Need Help?
Call
Secondary relay board that switches power to cooktop burners and heating elements. Replace if cracked, damaged, or causing intermittent control issues.
I repaired the problem by replacing the Power Board assembly and the daughter relay board. Not sure which one was the problem. Since I had it apart I replaced both. So far the unit is working like new. Everything was plug in, so I didn't have to worry about complex wiring. I took pictures prior to disassembly to make sure I got the reassembly right. Worth the effort to fix it- very satisfying. Read more
Oven won't heat or ignitor doesn't glow? A failed control board prevents baking and broiling. This replacement restores temperature control and operation.
Ordered a new panel and replaced the old one Read more
Fix a non-responsive display, blinking lights, or cooling failure. This power supply board restores proper voltage to electronic controls and displays.
It needed a new control board . I replaced the same board 6 years ago Read more
Fix random beeping, locked controls, or self-cleaning errors. This control board governs display, timers, and temperature relays. Moderate difficulty.
I looked up the part numbers, ordered them from Appliance Parts Pro and they arrived the next day. Followed the video to replace the parts - it was super easy and now everything works great again! Saved lots of time and money. Read more
Fix oven that won't heat to correct temperature or won't turn on. This control board regulates heating cycles. Moderate DIY install, 1-2 hours.
I put in a new oven control board. So instead of putting the temp knob 80 degrees higher than it should, I dont have to do that anymore. The best part is I get to make our gingerbread houses as gifts! Because of a great support staff that worked on sunday the two gals there know their stuff. Its nice to work with a nice and efficient co. Will be back when other stuff breaks down because when you fix one thing the other appliances get upset when they dont get any attention. Trust me this... Read more
This genuine replacement part is a user interface board for dryers. The user interface board is the circuit board that responds to the buttons located on the control panel allowing the user to adjust the dryer settings. If the dryer is no longer responding when buttons are being pressed then it might be time to replace the user interface board. Luckily this is a relatively easy repair.To replace the interface board begin by turning off the power to the dryer. Once the power has been shut off move the dryer away from the wall to gain access to the upper back panel. Remove the panel and locate the interface board. Snap it out of its brackets and remove the wire harness attached to the board. Reinsert the wire connector to the new interface and snap the new board assembly back to its original place.This OEM replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand Dryers.
Replacing the board took about two minutes from start to finish after removing the select knob. Extremely easy but costly. Read more
If your oven won't heat or displays error codes, the relay board may have failed. This assembly routes power to burners and heating elements.
Fix a dishwasher that won't cycle properly, hangs mid-wash, or resets to default settings. This electronic control board restores normal operation. DIY-friendly.
I noticed something was wrong when the dishwasher no longer remembered the last cycle performed. After it finished, it would go to a default cycle. A couple of weeks ago, my husband said it wouldn't start. Then I noticed on subsequent washes, there was a high probability that it would hang at a random part of the wash cycle. I was able to reset it though. The last time it stuck was during the pre cycle, where it drains any water and runs the disposer. It hung there all night! I tried cycling... Read more
Fix a dishwasher that won't advance cycles or gets stuck in wash mode. This control timer restores proper cycle progression and timing functions.
Control board that mounts to the main control assembly. Replace when board is burned, damaged, or relays have failed to restore proper operation.
Replaced daughter board but problem persisted. Rather then buying a $260.00 control. I bought a new cooktop. I was afraid that also might not fix my problem. I was very much impressed with your tech. She done a good job trying to help me. Read more
Fix unresponsive buttons or blank display on your dishwasher. This control board and keypad kit restores electronic controls. Moderate DIY, 30-45 minutes.
I replaced the circuit board behind the pushbuttons. At first there was no change in the controls, then i remembered that the door needed to be closed for it to work. Yah! It works now. $119 parts and installed it myself vs. $450 for a new machine. Read more
If your dispenser light stays off or won't turn on, this control board restores proper illumination. Moderate DIY, requires clip release and wiring.
Chatted online with a an individual from Appliance Parts Pros regarding replacement bulbs and instructions for our GE Profile PSHW6YGXCDSS Side-By-Side Refrigerator and our GE Advantium SCA2001 Cooking Tool. He gave me the part numbers for the bulbs and they were ordered and delivered very quickly. The bulbs for the the Advantium (WB36X10328 ) were easy to replace using just a screwdriver to remove and replace the protective covers under the appliance. However, the bulbs for the ... Read more
Dishwasher won't advance through cycles or stops mid-wash? The control timer regulates washing, rinsing, and drying phases. Moderate DIY repair.
Refrigerator not cooling properly or freezing everything? A failing main control board disrupts compressor and fan cycles. Moderate DIY repair restores temps.
Dryer won't advance through cycles or stops mid-cycle? This timer and wiring harness kit restores accurate cycle control. Moderate DIY repair.
This is an electromechanical timer that controls the duration and sequence of the dryer's operating cycles. It advances through each stage of the drying cycle and signals the motor, heater, and other components when to turn on and off. Replace this timer if your dryer won't start, won't advance through cycles, runs continuously without shutting off, or if the timer knob turns but nothing happens.
Bought a new timer switch, 2 minute install, waalaa....fixed....easy as pie! Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.