Parts for Ge PGB965BP1TS: Gas & Burner Parts

This LP conversion kit assembly converts a compatible gas range or oven from natural gas to liquid propane so the appliance can operate correctly after a fuel change. It provides the correct fuel delivery components needed for conversion when used as directed. What it does:

• Supplies the parts required to convert a compatible gas appliance from natural gas to LP
• Provides the correct orifice/regulator hardware to match LP fuel pressure
• Helps restore proper burner operation after converting fuel type
• Addresses symptoms related to incorrect fuel setup, such as weak or uneven flames after conversion

• Follow the appliance manufacturer's conversion instructions exactly and use only the kit specified for your appliance
• Shut off the gas supply and electrical power before starting work
• Install and adjust components per OEM procedures; use proper torque and fittings
• After installation, check all gas connections for leaks and verify safe operation

This LP high-altitude conversion kit adapts select gas cooking appliances for liquid propane use at elevation. It properly meters gas flow so burners light easily and produce clean, stable flames in thin-air conditions.

• Configures the appliance for LP operation in high-altitude installations
• Calibrates fuel delivery to maintain proper flame size and combustion
• Helps address yellow/sooty flames, flame lift, or hard-to-control simmer after conversion
• Promotes reliable ignition and even heat across burners

• Conversion affects gas type and pressure; must be performed per the manufacturer's instructions and local codes
• Shut off gas and power before service; work in a well-ventilated area away from open flames or sparks
• After conversion, leak-test all connections and adjust air shutters per model guidance if applicable
• Intended for LP high-altitude applications only; use the model-specific kit specified by the manufacturer

The Range NG High Altitude Kit is an OEM part for GE gas ranges. This high-altitude conversion kit allows the range to operate properly at elevations above 2000 feet.

Causes related to needing this kit are using the range at a high elevation without proper adjustment for decreased air pressure and oxygen levels.

Symptoms of needing this high-altitude kit include:

• Unstable or inconsistent flame during operation
• Excessive cooking times
• Incomplete combustion of gas resulting in carbon monoxide issues

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This economic nut is a small replacement fastening nut that restores secure connections for appliance components. It replaces worn or missing hardware so panels and internal parts stay firmly seated and reduce vibration. What it does:

• Secures components and panels by threading onto the matching stud or bolt to hold assemblies in place
• Prevents loose or rattling panels and hardware caused by a missing or damaged nut
• Restores proper fit for user-accessible panels and internal brackets where this nut is specified
• Simple hardware replacement to regain stable mechanical connections

• Disconnect power and water (if applicable) and follow basic electrical safety before servicing the appliance
• Use the matching size wrench or socket; thread-on by hand first to avoid cross-threading, then snug—do not overtighten
• Inspect mating stud or bolt for damage; replace hardware that is stripped, corroded, or deformed

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

The Medium surface burner base is an OEM part for GE ranges. It serves as the base for the surface burners, covering and protecting the burner cavities.

Causes of a bad surface burner base include warping or deformation from high heat over time, cracks or breaks from impact damage, or corrosion from liquid spills or grease accumulation.

Symptoms of a bad surface burner base include:

• Burners no longer sitting flush or securely on the cooktop surface
• Excessive air gaps around the burners allowing gas/flames to escape
• Difficulty cleaning due to liquid leaks into the burner cavities
• Visible cracks, breaks, or deformities in the material

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This manifold pipe routes gas from the range's valve assembly to the individual cooktop burners, restoring safe and consistent fuel delivery for reliable burner operation. Replace a damaged or corroded manifold to stop leaks and restore proper flame distribution. What it does:

• Channels gas from the control valve block to each burner for ignition and steady flames
• Helps maintain even burner performance and consistent heat across the cooktop
• Failsafe for preventing gas leaks when intact; visible damage, corrosion, or cracks can cause unsafe operation
• Commonly replaced when burners won't light, show weak or irregular flames, or after leak detection

• Turn off the gas supply and unplug the appliance before servicing.
• Inspect and replace any damaged seals, gaskets, or fittings when installing the manifold.
• Test for leaks with a soap solution or approved leak detector after installation; do not use an open flame.

