General Electric Valve

Note: This is the complete solenoid assembly kit. For armature & linkage assembly only, use WD1X1316.

The Solenoid Assembly is an OEM part for GE dishwashers. It plays a crucial role in controlling the flow of water into the dishwasher by activating or deactivating the drain valve. This assembly is essential for ensuring that the dishwasher fills and drains at the correct times during the wash cycle, which is pivotal for the overall efficiency and effectiveness of the appliance.

Common causes for a Solenoid Assembly to fail include wear and tear over time, mineral buildup from hard water, or electrical failures that prevent the solenoid from operating as intended. 

Symptoms of a bad Solenoid Assembly include:

• Failure of the dishwasher to drain properly, leading to water accumulation at the bottom.
• The dishwasher not filling with water as it should, affecting the cleaning process.
• Unusual noises coming from the dishwasher, which may indicate the solenoid is failing to engage or disengage correctly.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This GE Oven Safety Valve is an OEM replacement part for GE ranges. The part's primary function is to prevent gas from releasing until the igniter has received enough voltage to ignite it safely. Not allowing any gas to exit before ignition helps avoid potential safety hazards from uncombusted gas.

Causes for failure could include wear and corrosion over many years of use. Repeated heating and cooling stresses may cause cracking or breaking in the valve's delicate regulating components. Mineral deposits or dirt buildup may also obstruct proper opening and closing.

Symptoms of a faulty safety valve would include:

• gas releasing or leaking even when the igniter is not lit
• the oven or burners not lighting at all when the valve is engaged

This GE OEM part is also compatible with Hotpoint, RCA and select Kenmore models.
 

The 2 In 3 Out Water Valve is an OEM replacement part for GE washing machines. It is located within the water supply system to help regulate water flow into the washer tub. 

Causes of failure can include obstruction or clogging from mineral deposits over time. Valve components may also wear out with extended usage.

Symptoms of a faulty water valve include:

• Extended or interrupted cycle times 
• Fluctuations in water levels inside the tub
• Weak water pressure levels for filling and rinsing  
• Leaks from the water inlet area of the washer

Compatible models include GE, Hotpoint, RCA, and select Kenmore models.

The Water Inlet Valve is an OEM replacement part for GE refrigerators. As a key component in the refrigerator's water delivery system, the inlet valve is responsible for controlling the flow of water from the main water line into the refrigerator. It precisely regulates water pressure and quantity to ensure optimal performance of the ice maker and water dispenser. 

Causes of a bad water inlet valve can include mineral or sediment buildup interfering with water flow, wear and tears to seals or internal components, or damage from freezing. 

Symptoms of a bad valve include:

• Slow or inconsistent fill times for the ice maker or water dispenser  
• Odd sounds or grinding noises coming from the valve area
• Water leaks in or around the valve
• The ice maker or water dispenser failing to operate properly or at all

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore refrigerators.

The Water Valve is an OEM replacement part for GE side-by-side refrigerators. As part of the internal plumbing system, the valve controls the supply of water into the refrigerator for ice and water dispensing functions. It opens and closes precisely based on electronic signals from the control board.

Causes of a bad water valve can include mineral buildup disrupting water flow, seal deterioration from repeated use, or damage due to freezing temperatures. 

Symptoms of a bad water valve include:

• Slow fill times for the ice maker or water dispenser  
• Odd sounds coming from the valve area 
• Water leaks at the valve inlet/outlet ports
• Failures of the ice/water dispenser to function normally

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

The Filter Ball is an OEM replacement part for GE dishwashers. As a key internal filtration component, it helps trap and remove food soils and other residue from washing water to maintain hygienic cleanliness standards. 

Causes of a bad filter ball can include worn filter mesh that no longer adequately strains soils or substances that pass through more readily over time. 

Symptoms of a bad filter ball include:

• Dirty wash water that fails to fully sanitize dishes
• Cloudy rinse water that leaves behind streaks and residue 
• Excess food debris collecting in drainage areas 

This GE replacement filter ball is also compatible with some Hotpoint, RCA, and Kenmore dishwashers.

The Check Valve Flapper is an OEM replacement part for GE dishwashers. It is a small but crucial component located within the water inlet valve assembly. The check valve flapper regulates water flow into the dishwasher, allowing water to enter during the fill cycles but preventing backflow when the water is drained. 

Causes of a bad check valve flapper can include wear and tear over time, mineral buildup that causes sticking, or damage to the flapper itself. This prevents the flapper from opening and closing as intended.

Symptoms of a bad check valve flapper include:

• Slow or incomplete filling of water 
• Dripping or leaking water from the inlet area
• Error codes related to water issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dishwasher models. 

The Water Inlet Valve is an OEM replacement part for GE washing machines. As the valve responsible for regulating water flow into the washer, it plays an important role in allowing cycles to run properly.

Causes may involve mineral buildup clogging the valve over time, damage to internal components, or deterioration of valve seals. Replacing with this genuine GE part ensures optimal water input for thorough, effective cleaning cycles.

