Parts for Remington 41AZ56WG983: General Assembly Parts

This part is a drive gear that is used on chainsaws. A drive gear is what carries the power from the clutch to the sprocket that holds the chain. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.A new drive gear may be needed if the chain is no longer moving. If any of the spokes on the gear are damaged, the chain will not move properly. The drive gear will need to be replaced if it is cracked, broken, or damaged in any way. Use extreme caution when making any repairs on a chainsaw. Never perform care and maintenance on a machine that is powered on.This drive gear is a genuine MTD part. It is sold individually. This particular drive gear is compatible with chainsaws that are manufactured by MTD, Craftsman, and Remington.

This is an authentic roller bearing replacement specifically for use with chainsaws. The roller bearing uses a cylinder, which is the roller, rather than a ball. These types of bearings help to allow for greater radial loads than ball bearings. In the chainsaw, they can help to reduce friction and provide smoother motion between the parts. The chainsaw roller bearings tend to have a lot of wear and tear from repeated use. This means that over time, they can start to wear out. Owners who find that the chainsaw is not functioning smoothly as it did before might want to check on and replace their roller bearings. If there is low oil pressure or if there are knocking noises in the engine, it could be due to bad bearings. These are genuine OEM roller bearings for use with chainsaws. This set comes with two roller bearings. Buyers might want to have some extra on hand for the next time they need to change out the bearings. Compatible brands for this product include electric chainsaws from Craftsman and MTD.

This Craftsman sprocket gear assembly fits Remington chainsaws. The sprocket is designed to drive the proper-pitched chain around the guide bar. One of the most important components of the chainsaw is the sprocket. A skipping, jerking, or a dragging/stretching action are signs that the sprocket needs to be changed. Worn out sprockets affect the efficiency and working of the chainsaw, and can result in wear on all the other components connected to it. It is recommended to be changed every two or three years. Replacing the sprocket can be done in only a few steps. First, take off the top cover. Next, take off the spark plug wire and battery cables. Users will also need a piston tool to lock the piston in place. Remove the clutch and then remove the old sprocket. If needed, lubricate it. Reassemble everything in the reverse order. A good working sprocket will keep the chainsaw and its components lasting longer and working better. This is a genuine OEM part sourced directly from the manufacturer and sold individually.

The sprocket/gear assembly is a genuine replacement part that helps drive the chain in select MTD chainsaws. It is located under the engine cover housing and connects to the chain drive to create the motion that rotates the blade. Over time and with constant use, the gear and sprocket can both become worn down or develop issues that cause them to affect the operation of the saw. In this case, the best option is to replace the defective or damaged parts. This sprocket and gear assembly provides an exact fit for compatible equipment since it is an identical part. This genuine OEM replacement part is compatible with dozens of chainsaws and pole saws and is manufactured to exact standards. This durable sprocket and gear are made of premium composite and metal materials and the assembly is sold as a single unit. Allow the engine to cool completely and wear gloves for safety whenever performing any type of engine repairs. The spark plug should also be disconnected before working on the engine for the safe repair of all parts.

This replacement part is a nut. This is a genuine replacement part made by MTD. Nuts are small but important to the overall workings of many appliances. These parts work with other small pieces such as screws and washers to keep parts safe and secure during use.A new nut might be needed if the current one is missing or damaged. This can be caused by normal wear and tear with years of extended use. Nuts can experience large amounts of friction over time and may become worn down after a while. Refer to the user manual for specific directions on the replacement of this part. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This replacement part is an adjustment block. It is a genuine replacement part made by MTD. This part is usually found in chainsaws and allows the user to adjust the tightness and position of the chain that is being used. A new adjustment block might be needed if the user notices that the current chain is becoming lose or being moved from its original position and the user cannot adjust it. The adjuster block can become damaged over time due to normal wear and tear and it is recommended that it be replaced if this is the case. Be sure to refer to the specific user manual for more information on replacing this part. This adjustment block is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer to ensure long-lasting use.

This e-ring clip is a fastener made of semi-flexible metal in a ring shape with open ends so it can easily be snapped into place. These items are sized in a way to offer an interference fit into or onto a land or groove when in use. Installing or removing an e-ring clip requires them to be elastically deformed. These clips can become worn from use or damaged due to heavy loads or the presence of corrosive substances.If an e-ring clip is malfunctioning, it should be replaced. This can be done with an e-clip remover, a pair of pliers, or a flathead screwdriver. E-rings are designed to snap into a groove cut into a round shaft. To install a new clip, place the open ends against the shaft and apply pressure. This is best done using needle nose pliers rather than fingers. Once the new e-ring clip is installed, the chainsaw can be used as normal.This e-ring clip is designed for use on chainsaws manufactured by MTD and Craftsman. It comes as an individual OEM part that is sourced directly from the manufacturer. A pair of pliers, a screwdriver, or an e-clip remover may be needed to replace the e-ring clip.

This chain tensioning screw is a genuine MTD part, sold individually. This chain tensioning screw can be used as a replacement part in a chainsaw. The purpose of the chain tensioning screw in a chainsaw is to provide a secure source of stability for the chain while it is in use.The chain tensioning screw might have to be replaced at some point within the typical lifespan of the chainsaw if the chain tensioning screw can no longer ensure that the chain stays firmly in place while rotating. If the chain is frequently slipping due to a chain tensioning screw that has been worn out over general use or that has suffered from some other form of damage, the chain tensioning screw should be removed and replaced by this genuine OEM replacement part.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This chain tensioning screw is compatible with the following outdoor appliance brands: MTD and Craftsman.

This replacement part is a nut. This is a genuine replacement part made by MTD. Nuts are small but important to the overall workings of many appliances. These parts work with other small pieces such as screws and washers to keep parts safe and secure during use.A new nut might be needed if the current one is missing or damaged. This can be caused by normal wear and tear with years of extended use. Nuts can experience large amounts of friction over time and may become worn down after a while. Refer to the user manual for specific directions on the replacement of this part. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This part is a replacement adjustment block. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a broken or defective adjustment block in outdoor power equipment.This adjustment block is essential to proper equipment functionality and will need to be replaced if broken, faulty, detached, or ineffective in any way. When working on or near an engine, it's important to make sure the equipment is powered off and completely cool before starting any repairs. For more accurate information on how and where to install this adjustment block, the appropriate owner's manual and equipment diagrams should be utilized.As an authentic replacement part, this adjustment block is suitable for use on outdoor power equipment manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Please note that this is a genuine part made of high-quality, durable materials and is sold individually.

This adjustment screw is a genuine MTD part. An adjustment screw can be used as a replacement part in a chainsaw. The purpose of this genuine OEM part is to facilitate the stable placement of one or more components within the chainsaw through its fastening mechanism.The adjustment screw can be easily lost or misplaced, as it is a small fastening component, the absence of which might not be immediately noticed by the operator. If this occurs, or if the screw is damaged, the adjustment screw might need to be removed and replaced by this genuine OEM replacement part.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This adjustment screw is compatible with equipment manufactured by MTD.

This part is a replacement bar adjuster screw. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part's intended use is to replace a broken, stripped, or defective bar adjuster screw in chainsaws.The bar adjuster screw enables the user to easily adjust the tension of the bar. This ensures that the chain is held tightly and securely in place. If this part is broken, lost, or faulty, the chainsaw may not work to the best of its ability. When working on or near an engine, it's important to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this bar adjuster screw, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality metal. This bar adjuster screw can be used with different models of chainsaws that have been manufactured by MTD, Craftsman, and other brands. Part sold individually.