This small V2 inlet jet directs water flow to the dispenser/ice-making area so the appliance fills and forms properly. It restores correct water routing for consistent filling and helps reduce weak or misshapen ice or slow dispensing. What it does:

• Channels water to the ice maker/dispenser so the correct amount reaches the fill area.
• Helps ensure uniform ice formation and consistent dispenser flow.
• Can resolve symptoms like weak/slow dispensing, underfilled ice trays, or uneven ice cubes.
• Works as the small replacement nozzle where the original inlet jet is worn or blocked.

• One small V2 inlet jet

• Disconnect power and shut off the water supply before beginning work.
• Access may require removing inner panels or the ice maker/dispenser housing; follow your model's service instructions.
• Inspect the seat and surrounding fittings for debris or damage before installing; replace other damaged components as needed.

This genuine OEM GE replacement is compatible with additional Hotpoint, RCA and Kenmore gas range models.

A replacement burner valve cover that protects and conceals the gas valve assembly on compatible ranges, helping keep valve components clear of spills and debris for more reliable burner operation. What it does:

• Covers and protects the gas valve area from food, moisture and spills.
• Helps prevent debris from interfering with valve knobs and internal valve parts.
• Can reduce intermittent ignition or burner performance issues caused by contamination.
• Restores the finished appearance around the valve for safer, cleaner operation.

• Always shut off the gas supply and unplug the appliance before servicing.
• Use basic hand tools; handle the valve area gently to avoid disturbing fittings or tubing.
• After installation, check for gas leaks with a soapy-water solution or a proper leak detector—do not use an open flame.

This is the center-burner orifice holder for gas cooktops and ranges. It routes fuel from the surface valve to the burner and aligns the orifice for reliable ignition and consistent flame on the center burner.

• Directs gas from the valve to the center burner
• Holds the orifice in correct alignment beneath the burner head
• Provides the mounting point/interface for the center burner assembly
• Typical symptoms: center burner won't ignite, delayed ignition, weak/uneven flame, or visible damage/corrosion on the holder

• Disconnect power and shut off the gas supply before servicing
• Remove grates, caps, and burner head; lift/open the cooktop as needed to access the holder
• Transfer any model-specific orifice spud/fittings as directed by the manufacturer
• After reassembly, check all connections for leaks with an approved leak-detection solution and verify proper flame

This 1/4-20 screw secures panels, brackets, and other assemblies in your appliance. It restores a tight, reliable hold when an original fastener is missing, stripped, or corroded.

• Fastens components that require a 1/4-20 threaded screw
• Helps keep panels and assemblies aligned and rattle-free
• Direct replacement for worn, rusted, or lost hardware
• Common symptoms: loose or vibrating parts, misaligned brackets, missing fastener

• Disconnect power; turn off gas supply before servicing
• Allow the appliance to cool; wear gloves and eye protection
• Start threads by hand to avoid cross-threading; use the correct driver/tool
• Tighten snugly—do not overtighten to prevent stripping or damage

This orifice holder secures the gas orifice in the burner tube to ensure stable fuel delivery for consistent burner flames. It replaces a worn or damaged holder to restore correct orifice alignment and flame performance. What it does

• Holds the gas orifice in proper position inside the burner tube for accurate fuel flow
• Helps maintain consistent, even burner flames and reliable ignition
• Common replacement when burners show weak, uneven, or inconsistent flames
• Works with the stove's burner assembly to prevent orifice dislodgement during use

• One orifice holder

• Turn off the range's gas supply and unplug the appliance before starting work
• Remove burner grates and caps, then detach the burner tube to access the holder
• Inspect the orifice and surrounding components; replace the orifice if damaged

The Oven Orifice Spud LP is an OEM part for GE gas ovens. This part controls the flow of liquid propane (LP) gas into the oven burner box. The oven orifice spud plays a role in gas combustion, adjusting flow to match the needs of a liquid propane system. It connects directly to the gas supply, so an improperly sized or damaged spud can lead to gas leaks or incomplete burning.