Symptoms of a bad water inlet valve include:

• Inconsistent or interrupted water fill during cycles
• Prolonged fill times or inability to reach proper water levels
• Dripping or leaking from the inlet area of the washer
• Cycles failing to start or complete normally due to water issues

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Water Valve and Bracket Kit is an OEM part for GE refrigerators. It includes a water valve and a mounting bracket designed to facilitate the connection and operation of your refrigerator's ice maker and water dispenser system. This part controls the flow of water into the refrigerator, ensuring that both the ice maker and water dispenser receive the proper amount of water at the correct pressure.

Causes of a bad Water Valve and Bracket Kit can include mineral deposits from hard water, which can clog or damage the valve, and normal wear that might cause the valve to leak or fail to open or close properly.

Symptoms of a bad Water Valve and Bracket Kit include:

• No water output from the dispenser
• Slow or no ice production
• Water leakage around the refrigerator

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Triple Water Valve is an OEM part for GE washing machines. This valve controls the flow of hot, cold, and warm water into the washing machine, ensuring the proper temperature and water level for each wash cycle. It is a critical component for the accurate filling and rinsing functions of the washer.

Replace the triple water valve if it becomes faulty due to mineral buildup, wear and tear, or electrical issues. 

Symptoms of a bad triple water valve include:

• The washer not filling with water
• Incorrect water temperatures during cycles
• Water leaking from the valve
• Slow or uneven water flow into the machine

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Drain Solenoid is an OEM part for GE dishwashers. This component controls the draining function by opening and closing the drain valve, ensuring that water is properly expelled from the dishwasher at the appropriate times during the wash cycle.

Common causes of a bad drain solenoid include electrical malfunctions, buildup of debris or mineral deposits, and general wear over time. These issues can prevent the solenoid from operating correctly, leading to improper draining.

Symptoms of a bad drain solenoid include:

• Standing water at the bottom of the dishwasher after the cycle
• Unusual noises during the draining process
• Error codes related to draining
• Water leakage from the dishwasher

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Inlet Valve Assembly is an OEM part for GE washing machines. This part controls the flow of water into the washer during the fill and rinse cycles.  

Causes of a bad inlet valve can include regular wear and tear, mineral deposits from hard water, or electrical issues.  

Symptoms of a bad inlet valve assembly include:

• The washer not filling with water or filling too slowly
• Water leaking from the valve area
• The washer filling with water when it is not supposed to
• Inconsistent water levels during cycles

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This surface burner control valve regulates gas flow to a single cooktop or range burner, allowing smooth ignition and precise flame adjustment. Replace a worn or stiff valve to restore consistent, reliable burner control.

• Regulates gas from the manifold to an individual surface burner as the knob is turned
• Opens/closes the gas path to ignite and adjust flame height
• Helps maintain a steady flame at low and high settings
• Common symptoms: burner won't light or only lights with a match, flame won't adjust or is uneven, control knob hard to turn or seized, gas odor near the control area

• Disconnect power and shut off the gas supply before servicing
• Remove the knob and access panel to reach the valve; label and disconnect gas tube fittings
• Support the manifold with a second wrench when loosening/tightening fittings; do not overtighten
• After installation, restore gas and check all connections for leaks using a non-flammable leak-detection solution; verify proper ignition and flame adjustment

This refrigerator water inlet valve controls the incoming household water supply to the dispenser and icemaker. When energized, it opens to allow water flow, helping restore reliable dispensing and proper ice production.

• Regulates water flow to both the dispenser and the icemaker
• Common failure signs: no or slow water dispensing, no ice production, small/hollow ice cubes, valve humming but no water, or water leaking from the valve body
• Electrical solenoid-operated design opens only when signaled by the control system
• Helps maintain consistent water delivery and ice fill levels

• Disconnect power and turn off the household water supply before servicing
• Place a towel or pan to catch residual water; relieve line pressure carefully
• Transfer tubing and wire connectors one at a time to the new valve to avoid mix-ups
• Check for leaks after installation; do not overtighten compression fittings

This triple water inlet valve regulates the hot/cold water supply and dispenser fills in your washing machine. Replacing a failing valve restores proper fill control and temperature selection, helping address slow fills, no fill, or water seepage into the tub.

• Regulates incoming water flow as directed by the washer's control system
• Mixes hot and cold supply to achieve the selected temperature
• Routes water to the tub and dispenser during appropriate cycles
• Common symptoms include no/slow filling, only hot or only cold working, or water dripping into the tub when the washer is off

• Disconnect power and turn off both water supplies before servicing
• Place towels to catch residual water; label and disconnect hoses and wire connectors
• Inspect inlet screens and flush supply lines before reconnecting
• Restore water and power, then run a fill test and check all connections for leaks

Refrigerator primary ice and water dual coil water inlet valve. For the filter valve order WR57X10024. For the assembly including both the primary and filter valve having the short bracket order WR57X10026. For the assembly including both the primary and filter valve having the long bracket order WR57X10022.