning with the door gasket
• Symptoms can include doors not latching cleanly, visible damage, or moisture along the middle

• One door mullion assembly

• Unplug the refrigerator before servicing
• Remove door bins if needed; support the mullion and remove the mounting screws
• Lift the mullion off its pivots, position the new part, and reuse existing hardware to secure it
• Verify smooth flip action and a tight seal before restoring power

This replacement guide aligns and supports a moving component so it travels on its intended path without binding. Replacing a worn or broken guide restores smooth operation and helps prevent scraping, jamming, or premature wear of connected parts.

• Keeps the associated rack, drawer, or panel centered and properly aligned during movement
• Provides a track/stop for the mating part to follow
• Reduces friction and noise for smoother sliding
• Typical failure signs: sticking, uneven travel, scraping noises, or visible cracks/broken tabs

• Disconnect power; also shut off water or gas
• Remove the associated assembly to access the guide and note its orientation
• Reuse original screws/clips and tighten securely without overtightening
• Test movement after installation; replace worn mating rails or rollers if needed

The Flipper Mullion Assembly is an OEM part for Frigidaire refrigerators. It is an exterior part that seals the refrigerator door and houses the water and ice dispenser on select models. The flipper mullion assembly attaches both side by side doors together and operates the dispenser and door functions.

Causes of a bad mullion assembly can include damage from door impacts, wear from years of door swing motions, or failure of seals or gaskets.

Symptoms of a bad Flipper Mullion Assembly include:

• Gaps or air leaks around the refrigerator doors when closed
• Loose, sagging or misaligned doors
• Dispenser components like the water valve not functioning properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
 

The Flapper Door Center Hinge is an OEM part for Frigidaire refrigerators. This hinge is essential for the proper operation of the flapper door, which helps seal the gap between the refrigerator doors when they are closed, ensuring efficient cooling and energy use.

Over time, the center hinge can wear out or become damaged due to regular opening and closing of the refrigerator doors. Accumulation of dirt, dust, or debris, as well as physical impact, can also contribute to hinge failure.

Symptoms of a bad flapper door center hinge include:

• The flapper door not closing properly
• Gaps between the refrigerator doors
• Increased energy consumption due to cold air escaping
• The refrigerator doors not aligning correctly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Right Door Closer is an OEM part for Frigidaire refrigerators. It is responsible for ensuring that the refrigerator door closes securely and maintains a proper seal, keeping the cold air inside and your food fresh.

A bad right door closer can be caused by wear and tear, damage, or misalignment. When the closer becomes faulty, it can result in issues such as a loose or sagging door, difficulty in closing the door properly, or a compromised seal that leads to temperature fluctuations.

Symptoms of a bad right door closer include:

• Door not closing or sealing properly
• Condensation or frost buildup inside the refrigerator
• Noisy or squeaking door operation

Replace your faulty right door closer with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This left-hand door closer replaces the refrigerator/freezer door closer that helps the door swing closed smoothly and stay aligned for a proper seal. Restores reliable closing and reduces door sag or misalignment. What it does:

• Guides and supports the left-side door as it closes to prevent slamming and ensure proper latch engagement
• Helps maintain an even seal to preserve internal temperature and reduce energy loss
• Reduces door sag, rubbing, or uneven gaps caused by worn or broken closers
• Works with the existing hinge/door hardware to control door motion

• High-level replacement — remove the door trim/inner panel to access the closer if required
• Keep screws and brackets organized; verify orientation for left-hand side before fastening
• Disconnect power to the appliance or follow manufacturer's safety guidance when working near electrical components

This genuine replacement screw secures appliance components and restores proper fit and stability. Use it to replace a missing or damaged fastener and stop panels, trim, or parts from shifting or rattling during normal use. What it does:

• Fastens and holds panels, brackets, or small components in place
• Restores secure attachment when an original screw is missing, damaged, or stripped
• Helps eliminate vibration, rattling, or loose-fitting parts
• Matches the OEM fit and function for reliable reassembly

• Use correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and remove food or contents from appliance areas as needed before servicing
• If fastener threads are damaged, replace with the exact OEM screw rather than forcing installation

A replacement inner cabinet liner that restores the smooth, sealed interior surface of the refrigerator compartment for proper food storage and easy cleaning. Replaces cracked, stained or warped liners to reduce leaks and odors. What it does:

• Provides the finished interior surface that holds shelves, bins and drawers in place
• Restores a watertight, easy-to-clean surface to prevent pooling and mold growth
• Stops drafts and insulation exposure caused by cracks or delamination
• Helps maintain proper airflow and temperature distribution inside the cabinet

• Disconnect power and remove all food, shelves and drawers before starting.
• Handle carefully to avoid cracking the new liner during installation.
• Follow OEM instructions.

This Mullion harness routes electrical connections through the refrigerator door mullion so lights, sensors and control/LED assemblies communicate with the main cabinet wiring. It restores reliable power and signal routing in the door center strip. What it does:

• Carries power and signal between the door/mullion components and the main harness
• Restores non-functioning mullion lights, LEDs or control communication caused by a damaged harness
• Prevents intermittent connections from frayed or broken mullion wiring
• Used when visible wire damage or connector failure is found in the mullion area

• One (1) mullion harness as pictured

• Disconnect power to the appliance before starting work to avoid shock or injury
• Remove the mullion/door trim and any gaskets per service instructions to access the harness
• Inspect connectors and wire routing; replace any clips or retainers to prevent pinching

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head