Causes of a bad oven orifice spud include normal wear over time from constant heating cycles, exposure to cleaning chemicals, or damage during part replacement.

Symptoms of needing a replacement include:

• Uneven or inconsistent oven heating
• Extended cooking times or inability to reach desired temperatures
• Gas smell coming from the oven area
• Visible damage or cracks on the spud itself

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This orifice holder secures the burner orifice to a gas range or cooktop, positioning the orifice for a consistent gas flow and reliable ignition. Replaces a worn or damaged holder to restore correct burner alignment and flame performance. What it does:

• Holds the burner orifice in the correct position so gas flows properly to the burner
• Helps maintain an even, steady flame for consistent cooking performance
• Can resolve burner issues like weak or uneven flames or burners that fail to light
• Prevents orifice movement that can cause inefficient combustion or ignition problems

• One orifice holder

• Turn off the appliance and shut off the gas supply before starting; disconnect power if applicable
• Replace only with the correct OEM part for your model to ensure proper fit and orifice alignment
• Hand-start threads and tighten securely; avoid over-tightening which can damage the holder
• After installation, restore gas and power, then test burners and check for leaks (use a soapy water solution, never an open flame)

The Igniter Mounting Screw is an OEM replacement part for GE ovens and ranges. This screw secures the igniter to the burner assembly, ensuring it remains firmly in place for consistent and reliable ignition. Its precise fit and durable design help maintain the stability and functionality of the igniter.

Over time, mounting screws can become corroded, stripped, or lost during repairs or maintenance. A missing or damaged screw may result in a loose igniter, affecting the appliance's ability to ignite properly.

Symptoms of a bad or missing igniter mounting screw include:

• The igniter becoming loose or misaligned

• Difficulty securing the igniter during installation or repair
• The burner fails to ignite reliably or consistently
• Increased noise or movement of the igniter during operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This tubular broil burner delivers the concentrated heat used for broiling in gas ovens, restoring high-heat cooking performance for crisping and browning. Replace a damaged or worn broil tube to recover even broil results. What it does

• Provides the primary heat source for the oven's broil function
• Replaces a cracked, warped or visibly damaged broil tube
• Restores consistent top-heat for browning and finishing foods
• Addresses symptoms such as weak or no broil heat and uneven broiling

• Disconnect power and shut off gas supply before beginning service
• Handle the tube carefully to avoid bending or damaging terminals
• Verify proper fit and orientation against the oven's broil bracket and igniter

The Valve and Burner Assembly is an OEM part for GE gas ranges. As the primary mechanism for fuel ignition and burner operation, it works to deliver gas to each burner safely and control flame intensity precisely. 

Symptoms of a bad valve and burner assembly include:

• Inability to light one or more burners
• Unstable, excessively large or small flames  
• Burners that will not maintain the desired heat setting
• Gas leaks around the burner area

Causes can be normal damage over time from heat exposure, cracks developing in valve components, blockages in gas ports, or loose connections. Installing this OEM replacement ensures your range's burners operate efficiently.

This GE part is also compatible with some Hotpoint, RCA, and Kenmore ranges and restores reliable stove-top cooking performance. Replace yours today before minor problems worsen.
 

The BURNER VALVE is an OEM part for GE gas ranges. It regulates gas flow to individual cooktop burners, controlling flame size and heat output based on valve position.

Symptoms of a bad burner valve include: 

• Inability to adjust or maintain desired flame levels
• Gas odor or clicking/hissing noises from the burner area  
• Burners that remain constantly on without response to controls

Gas valves can weaken or crack over many heating/cooling cycles. Mineral buildup may also restrict precise flow regulation. Replacing the faulty valve with this genuine GE part restores the burners' heat-adjustable functionality for custom cooking power. 

This OEM GE replacement burner valve is also compatible with some Kenmore and RCA gas range models. Reliable control over burners maximizes versatility and safety.
 

