Need Help?
Call
The Return Switch is an OEM part for GE trash compactors. This part ensures that the compacting ram returns to its starting position after each compaction cycle.
Causes of a malfunctioning return switch can vary from electrical issues, such as short circuits or worn-out connections, to mechanical problems, including physical damage from wear and tear or blockages preventing the switch's activation.
Symptoms of a faulty Return Switch include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
TALKED TO YOUR REPRESENTATIVE AND WE WENT THROUGH ALL THE ON/OFF AND LIMIT SWITCHS. NARROWED IT DOWN TO TWO SWITCHS. THE ON/OFF SWITCH AND THE LIMIT SWITCH ON THE DOWN CYCLE SIDE. REPLACED ON/OFF AND DETERMINED THAT THAT WAS NOT THE ISSUE. THEN UNCOVERED LIMIT SWITCHS AND REPLACE DOWN SWITCH, FIXING THE PROBLEM Read more
Burner stays on high or won't turn off completely? This infinite control switch regulates surface burner heat. Simple 10-minute DIY fix with video guide.
I first checked a repair video and found the procedure was a 10 minute job. I then went to the website, put in my stove model number and searched for the switch. While I was looking I was offered a chat session with one of their experts. I am glad that I accepted. The switch I was looking at was not the right switch for the job. My expert verified my model number and the switch that need to be replaced. After a couple of minutes, she came back with the right part and placed the order for... Read more
Fix a dryer that won't start or has a broken start knob. This rotary start switch is located in the control panel. Easy 5-10 minute DIY repair.
Ordered parts arrived in two days. Ten minute fix with one wrench. Should have done it years ago. Read more
Microwave tripping breaker when door opens or at startup? A failed monitor switch with welded contacts is the likely cause. 30-minute DIY repair.
By replacing the switches. Read more
Burner won't stay at set temperature or jumps to high? The infinite switch controls power to heating elements. Easy DIY repair, takes under 30 minutes.
Very easy replaced switch. Read more
Fix washer overfilling or not filling properly. This pressure switch controls water level for proper washing. DIY-friendly, takes about 5-10 minutes.
I thought initially it was a hose because it was leaking water from the bottom. On the small and medium load it didn't leak. I watched it on the large setting and noticed the water didn't shut off initially so therefore it was over filling. I ordered a switch pressure switch from Appliance Parts Pros and received it in two days. I replaced the switch, put the washer together and now it works like new. The wife is very happy to have her washer back working better than ever! Thanks! Jerry Read more
Fix a washer that won't fill properly or overfills with this water level pressure switch. Common when load size selector fails. 20-minute repair.
Removed fill level pressure switch knob. Removed three screws from the back of the control panel.Opened the control panel and removed electrical connector and plastic tube from the pressure switch. Removed and replaced pressure switch. Placed control panel to correct position and replaced the three screws. Read more
Burner stuck on high or can't regulate heat? This infinite switch controls cooktop element temperature. DIY-friendly repair in under an hour.
Ordered the element control for my dual front right burner and a infinite heat switch for my left front large single burner. Removed cooktop and followed the instructions video given with the parts online. Process was simple and everything on my cooktop is working like it is brand new. The only problem I have is with the online chat, save time by calling in and talking to someone as the people I talked to online (4 of them) are in such a hurry to get to the next call they gave conflicting part... Read more
Burner stuck on high or won't adjust temperature? This range infinite switch controls surface element heat levels. Common DIY fix for uneven heating.
Replace the switch (part # WB24T10012). Read more
The Switch Gas Valve is an OEM part for GE ranges. It is responsible for controlling the flow of gas to the burners, allowing them to ignite and maintain a steady flame for cooking.
Causes of a bad switch gas valve can include wear and tear over time, buildup of debris or grease, or damage from repeated use or accidental impact. These issues can hinder the valve's ability to regulate gas flow effectively.
Symptoms of a bad switch gas valve include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Bought this switch gas valve for the non-functional burner, and it cleared right up. Read more
If your cooktop burner is stuck on high or won't adjust temperature, the infinite control switch likely failed. This part controls heat levels.
The parts are under the stovetop and the knobs are attached to them. We bought the correct ones from AppliancePartsPros, these were the correct ones. Seems we have an oddball stovetop. It's a GE drop in stove. The parts were easy to change. It was a simple matter of putting the wires on the new switch in the same place there were on the switch. I took phone pics of the wire locations before I took them off and only did one switch at a time. Turn the power off at the breaker panel first of... Read more
The Rocker Switch is an OEM part for GE ranges. This switch is used to control the surface heating elements, allowing users to turn them on or off and adjust the heat levels. It is designed to fit securely into the range's control panel, providing reliable operation and ease of use.
Causes of a bad switch rocker element can include regular wear and tear, electrical issues, or damage from spills or high temperatures. Over time, the internal contacts of the switch can degrade, leading to malfunction.
Symptoms of a bad switch rocker element include:
Replaced the switch took a total of about five minutes. I pulled the stove out and turned the breaker off so I only had to pull it out enough to get a 1/4 " nut driver in behind it. Removed three screws and the back cover came off. I pushed the switch threw from the back and switched over the two wires then reversed the process. Completely easy if you can use a screw driver your crazy not to replace it yourself Read more
Fixes burner stuck on high or no heat issues. This infinite switch regulates cooktop element temperature by cycling power on and off. Simple replacement.
Just a simple install my maintenance man just put it in with no problems. Read more
If your gas burner won't light or keeps clicking after ignition, the igniter switch may be faulty. This switch closes when you turn the knob to spark.
Ordered an igniter switch for $21.95. (the left front handle was turned the wrong although clearly marked: Off, Lite, X-high, high, med, low, simmer. Guess some folks cannot read and deduce.) When we returned from out of town to relieve the sitting family members I noticed the left front burner handle was sitting at 11 o'clock instead of true OFF at 12, straight up and down. When I would correct the position the ignitor would begin until I once again would back it up until the light would go... Read more
Burner stuck on high or not heating? This infinite switch regulates cooktop burner power. Typical DIY repair takes about 30 minutes with basic tools.
We replaced the Control Switch, Read more
Fix a washer that won't agitate or spin with this lid switch. This safety part detects if the lid is closed. Easy DIY repair with basic tools.
Replaced lid switch and capacitor Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.