Parts for Ge AEM05LVL1: Grille & Chassis Parts

This connection bar is a cabinet-mounting support piece that secures panels or components to the appliance cabinet for stable alignment and reduced vibration. It restores proper fit and helps maintain door/panel positioning. What it does:

• Provides a secure attachment point between an internal component or panel and the appliance cabinet
• Helps eliminate panel rattling, vibration, or minor misalignment
• Maintains correct spacing and support for fitted panels or assemblies
• Supports long-term stability of the mounted component

• One connection bar to cabinet

• Disconnect power to the appliance before beginning any repair
• Remove any panels or trim that block access to the mounting location; keep fasteners organized
• Use appropriate hand tools and avoid over-tightening fasteners to prevent damage

This door gasket seal replaces a worn or damaged refrigerator or freezer door seal to restore a tight closure and help maintain proper temperature. It helps stop air leaks that can cause frost build-up and higher energy use. What it does:

• Forms a replacement seal around the appliance door to maintain an airtight closure
• Helps reduce interior temperature fluctuations that can lead to frost or spoiled food
• Restores proper door alignment and sealing where old gasket is cracked, torn, or compressed
• Commonly used when you see visible gaps, drafts, or persistent moisture at the door edge

• Designed for a direct OEM-fit; inspect the door channel and mounting surface before installing
• Clean the gasket channel and door edge to remove debris for best sealing contact
• Warm the gasket slightly (per OEM guidance) if needed for easier fitting; avoid open flames

This accordion panel seal replaces the flexible gasket that seals the appliance cabinet panel, helping keep the cabinet closed and reducing drafts, dust, and vibration noise around the panel area. What it does

• Replaces worn or torn accordion-style gasket on the cabinet/panel edge
• Restores a snug seal to reduce drafts and prevent dust or lint from escaping
• Reduces panel vibration and rattling caused by loose or damaged seals
• Helps maintain proper airflow routing by sealing the cabinet opening

• Disconnect power to the appliance before beginning any repair
• Removal of the front or cabinet panel is typically required; keep fasteners organized
• Handle edges and clips carefully—use proper tools to avoid damaging the seal or cabinet
• Follow OEM disassembly/reassembly instructions

This air filter assembly traps dust and lint before they reach the evaporator coil, helping your room air conditioner maintain airflow and cooling performance. Replace clogged or damaged filters to protect components and keep cooling consistent. What it does:

• Screens intake air to help prevent debris from coating the evaporator coil and blower
• Helps sustain proper airflow and cooling performance
• A torn, missing, or heavily clogged filter can cause reduced air volume, longer run times, or uneven cooling
• Captures dust and lint that would otherwise accumulate inside the unit

• Includes: 1 air filter assembly

• Unplug the unit before servicing
• Open the front grille to access the filter; note the orientation of the old assembly
• Slide out the old filter and fully seat the new assembly in the same position
• Do not operate the unit without a filter installed

This curtain assembly is the extendable side panel for a window air conditioner. It fills the gap between the A/C cabinet and window frame to restore a secure fit and help block drafts, moisture, and debris.

• Extends to close the side opening between the unit and the window jamb
• Helps reduce unwanted airflow, dust, moisture, and insects around the A/C
• Aids in maintaining a stable, properly aligned window installation
• Common symptoms: cracked or torn panel, brittleness, missing panel, visible light or air leaks at the sides

• Disconnect power and support the A/C so it cannot shift or fall while servicing
• Remove the damaged panel and retain any screws or mounting clips for reuse
• Slide the new curtain into the cabinet tracks and secure it to the window frame per your model's instructions
• Match orientation to the original panel and ensure smooth extension and an even seal before use

The Top Rail is an OEM part for GE air conditioners. This rail is responsible for for securely mounting and supporting the air conditioner unit in the installation location.

A bad top rail can be caused by damage, rust, or improper installation. If you notice instability, sagging, or misalignment of your air conditioner unit, it may indicate a problem with the top rail.

Symptoms of a bad top rail include:

• Unstable or wobbly air conditioner unit
• Difficulty in securely mounting the unit
• Visible damage or signs of wear on the rail
• Uneven weight distribution or tilting of the unit

Replace your faulty top rail with this genuine OEM part to restore your air conditioner unit. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.