This range burner valve controls gas flow to a single stovetop burner to restore reliable ignition and consistent flame control. Use it to replace a worn or leaky valve and help return safe, stable burner operation. What it does:

• Regulates gas delivery to one burner for proper ignition and flame adjustment
• Stops or reduces gas flow when the control is turned off to prevent leaks
• Helps resolve symptoms such as burners that won't light, weak or uneven flames, or persistent gas smell near a burner
• Works as the valve assembly that connects the cooktop knob to the burner gas line

• Turn off gas supply and electrical power to the appliance before beginning service
• Use appropriate tools and pipe sealant rated for gas if re-connecting gas lines
• After installation, test all connections for leaks with a soap solution or approved leak detector

The Burner Valve Assembly 270 is an OEM part for GE gas ranges. It controls gas flow to individual burners to deliver precise heating levels.  

Causes of a bad burner valve assembly include worn rubber diaphragms, debris inside valve channels, or damage from repeated heating cycles.

Symptoms are:

• Uneven cooking temperatures across burners
• Inability to ignite or adjust certain burners  
• Fluctuations in flame height/cooking output

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models.

The Valve Burner is an OEM component for GE gas ranges. Located below the grates atop each cooktop burner, it precisely mixes gas and air to provide controllable flames. A valve adjusts gas flow while perforated metal distributes the flame evenly. 

Symptoms of a faulty valve burner include: 

• Difficulty obtaining or maintaining set flame levels  
• Unstable or intermittent burner operation
• Yellow fire or flame that produces excessive soot
• No ignition or fire when the knob is turned

Causes can be wear of internal valve components, debris, or clogs in gas ports restricting flow over time. Damage from spills or dropped objects may also crack the burner.

This OEM GE burner is also compatible with models from Hotpoint and RCA.

This tube dual valve controls water flow through the appliance's tubing assembly, allowing proper delivery of water where the unit needs it. Replaces a worn or leaking valve to restore normal water supply and prevent leaks. What it does:

• Diverts or stops water flow through the machine's tubing when a valve is activated
• Helps prevent leaks caused by cracked, stuck, or corroded valve components
• Commonly used when the appliance doesn't fill, fills slowly, or constantly runs water
• Works as the plumbing control point for timed or solenoid-operated water delivery

• One tube dual valve

• Disconnect power and shut off the water supply before beginning work
• Handle tubing fittings and seals carefully to avoid damage and leaks
• Confirm the valve orientation and tubing routing match the original during reassembly

This inject burner assembly replaces a damaged or worn hob injector to restore proper gas flow to a cooktop burner. It provides the correct metered fuel delivery for consistent ignition and stable flame control. What it does:

• Directs and meters gas from the manifold into the burner for predictable burning
• Helps burners light promptly and maintain an even flame
• Can resolve weak flames, uneven heating, or failure to light when caused by the injector
• Works with the burner head and cap to form the complete burner flame assembly

• Turn off the gas supply and unplug the appliance before starting any work
• Inspect gaskets and fittings for leaks; replace or tighten per manufacturer guidance
• Use proper tools and follow OEM diagram orientation for correct installation

A 90° elbow assembly that redirects a fluid or discharge line at a right angle to restore proper routing and a secure connection. Simple replacement for worn, cracked, or damaged elbow fittings. What it does

• Redirects flow between two hoses or fittings at a 90° angle to enable correct line routing
• Provides a sealed connection to help prevent leaks where a straight connection won't fit
• Restores proper flow path to eliminate kinks or pressure loss caused by a damaged elbow
• Common symptom: visible leak, moisture or pooling near the elbow fitting
• Common symptom: poor or restricted flow where the line changes direction

• One 90° elbow assembly

• Turn off power and shut off the appliance water supply before starting any repair
• Inspect mating hoses and seals; replace worn clamps or gaskets for a reliable seal
• Hand-tighten then snug fittings; avoid over-tightening plastic fittings to prevent cracking
• After installation, restore water/power and check thoroughly for leaks during a test run

This 90° elbow assembly directs exhaust airflow in the oven/range vent path to ensure proper ventilation and heat flow. It replaces a damaged or cracked elbow to restore correct venting and maintain cooking performance. What it does:

• Routes exhaust and ventilation air through a 90° turn in the oven/range vent system
• Helps prevent heat or smoke from leaking into the cabinet area
• Commonly replaced when the original elbow is cracked, warped, or separated at the joint
• Supports consistent oven temperatures by keeping the vent path intact

• Disconnect power to the appliance before beginning any repair
• Access may require removing the oven back panel, rear trim, or adjacent components
• Use proper fasteners and gaskets where applicable; confirm orientation before fastening

The IGNITER GLOWBAR is an OEM component specifically designed for GE gas ranges. It functions as the direct source of ignition to light the oven.  

