Parts for Ge GFD49GRPK0RR: Gas Valve & Burner Assembly Parts

Black. 8-18 AB HXW 3/8

This temperature control thermostat regulates refrigerator temperature to help keep food properly chilled. Replaces a failed or intermittent control to restore consistent cooling. What it does:

• Senses internal cabinet temperature and opens/closes the circuit to the compressor or fans
• Can stop cooling if stuck open or cause continuous running if stuck closed
• Commonly used when fridge temperature is too warm, too cold, or fluctuates
• Works with mechanical temperature control systems

• Disconnect power to the appliance before removing the old thermostat or making any electrical connections
• Verify thermostat location and mounting style matches your appliance before installation
• Handle terminals gently; ensure secure wire connections and correct thermostat orientation

This dryer thermostat monitors internal temperature and helps regulate the heating cycle to protect against overheating. Replacing a failed thermostat restores proper heat cycling, helping your dryer heat consistently and operate safely. What it does:

• Senses exhaust/drum temperature and opens/closes to control power to the heater
• Helps prevent overheating by interrupting current when temperature exceeds its threshold
• Failure may cause no heat or low heat, extended dry times, overheating, or nuisance shutdowns

• 1 thermostat

• Disconnect power; turn off gas supply for gas models before servicing
• Access location per your model (commonly on the blower housing or heater assembly); note wire positions
• Transfer wires one at a time to the new thermostat and secure using existing hardware
• Remove lint buildup and verify airflow before test run

This radiant sensor is part of the gas dryer ignition circuit. It detects infrared heat from the igniter and burner so the gas valve only opens when ignition is present, restoring consistent and safe dryer heat.

• Detects heat from the igniter/flame and controls the gas valve circuit
• Enables safe ignition and helps maintain a steady burner flame
• Common symptoms: igniter glows but no flame, burner lights then goes out, no heat or intermittent heat, long dry times
• Used on gas dryer models

• Disconnect power and shut off gas supply before servicing; allow the burner area to cool
• Access the burner assembly; remove the lower/front panel as your model requires
• Move the wires, remove mounting screw(s), and install the new sensor in the same orientation; avoid touching the igniter
• If heating issues persist, also inspect the igniter and gas valve coils

This mounting bracket secures the chamber comb assembly inside the appliance so the comb stays aligned and stable during operation. It helps prevent rattling and movement of interior components for more reliable performance. What it does:

• Holds the chamber comb/comb assembly in the correct position inside the cavity
• Prevents the comb from shifting or vibrating during use
• Helps maintain proper alignment of related interior components
• Can stop noises or intermittent contact caused by a loose or broken bracket

• Disconnect power to the appliance before starting any repairs
• Basic hand tools required; remove interior panels or racks as needed to access the bracket
• Inspect adjacent parts and fasteners; replace any damaged clips or screws
• Tighten hardware securely but avoid overtightening to prevent damage

The GAS VALVE is an OEM part for GE gas dryers. It controls the gas flow from the supply line to the burner and dryer components requiring fuel. The gas valve opens and closes to carefully regulate gas levels during each phase of the drying cycle from ignition through the final cool-down. 

Symptoms of a faulty gas valve include:

• Difficulty or inability to ignite the burner flame  
• Unstable burner flame that periodically goes out
• Gas leaks detectable by sight or smell near the valve area
• Dryer not heating properly or cycles taking excessively long

Causes stem from normal wear over years of repeated usage. Failure could also arise from impact damage, dirt/debris accumulation, or internal component deterioration. 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This burner assembly replaces a damaged or worn surface burner on compatible gas cooktops, restoring reliable heating for everyday cooking. It provides a direct fit replacement to help get burners heating evenly and properly. What it does

• Delivers gas to the cooktop burner so pots and pans heat correctly
• Restores even flame distribution for consistent cooking results
• Helps resolve burners that produce weak or uneven flames
• Works with the cooktop ignition system when the burner assembly is intact

• Turn off gas supply and power to the appliance before servicing
• Handle with care to avoid bending or damaging the burner ports and mounting tabs
• Inspect gaskets/seals and replace if damaged to prevent leaks

The Igniter is an OEM part for GE dryers. This part is responsible for generating a spark or glow that ignites the gas, producing the necessary heat to dry your clothes effectively. It ensures that the dryer reaches and maintains the desired temperature throughout the drying cycle.

A bad igniter can occur due to wear and tear, electrical malfunctions, or damage from excessive heat. If you notice symptoms such as the dryer not heating up, a lack of heat during the drying cycle, or the burner not igniting, it may be time to replace this part.

Symptoms of a bad igniter include:

• Dryer not heating up
• Lack of heat during the drying cycle
• Burner not igniting

Restore your GE dryer by replacing the faulty igniter with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This manufacturer conversion kit lets a compatible gas range or oven be converted from natural gas to liquid propane (LP) so burners and oven work safely with the correct orifices and regulator settings. Ideal when changing fuel types or installing in an LP-supplied home. What it does:

• Replaces factory orifices and settings so burners and oven operate correctly on LP fuel
• Helps restore proper burner flame size and heat when fuel type has changed
• Used when appliance will not light reliably or produces improper flame shape after fuel conversion
• Required safety step before operating a natural-gas-configured appliance on propane

• Must be installed following the manufacturer's instructions and labeling included with the kit
• Turn off gas supply and electrical power before beginning work
• After installation, check for gas leaks and verify proper burner flames and regulator operation before use