Causes of a bad igniter glowbar include decreased performance over time from frequent usage. Mineral deposits can accumulate, reducing its ability to generate sufficient spark. 

Symptoms of a bad igniter glowbar involve:

• Delayed ignition where gas must build up before lighting   
• Unreliable or intermittent ignition requiring multiple attempts
• Complete failure of one or more burners to ignite at all

Replacing the glowbar with this genuine GE part helps ensure dependable, easy burner ignition. Consistent glowbar performance is critical for safe range operation.

This OEM GE replacement glowbar is also compatible with various Kenmore, Hotpoint, and RCA gas range/cooktop models.
 

This dual safety valve controls water flow to two separate appliance water lines, restoring proper fill and preventing unwanted water flow. It's a direct-replacement valve used in appliances that require two independent water outlets. What it does:

• Directs and stops water flow to two separate water circuits when activated
• Prevents continuous or unintended filling if the valve fails
• Commonly linked to no-water-to-dispenser or no-water-to-ice-maker symptoms
• Can cause leaking or intermittent water flow when worn or damaged

• One dual safety valve

• Shut off power and water supply before starting any work
• Drain water lines and place a towel to catch residual water when disconnecting hoses
• Tighten fittings to OEM torque; check carefully for leaks after restoring water

The Igniter Glowbar is an OEM replacement part for GE ovens and ranges. This glowbar generates the pilot flame and ignites the main burner while cooking.

Causes of a bad glowbar can be prolonged or heavy use over time leading to degradation of the element, or damage from impact or mishandling during cleaning.

Symptoms of a bad glowbar include:

• Inability to ignite or light the oven burners
• Pilot light that repeatedly goes out
• Errors codes related to ignition issues
• Burned smell coming from the oven cavity

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is the hot surface igniter that glows to light the gas burner. A strong, reliable glow restores consistent oven ignition so preheats start promptly and baking temps stay steady.

• Heats up to ignite the bake or broil burner, allowing gas to light safely
• Weak, cracked, or open igniter can cause no-heat, delayed ignition, or oven not reaching temperature
• Intermittent oven heating or frequent burner cycling can also indicate a failing igniter

• Disconnect power and shut off gas before service; allow oven to cool
• Handle the ceramic igniter carefully—avoid touching the element; it is fragile
• Verify bracket orientation and wire connection style matches your original before install
• After installation, restore gas/electric and check for prompt ignition and normal flame

The Pressure Regulator is an OEM component designed specifically for GE gas ranges. Located outside the range near the supply line, this regulator controls incoming gas pressure to safe operation levels. 

Symptoms of a faulty regulator include:

• Unstable burner flame heights   
• Delayed or inconsistent ignition between burners
• Abnormal operating noises coming from the regulator

Causes usually involve wear of internal springs or diaphragms from years of sustained usage. Exposure to excessive pressure surges could also potentially damage regulator components over time.

This genuine GE regulator is compatible with select Hotpoint and RCA models as well.

This single safety valve controls gas flow to a single burner or heating circuit, restoring safe operation and preventing unintended gas flow. It's a direct replacement part used when the valve is faulty or leaks. What it does

• Regulates and stops gas flow to the appliance when required to maintain safe operation.
• Common symptom: burner or oven won't light or stay lit.
• Common symptom: detectable gas smell near the appliance or valve area.
• Restores normal ignition response when the original valve is worn or fails.

• One safety valve (single) as pictured.

• Turn off gas supply and electrical power before starting any service.
• After installation, check all connections for leaks using an approved leak test solution and restore gas pressure per manufacturer guidance.